If we wish to regulate a bathroom shower temperature, where the input to the system is the ratio of cold-to-hot water, and accurate temperature control is important as well as minimal overshoot, which of the following controllers most suitable? O a. A Position Observer O b. An Acceleration Synthesizer O c. A Proportional-Derivative Controller, PD Od. An Integral Controller, I O e. A Proportional Controller, P Of.A Proportional-Integral-Derivative Controller, PID

If we wish to regulate a bathroom shower temperature, where the input to the system is the ratio of cold-to-hot water, and accurate temperature control is important as well as minimal overshoot, which of the following controllers most suitable? O a. A Position Observer O b. An Acceleration Synthesizer O c. A Proportional-Derivative Controller, PD Od. An Integral Controller, I O e. A Proportional Controller, P Of.A Proportional-Integral-Derivative Controller, PID

Understanding Motor Controls

4th Edition

ISBN:9781337798686

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter54: The Operational Amplifier

Section: Chapter Questions

Problem 7RQ: Name two effects of negative feedback.

See similar textbooks

Similar questions

Q: Discuss the control system (the level controller and the temperature controllers) shown in figure (2). Specify the controlled and manipulated variable in each case. Discuss the type of the controller used in each case, that is, a simple feedback controller, a feedforward controller, a cascade controller, etc. Draw the block diagram of the temperature control loops. Feed Reactor temperature set point (master) TC Water surge tank i Jacket itemperature i set point (slave) TC LC-LT Reactor Cooling water out Product Cooling water makeup Circulation pump Figure (2)
Please
1. Give an example of open loop and closed loop system (one example each). Also state the input, control system, feedback and output parameter. Example. 1. Open Loop - Water Heater: Input - Water Temperature (Cold) System - Heating Element Output - Water Temperature (Hot) 2. Closed Loop - Air-conditioning System Input - Desired Room Temperature Control - Motor controller/Compressor/ACU Feedback - Temperature Sensing Output - Room Temperature
(PID solution with the requirements and simple explanation. Thx) INSTRUCTION: Given three bare processes develop a control system using feedbackand feedforward concept/principle. Your output is a process and instrumentationdiagram (P & ID) using ISA's Instrument Identification and Symbols standards withexplanation. PROCESS 2: The liquid level inside the tank is regulated at a value of 3.0 m on a condition ofcontinuous liquid inflow and outflow. Requirements: Two feedback solutions One feedforward solution
block diagram pls solve fast As Simplify the multiple loop feedback control system? R(s) G₁ G₂ H3 H₂ + G3 H₁ G₁ Y(s)
EXPERIMENT TITLE : PID CONTROLLER IN LEVEL CONTROL SYSTEM OBJECTIVE:To demonstrate the characteristic of P,PI and PID controller response on a level controller system. Based on the topic and objective given,please make a clear introduction.
QUESTION 3 An open loop transfer function with a unitary feedback control system is given K by G(s) =- where K is the gain of the system. An open loop (s+1)(s+4) transfer function with a PID controller must be designed in order to yield a peak time of 1.047 s, and a damping ratio of 0.8. 3.1. Calculate the design point s, of the system 3.2. Calculate the gain and the zero(s) of the PID controller 3.3. Provide the block diagram of the compensated system with the PID controller
The temperature of a catalysed exothermic reaction is being maintained at T1°C as it promotes generation of a particular product. It is proposed to control the temperature with a proportional only controller of gain Kc. The temperature dynamics of the reactor can be modelled as a mixture of a CSTR (1st order) and PFR (dead time) to changes either in inlet temperature, or in the heating/cooling jacket flowrate via Ke-tas Ts+1 i) Considering a change in inlet temperature show why a 1st order model for a CSTR and a dead time model for a PFR are appropriate. CSTR - continuous stirred tank reactor PFR - plug flow reactor
For a unity negative feedback control system having an open-loop transfer function, G(s) as given below. Find out the value of "K" such that the system will be in the stable region. (K/s) (s3 + 12. 5s2 + 50. 5s + 66) G(s) =
Which type of the system is illustrated in Figure Pressiure Velocity Torque Comparator Controller Process Velocity 15- Мeasmement O A) Closed-loop system with multiple input and single output B) Open-loop system with single input and single output C) Closed-loop system with single input and single output O D) Open-loop system with single input and multiple output E) Closed-loop system with single input and multiple output
3. Sketch a house's heating system which containing a gas furnace that heats water which circulates to radiators on the walls, and a thermometer that is connected to a control module that can turn the furnace on or off. The outside temperate is Text, the inside temperature is T, and the desired temperature is Ta. Describe the elements of the feedback control loop.
Q-1 A characteristic equation of a feedback control system is (s3 + 3s2 + 6s + 25 = 0 ), %3D 1. Cheack the stability of the system by Routh method. 2. Number of the root that is in right side , if its exist.