If a J-type thermocouple is used in a standard two-junction thermocouple configurationwith a 100°C reference temperature, what measurement temperaturewould correspond to a measured voltage of 30 mV? Given Vr/100 = 30mVHint:Solve the above polynomial eq. for V100/0 using MATLAB, Mathematics, Maple, or othermathematic software. After you get 100/0, use Law of Intermediate MetalsEq VT/0-VI/100+V100/0 and eq.:I=c++++++7/07/0

Calculate V_(100/0): We have the equation: VT/100=30,mV. To find V100/0, we can use the Law of…

Answered: If a J-type thermocouple is used in a…

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter19: Special-purpose Outlets-water Pump, Water Heater

Section19.2: Water Heater Branch Circuit

Problem 8R: For residential water heaters, the Consumer Product Safety Commission suggests a maximum temperature...

See similar textbooks

Similar questions

Number 9 Please show your detailed solution. Number 9 Please show you detailed solution. A 50-ohm resistor is in series with a 40-?F capacitor across a constant potential source of 180 volts. Determine frequency that will give current of 3.13 amp. A. 250 Hz C. 160 Hz B. 200 Hz D. 140 Hz
2. Sketch vi , vd , and Id for the half-wave rectifier of figure below. The input is a sinusoidal waveform with a frequency of 60 Hz. Sketch v L and i L. Compute for the Id. Ideal Va = 2 V 2 kn RL 10 kn VL Solution:
A single phase bridge rectifier supplied from a 120V - 50 Hz sinusoidal source is connected to an inductive load. The general expression of the RMS AC component of the current is given below where Vm is the maximum input voltage. If R = 1k2, then the value of the inductance that would limit the AC component IAc to less than 5% of the DC component Ipc would be equal to: 4Vm IAC V2. 1. R2 + (2wL)? Select one: O a. 4.92H Ob. 11.92H O c. 8.92H O d. 14.92H TOSHIBA 24
A thermistor is placed in a 200°C environment and its resistance measured as 30000Q. The material constant B is 3627°K. If the thermistor is then used to measure a particular temperature and its resistance is measured as 6002. The thermistor temperature in °C. Select one: O a. 573 Ob. 255 OC. 692.64 d. 965.64
Q2 (a) Figure Q2(a) shows a clipper circuit made with a gemanium diode. Given the voltage input, Vin = 20 Vp-p, VDc = 5 V, Rs = 10N and RL=1 kN. (i) Sketch the full cycle of input voltage, Vin(t) in sinusoidal waveform. (ii) Determine the output voltage values for all input values. Show all the calculations and support your answers with the aid of diagram. R. Vin Si Ge R VOUT Vpc Figure Q2(a)
A thermocouple which has an input of a temperature change, the output form isSelect one:a Resistanceb. Magnetic field c.Capacitance d. Displacemente. Currentf.Voltageg. Heat
Q2 (a) Figure Q2(a) shows a clipper circuit made with a germanium diode. Given the voltage input, Vin = 20 Vp-p, VDc = 5 V, Rs = 10 N and R1=1 kN. (i) Sketch the full cycle of input voltage, Vin(e) in sinusoidal waveform. (ii) Determine the output voltage values for all input values. Show all the calculations and support your answers with the aid of diagram. (iii) Sketch the overall output waveform, VoUT (1).- R. + Vin Si Ge R VOUT Vpc Figure Q2(a)
A three-phase rectifier is supplied by a 173.2-V rms line-to-line 60-Hz source. The RL load is a 100 resistor in series with a 15-mH inductor. Determine THD taking Is1 = 1.35
In the circuit below, we have a Zener Diode circuit with a load, RL. Use the same measurements for source voltage V1 and resistor R3 resistance as in the circuit schematic. V1 -15V R3 2700 D1 1N753A RL Determine the lowest possible value for the load RL, so that the voltage drop across it is equal to the Zener voltage. For your diode, use model Zener 1N753A. This diode has a Zener voltage of 6.2V, a Zener current of 60mA, a Zener impedence of 72, and a test current of 20mA.
A resistor and a capacitor are connected in series across a supply of 250 V. When the supply frequency is 50 Hz the current in the circuit is 5 A. When the supply frequency is 60 Hz, the current is 5.8 A. Find the value of the resistance. Ans: ___ ohms
400 V is the input voltage given to a chopper, the required output is 650 V. The thyristor is conducting 300 usec. what is the addition of conducting and non conducting period? (Write your answer in usec) Answer:
I. SOLVE THE FOLLONING PROBLENS : A COPPER WIRE OF 0,3 Mm RAAUS HAS A LEN ETH OF 1. JOM- IF THE RESISTIVITY of cOpPER IS 1-7 x0 WHAT WOULD BE THE RESISTANOE OF THE WIRE? OF A 100m WIRE IS 1035 mm AND 3.7 OHMS. WHAT 2. THE DIAMETER THE REISTANCE IS IS THE CONDUCTIVITY 3. WHAT WILL BE THE VALUE OF A CAPACITOR WHEN IT HAS A CAPACITIVE REACTANCE OF 300R ANP to A 6o HZ. SUPPLY? IN FARADS IS CONNECTED 4. WHAT Is THE VALUE OF THE RESISTOR WITH THE FOLLOWING COLORS ? A. BROWN, BLACK, GOLD, REP B. BLUE YELON BROWN, SILVER PED, SILVER, BROWN, VIOET C. 5. AND t WHEN V 220V AND R= 50n WHEN I = 45 A WHEN V = 120V FIND V ANO R 80n AND AND E= 11A-

SEE MORE QUESTIONS

Recommended textbooks for you

EBK ELECTRICAL WIRING RESIDENTIAL

Electrical Engineering

ISBN:

9781337516549

Author:

Simmons

Publisher:

CENGAGE LEARNING - CONSIGNMENT

EBK ELECTRICAL WIRING RESIDENTIAL

Electrical Engineering

ISBN:

9781337516549

Author:

Simmons

Publisher:

CENGAGE LEARNING - CONSIGNMENT

SEE MORE TEXTBOOKS