Identify the system for a house The following figure illustrates a simplified schematic of a house with the flow of water and electricity. Considering the entire house as the system, identify the boundary of the system, its interaction with its surrounding, and its internal events for each case. Repeat the question for the water heater and then dishwasher as the system. Shower L Water meter Cold Hot -Drain lines -Dishwasher Hot water -heater Electric meter

Identify the system for a house The following figure illustrates a simplified schematic of a house with the flow of water and electricity. Considering the entire house as the system, identify the boundary of the system, its interaction with its surrounding, and its internal events for each case. Repeat the question for the water heater and then dishwasher as the system. Shower L Water meter Cold Hot -Drain lines -Dishwasher Hot water -heater Electric meter

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Please show the complete solution. (Example: Conversion of Units) If the energy efficiency ratio of the refrigeration system is 12.6, what is the COP of the system?
11. Athermally insulated battery is being discharged at atmospheric pressure and constant volume. During a 1 hour test it is found that a current of 50 A and 2 V flows while the temperature increases from 20°C to 32.5°C. Find the change in internal energy of the cell during the period of operation. [Ans.-36 x 104 J]
The left side of this equation tells how much energy Q the cylinder gives to the water while it cools. The right side of this equation tells how much energy Q the water and aluminum cup absorb from the cylinder to warm up. Because it is the same energy, they are equal. What is known in this equation? Mcyl 411.7 g, malum 46.5 g, malum+water = 175 g Can you find: mwater =? g Twater = Talum = 20°C (water and cup of room temperature) 90°C, T; = 35°C (hot cylinder and cool "cylinder+cup+water" temperatures) Tcyl kCal Calum = 0.22, Cwater 1 (specific heat of water and aluminum, measured in units kg-°C What are we looking for is Ccul - How we find it? Plug all the numbers into the equation (1), Ccul will be one unknown which you can calculate from the equation. Important, convert all the masses from grams to kilograms! After you find Ccyl, compare it to known value for the copper 0.093(our cylinder is made out of copper). |Ceyl -0.093| % : · 100% 0.093
The figure below shows a schematic of a dual-duct system For design purposes, suppose the zones shown are two of five zones, each having identical operating design conditions. The only exhaust is the main system exhaust. The zones are to held at 75 °F db / 50% RH when the total heat gain of each one is 200,000 BTUH and the sensible heat ratio is 0.6. Outside air (OA) is 95 °F db / 40% RH and the system is designed to operate with a mass flow rate of dry air that contains 25% OA & 75% RA (return air). The hot deck provides sensible heating only, and the air exits the heating coil at 105 °F db. The cold deck is designed such that air exits the cooling coil at 50 °F db / 90 % RH. Take the pressure to be one standard atmosphere. a. Accurately sketch and label the state points on an electronic psych chart (in particular make sure that the coil is represented as a collie on the TRANE pscyh chart software you can input a coil process) b. Compute the mass flow rate (lbma/hr) through…
A resistance heater is placed inside a rigid insulated tank containing 0.25 kg of nitrogen for the purpose of heating the nitrogen. A current of 0.3 Amps is supplied to the heating element that has a resistance of 60 Ohms. a. Find the time required for the heater to provide 1500 Joules. b. Find the temperature rise in the nitrogen. (Use appropriate specific heat corresponding to a temperature of 300 K).
The specific internal energy of water at 10 psia and 220 °F is Btu/lbm. Numeric Response
What are the types of temperature sensors / devices used in industrial applications? (Give atleast 5 thermocouple sensors).
SHOW SOLUTION STEP BY STEP WITH UNITS. SUBJECT: THERMODYNAMICS TOPIC: PROCESSES OF GASES
Q2 Figure Q2 shows the schematic diagram of wind turbine which used in power plant. By using the exact solution method, it is found that the fundamental natural frequency for the system is wn = 0.6/kt/J rad/s. Assume that J, =J2 = J, and k; = k;2 = kị. By using Rayleigh's method, predict the fundamental natural frequency in Hertz natural frequency in Hertz unit and its corresponding mode shape for Q2(a) answer if the initial trial vector is (). Use J= 2, and k, = X, and show up 2.9 %3D X=6 Rotor Hub - Low-speed shaft - Gearbox J, - High-speed shaft Nacelle- |02 Tower LGenerator J: Figure Q2 Blade Blade
which equation is used if the system underdamped. can you pls share the whole eqn
Model the problem in terms of a differential equation
Your first customer asked for an air piston-cylinder to use it in air compressors for generating high pressure. Your role in your company is to analyze, describe the operation of the system and their properties, explain and demonstrate the application of the first law of thermodynamics to this system, as well as, illustrate the importance of expressions for work done in the system through the application of the first law. Air Figure 1:Schematic for the air piston-gylinder. The required piston-cylinder device is frictionless and initially contains 3 kg of air at 150 kPa in 0.2 m?. The air is now heated by using a fire. Also, a mechanical shaft is rotating. Then the piston starts