Impedances. In alternating current, the resonance frequency is defined as the frequency that would make the effect of the reactive elements eliminate each other in a circuit, so that the effect of the impedance would be purely resistive, and the maximum active power. Knowing the above, calculate the resonance frequency of the following circuit, then with that frequency calculate the equivalent impedance seen by the source and verify that the circuit is purely resistive. 20 N 2 H VF N 100 μF 100 kn 4Ω.

Impedances. In alternating current, the resonance frequency is defined as the frequency that would make the effect of the reactive elements eliminate each other in a circuit, so that the effect of the impedance would be purely resistive, and the maximum active power. Knowing the above, calculate the resonance frequency of the following circuit, then with that frequency calculate the equivalent impedance seen by the source and verify that the circuit is purely resistive. 20 N 2 H VF N 100 μF 100 kn 4Ω.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q2. For the circuit shown below, sketch i, & Vo 60 a. Find the conduction angle of the thyristor. b. Find the average output voltage V. R-6.50 f- Go Hz = 27AL = 120x17X10 = 6.4092 075 LO = RrjX= Vo L-17mH 6.5+j6.469=9.128 (44595 075 75V( Es 24 Vm A e
(b) Draw the circuit diagram of step-down chopper, also draw the waveforms of source voltage Vs and output voltage V. for duty ratio a = 0•4 and time period T = 10 us.
Show the capacitors, whether it is effective at low or high frequencsies Draw low frequency small-signal-equivalent circuit. AND LOWER corner is 82Hz frequency. Design the circuit. Draw the high frequency small-signal-equivalent circuit. AND UP-CORNER İS 172Hz frequency. DESİGN THE CIRCUIT.
Design a boost converter to provide an output voltage of 36V from a 24V source. The load is 50W. The voltage ripple factor must be less than 0.5%. Specify the duty cycle ratio, switching frequency, inductor and capacitor size, and power device
Sketch the voltage signal v=3cos(5t -20°). Also, determine the peak value, peak-to-peak value, frequency and phase
Explain what each component is in the design below: DD 7Ro PQ5 8Eo DD 9 So 10 - type of circuit? 1. 6. 2. 7. 3. 8. 4. 9. 5. 10. CO
Q.) Do parts d ,e and f. Resonent frequency 1612 hz
2. The circuit given below is using a transformer of 230V/30V. The load resistance is 10KS. Find Vin (rms and peak values), Vdiode and VLOAD (Peak and dc values). Draw the input and output voltage waveforms. (Si diode) Vin: Vin rms= Vin peak = VDIODE Vdiode = 4 Vin VLOAD: VLOAD Peak =. Load VLOAD VLOAD DC= 2031 Supply wwwwww
H.W: A resistor of resistance R=1000 2is maintained at 17 °C and it shunted by 100 uH inductor. Determine the ms noise voltage across the inductor over a frequency bandwi dth of: Ans: 182 x10° volt Ans: 9.22 x10 volt Ans: 2.34 x10 volt i) 15.9 kHz ii) i) 159 kHz 1590 kHz
Buck Converter Design Power supplies for telecommunications applications may require high currents at low voltages. Design a buck converter that has an input voltage of 3.3 V and an output voltageof 1.2 V. The output current varies between 4 and 6 A. The output voltage ripple mustnot exceed 2 percent. Specify the inductor value such that the peak-to-peak variation in inductor current does not exceed 40 percent of the average value. Determine the required rms current rating of the inductor and of the capacitor. Determine the maximum equivalentseries resistance of the capacitor.
4- Design a boost converter that will have an output of 60 V from a 24-V source. Design for continuous inductor current and an output ripple voltage of less than one percent. The load is a resistance of 50 2. Assume ideal components for this design. VL ooooo ip - ^
A step up dc/dc converter has input voltage Vs = 9 V, the average output voltage Va = 15 average load current la = 0.8 A. The switching frequency is f = 20 kHz, inductance is L = 0.3 mH and the parallel capacitance is C = 0.44 mF. Which one is the ripple current of inductor, Al ?