If the equivalent length of a g0' elbow is greater than the 45 elbow, the pressure loss across the go' elbow is ---- the 45 elbow.Oa Greater thanOb: Lesser thanOc Same asOd None of theseFor hydraulically smooth pipe, the resistance to flow depends only on the?O a Relative roughnessOb: Absolute roughnessOc Reynolds numberOd Relative roughness and Reynolds number

Answered: Image /qna-images/answer/b73f586a-e49d-49dc-8ae9-87d64822f381.jpg

If the equivalent length of a g0' elbow is greater than the 45' elbow, the pressure loss across the go' elbow is. O a Greater than Ob: Lesser than Oc Same as Od. None of these ----- the 45' elbow. For hydraulically smooth pipe, the resistance to flow depends only on the? O a Relative roughness Ob: Absolute roughness Oc Reynolds number

If the equivalent length of a g0' elbow is greater than the 45' elbow, the pressure loss across the go' elbow is. O a Greater than Ob: Lesser than Oc Same as Od. None of these ----- the 45' elbow. For hydraulically smooth pipe, the resistance to flow depends only on the? O a Relative roughness Ob: Absolute roughness Oc Reynolds number

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q-The flow of water (mass density - 1000 kg/m³) and kinematic viscosity = 106 m² /sec, a compressible pipe with equivalent roughness Ks as 0.12mm yields average shear stress at the pipe boundary = 600N/m². The value of Ks/8' (8' being the thickness of laminar sublayer) for this pipe is ...
What will be the nature of surface of pipe if the flow of water is taking place having roughness size (k) = 0.10mm, yields an average shear stress at pipe boundary To 250N/m², take v = 10-6m²/sec A Hydrodynamically smooth B Hydrodynamically rough C In transition zone D Data insufficient II
The flow of water (mass density - 1000 kg/m³) and kinematic viscosity = 10-6 m²/sec, a compressible pipe with equivalent roughness Ks as 0.12 mm yields average shear stress at the pipe boundary = 600N/m². The value of K5/8' (8' being the thickness of laminar sublayer) for this pipe is...
2. WHAT IS THE MAXIMUM Pt Ре ↓ O O O 20 dia mm BEARING STRESS : 100 MPa SHEAR STRESS: 150 MPa STRESS: 280 MPa SAFE LOTAD? 130mm ->P I -P 25mm
the pipe? [-2. A steel pipeline with a nominal diameter of 24 in has an ID of 22.624 in (575 mm) and a wall thickness of 0.688 in (17.5 mm) carries a flow of 28 ft3/s (794 L/s). The pipe makes a short-radius 90° turn. What is the force developed in a buttress at the bend? What stress would be developed in the pipe by this change in direction if no buttress were provided? -3. What is the maximum stress which could be produced in the pipe of Prob. 6-2 as a result of suddenly closing a valve in the line? (K for water is approximately 10 percent of the value of E for steel.) SoLve Prob (6-3) REFERENCES 1. John Parmokie
the pipe? [-2. A steel pipeline with a nominal diameter of 24 in has an ID of 22.624 in (575 mm) and a wall thickness of 0.688 in (17.5 mm) carries a flow of 28 ft3/s (794 L/s). The pipe makes a short-radius 90° turn. What is the force developed in a buttress at the bend? What stress would be developed in the pipe by this change in direction if no buttress were provided? -3. What is the maximum stress which could be produced in the pipe of Prob. 6-2 as a result of suddenly closing a valve in the line? (K for water is approximately 10 percent of the value of E for steel.) SoLve Prob (6-3) REFERENCES 1. John Parmaki
a. Determine the magnitude and direction of the hydrostatic force acting on the gate using PRESSURE PRISM CONCEPT. Illustrate and label the pressure diagram/prism as part of your solution. Express your answer in kips. b. Determine the magnitude and direction of the force exerted on the plate by the ridge. Illustrate and label the FBD of the force system. Express your answer in kips.
R-1.11 A pipe (E = 110 GPa) carries a P, = 120 kN at A and a u niformly distributed load P load %3D = 100 kN on the cap plate at B. Initial pipe diameters and thicknesses are d. = 38 mm, L, = 12 mm, 70 mm, and t, BC = 10 mm. Under loads P, and P,. wall thickness Iac increases by 0.0036 mm. Poisson's ratio v for the pipe aterial is approximatcly: (A) 0.27 (B) 0.30 (C) 0.31 (D) 0.34 Inc dnc Cap plate 11 A P1 P2
(47 H.WOA vod Con sists of three bars of unequal dlameters as shown in fig., find the Stress in each bar and the C longation of the rocd ? use E = 200G Va %3D Ø=4omm =30mm =20 mm 2.1W 60 1.5m 2.5m 2m
A rigid pipe OABC is subject to a force F = 60i + 75j - 30k (N) applied at point C and force P applied at point B. Assume a =0.4426 m B a 0.1 m
Problem 2 The steel water pipe has an inner radius of 6 in and wall thickness 0.25 in. (1) If the valve A is open and the flowing water is under a gauge pressure of 240 psi. Determine the longitudinal and hoop stress developed in the all of the pipe. (2) If the valve A is closed. Determine the longitudinal and hoop stress developed in the all of the pipe.
X Your answer is incorrect. The copper pipe [G - 7,000 ksi] has an outside diameter of 3.250 in. and a wall thickness of 0.250 in. The pipe is subjected to a uniformly distributed torque of t- 80 lb-ft/ft along its entire length. Using a - 2.0 ft, b- 3.5 ft, and c- 7.0 ft, determine (a) the maximum shear stress in the pipe. (b) the rotation angle oc at the free end of the shaft. B Answers: (a) Tmax- i 10080 ksi (b) oc - i 2045.71 rad