If crank OA rotates with an angular velocity of woOA A = 28 rad/s, if L;=0.4 m, and L2= 1.8 m. Determine ( Fill at the instant shown, the magnitude without direction or units ) 1- Velocity of point A VA (m/s) 2-Angular velocity of rod AB WAB (rad/s) 3- The velocity of piston B Vg (m/s)

If crank OA rotates with an angular velocity of woOA A = 28 rad/s, if L;=0.4 m, and L2= 1.8 m. Determine ( Fill at the instant shown, the magnitude without direction or units ) 1- Velocity of point A VA (m/s) 2-Angular velocity of rod AB WAB (rad/s) 3- The velocity of piston B Vg (m/s)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The link AO has a 3 rad/sec angular velocity (in the clockwise direction). At the instant shown in the figure, determine the following: a) The angular velocity of link BC. b) The angular velocity of triangular plate ABD. c) The velocity magnitude and direction of point D. 3" -7"
If the rod BC rotates counter clockwise with an angular velocity wBc = 4 rad/s, determine the following: a) In the figure, which letter represents the IC point of rod AB. b) The magnitude and direction of the angular velocity of rod AB (wAB). c) The magnitude and direction of the velocity of point E, Vg. F G 0.4 m 0.4 m 0.2 m E Wac4 rad/s (Hint: Use the IC method, else the answers will not be reviewed). In the figure, which letter represents the IC point of rod AB. H The magnitude of the angular velocity of rod AB (WAB). 4 rad/s The direction of the angular velocity of rod AB (WAB). CCW The maanitude of the velocity of point E V-
For the instant represented, when crank OA passes the horizontal position. Crank OA has a uniform clockwise angular velocity 4.9 rad/s. 1- Speed of A (m/s) 2- Speed of B (m/s) 3- Angular velocity of AB (rad/s)
Q2 -1- For the mechanism shown determine for all moving points. A -The number of degrees of freedom. B-Velocity diagram. C- Acceleration diagram. D-The number of instantaneous center. (45°) AB=40mm, BC=120mm, w=12rad/s., ø= 1orod/s AB = 2 50mmn
Robert’s linkage is named after Richard Robert (1789–1864) and can be used to draw a close approximation to a straight line by locating a pen at point F. The distance AB is the same as BF, DF, and DE. The instant shown, bar AB has a constant angular velocity of 6 rad/s clockwise.a)Determine the angular acceleration of bar DE.b)Determine the angular acceleration of point F.
1. Shown below is a power hacksaw. At this instant, the electric motor rotates counterclockwise and drives the free end of the motor crank (point B) at a velocity of 12 in./s. Additionally, the crank is accelerating at a rate of 37 rad/s2. 15° 6" B 30° 1.75" (a) a. Draw the mechanism to scale. b. Draw the Velocity Polygon. Use Appropriate scale. c. Find the Relative Velocity of C with respect to B. d. Draw the Acceleration Polygon. e. Find the relative Acceleration of C with respect to B. f. Locate all the Instantaneous Centers.
Graphically, draw the entire acceleration polygon and use it to find both the magnitude and direction of a and ace at the instant shown. Also, find magnitude and direction of a2, a3 and 4 when a) The crank angular velocity w₁ is constant at 100 rad/sec CCW. b) The crank angular velocity w3 is 100 rad/sec CCW and accelerating at 25000 rad/sec² Velocity scale: 1 cm: 20 in/sec Acceleration scale: 1 cm: 4000 in/sec² B 0 0 = 45° 7 in 0₂C = 4 in O₂D = 6 in 0,03 = 6 in 2 in
Draw a six-bar linkage mechanism used for holding an industrial stirrer. Points A, B, and E are on a straight line on link 2. Points B, C, and G are on a straight line on link 3. The input link 2 rotates with a constant angular velocity a of 3 rad/s (cw) at the instant. O2=0 (a) Complete the acceleration polygon according to the drawing scale given, and find the angular accelerations Oy, 04, as, and as of links 3, 4, 5, and 6, and the acceleration Ap of point F. The position of link 2 is given as input. Write down the vector loop equations of the linkage for analytical position analysis and identify the unknowns in the equations. Note: Round off all your answers to two decimal places. Dimensions: AB= 40.00 mm BE = 20.00 mm BC = 33.54 mm CG= 33.54 mm CD = 18.03 mm EF = 43.00 mm FG = 29.15 mm
The link AO has a 3 rad/sec angular velocity (in the clockwise direction). At the instant shown in the figure, determine the following: 5" a) The angular velocity of link BC. b) The angular velocity of triangular plate ABD. c) The velocity magnitude and direction of point D. 7" WBC Choose... Direction of WBC is Choose... WABD= Choose... Direction of WABD is Choose... VD= Choose... The angle of VD with respect to the Choose... positive x-axis is
7) At the instant shown the angular velocity of link AB is 4.5 rad/sec in the CCW sense. Determine a) the angular velocity of link ED (magnitude and sense), b) the angular velocity of link BD (magnitude and sense), c) velocity vector of point D. Answers: y 250 mm D 200 mm 150 mm E WED = 8kr/s WBD = =-4.8kr/s ▼D = VB +☎BD×ĪDI B = −900i +|- 4.8k|× 250ī = -9007-1200j mm/sec
UPVOTE will be given! Please write the complete solutions legibly. No long explanation needed. Answer in 2 decimal places. Dynamics of Rigid Bodies A particle moves that is defined by the parametric equations given below (where x and y are in meters, and t is in seconds). Solve the angular velocity (rad/s) at t = 2 seconds. x = 3t2 - 1 ; y = t3 - 3t2 + t - 3
Question 4- On the diagram 1. Draw velocity vector of B 2. Find magnitude of linear velocity of B 3. Draw velocity vector of C 4. Find IC instantaneous centre of rotation for CB (clearly indicate perpendicular directions where applicable) 200 mm 150 mm 30° B @AB=4 rad/s 60°