If the cable in Figure ran for the whole of its length, grouped with others of the same size in a high ambient temperature, and was totally surrounded with thermal insulation, The correction factors considered will be----------- Fuseboard High ambient temperature Cable Grouping of cables Thermal insulation Load BS 3036 fuse O a. Cg O b. All Ca,Cg.Ci and Cf O c. Ci O d. Ca

If the cable in Figure ran for the whole of its length, grouped with others of the same size in a high ambient temperature, and was totally surrounded with thermal insulation, The correction factors considered will be----------- Fuseboard High ambient temperature Cable Grouping of cables Thermal insulation Load BS 3036 fuse O a. Cg O b. All Ca,Cg.Ci and Cf O c. Ci O d. Ca

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter20: Special-purpose Outlets For Ranges, Counter-mounted Cooking Unit , And Wall-mounted Oven

Section20.2: Wall-mounted Oven Circuit And Free-standing Range

Problem 14R

See similar textbooks

Similar questions

Most residential general lighting circuits are wired with 14-AWG copper conductors and are protected by 15-amp circuit breakers. However, there are many electricians who install 12-AWG copper conductors and protect them with 20-amp circuit breakers. How will you know which conductor size and which circuit breaker size will be used for the general lighting branch circuits in the house you are wiring?
h.1. In an alternating-current system, the maximum size for a copper grounding electrode conductor isA. 250 kcmil.B. 3/0.C. 500 kcmil.D. 4/0. h.2. The figure shows a fault condition in an ungrounded electrical system. Which of the following will occurbecause of the fault in this system?A. Only the overcurrent protector at Point A will trip open.B. The ground fault will heavily damage the service.C. Nothing will happen until a second ground fault occurs.D. The overcurrent protection will trip, shutting off all the line side power.
12 - Due to the effect of the resistance of the cable connected to RTD, two-wire cables up to ……. meters and three-wire cables up to ……... meters are used in standard designs. A) 10-150B) 40-500C) 50-195D) 30-230E) 200-1000
We are running 3 wires and a ground in a RMC to a control panel with a 60 amp circuit breaker disconnect in the control panel. The conduit is run along the ceiling where the ambient air temperature is 100 degrees. The control panel feeds our secondary cooling pump. What size are the ungrounded conductors? All conductors have typeTHHN insulation. A #6 AWG B 600 Kcmil C #8 AWG D #2 AWG What size RMC do we need? A 3" B 3/4" C 1" D 1 1/2"
QUESTION 5 We would like to run the power wires for both cooling pumps in the same RMC from the Breaker panel to a junction box above the control panel. What size ungrounded conductors do we need for the 100 amp load? All conductors have typeTHHN insulation. A #6 AWG B #3 AWG C #4 AWG D #1 AWG
3. The zero sequence current is times the current in neutral wire.
70. A circuit supplies a continuous load of 38 amperes and is protected by a 50-amperecircuit breaker. All conductor terminations in the circuit are rated at 75°C. If the circuit conductors are THWN copper, determine the minimum size permitted for the circuit. A. 60 A B. 50 A C. 40 A D. 70 A
How are series circuits used in air-conditioning equipment?
Six 1/0 aluminum conductors are to be run in a conduit. Each conductor has type THWN insulation's, and the ambient air temperature is 30 degrees celcius. What is the ampacity of each conductor?
5) The Murray Loop Test figuer shown below is used to locate ground fault in a telephone communication cable. The total resistance, R = R₁ + R₂ is measured by Wheatstone Bridge and it is equal to 60092. The conditions for Murray Loop Test are as follow: R3 = 2k2 and R4 = 1kQ2. Determine the location of the ground fault in meter and define it from which point, if the length per Ohm = 80m. Power or communication cable Short circuit fault Murray Loop Test H|H"
Load in Figure 1 needs to be connected to Mains Switch Board (MSB) using multicore PVC cable. As a maintenance engineer, you need to proposed cable size for the load, Determine the following issues. 1) Calculate current demand for the circuit. 1) Detemine suitable MCCB (Model and nominal current rating) should be used to protect the load against over-current. im Propose suitable cable size for the load in Figure 1. iv) Calculate voltage drop of the proposed cable WITHOUT consider the cable reactance and voltage drop correction due to higher cable operating temperature v) Calculate voltage drop of the proposed cable BY consider the cable reactance and voltage drop correction due to higher cable operatıng temperature vi) If the multicore PVC eable is change into 3 single core PVC cables, what the suitable cable size. All other multicore cables not available. (25 + variable x) m (A) 30 m (B) (15 + variable b) m (C) Multicore PVC cable MCCB 95 kW. (400 + variable y) V. 0.85 p.f. Load MSB…
For loop ACDBA, what is the total voltage with 30 V for V1 , 90 V for V5 , 120 V for V3 and including 240 V applied voltage?