In a dry cutting operation using a -5 degree rake angle, the measured forces were; cutting force = 1330 n and thrust force = 740 n. when a cutting fluid was used, these forces were; cutting force = 1200 n and thrust force = 710 n. what is the change in the friction angle resulting from the use of a cutting fluid? 10:40 AM/

In a dry cutting operation using a -5 degree rake angle, the measured forces were; cutting force = 1330 n and thrust force = 740 n. when a cutting fluid was used, these forces were; cutting force = 1200 n and thrust force = 710 n. what is the change in the friction angle resulting from the use of a cutting fluid? 10:40 AM/

Precision Machining Technology (MindTap Course List)

2nd Edition

ISBN:9781285444543

Author:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Publisher:Peter J. Hoffman, Eric S. Hopewell, Brian Janes

Chapter5: Turning

Section5.4: Manual Lathe Threading

Problem 8RQ: What is the name for the rotating device that transmits power to the carriage for thread-cutting...

See similar textbooks

Similar questions

Q1. The part shown below will be turned in two machining steps. In the first step a length of (50 + 50) = 100 mm will be reduced from Ø100 mm to Ø80 mm and in the second step a length of 50 mm will be reduced from Ø80 mm to Ø60 mm. Calculate the required total machining time T with the following cutting conditions: Cutting speed V=80 m/min, Feed is f=0.8 mm/rev, Depth of cut 3 mm per pass. Ø100 Ø80 Ø60 50 50
2) In an orthogonal cutting operation, the cutting tool has a rake angle = 20°. The chip thickness before the cut = 0.25 mm. If the cutting force and thrust force are measured during an orthogonal cutting operation with values, Fc = 1450 N and Ft = 1990 N. The width of the orthogonal cutting operation w = 2.5 mm. the friction angle B is = 79.91° Determine: The Shear Angle The Shear Strain The Shear Strength of the material The Force of Friction
QUESTION 5 Determine the spindle speed (rpm), the feed rate (in/min) and the cutting power required for turning a 1º diameter copper rod with a depth of cut of 0.1" using a cemented carbide tool. O N=287 RPM, F-25.8 in/min, P=9.7 hp ON=2866 RPM, F=258 in/min, P=97 hp ON=1146 RPM, F-25.8 in/min, P=97 hp O N= 11460 RPM, F-340 in/min, P=130 hp ON= 1146 RPM, F-34 inimin, P= 13 hp ON= 115 RPM, F-3.4 in/min, P=1.3 hp QUESTION 6 It is required to face mill an aluminum block to size it down from 2" to 1.5" thick using a 3" diameter 2-toothed carbide cutting tool. The block is 6.0" wide and 6" long. The entire tool diameter engages the workpiece during the cut. Calculate the recommended spindle speed in revolutions per minute, feed per tooth, and cutting power required. O N=1529 RPM, f= 0.026 in/rev/tooth, P = 36 hp O N-3820 RPM, f= 26 in/revitooth, P=27 hp O N-3820 RPM, f= 0.052 in/rew/tooth, P=27 hp ON-382 RPM, F= 0.026 in/revitooth, P = 0.027 hp O N-3820 RPM, f= 0.052 in/rev/tooth, P=2.7 hp…
Using the formula (below), calculate the revolutions per minute (rpm) a drill press spindle should rotate using a Ø1⁄2 HSS twist drill if the cutting speed will be 90 surface feet per minute, SPM?N~[4xV]÷DN = _____________________________________________ RPM’s
The surface finish specification in a turning job is 0.90 um. The work material is cast iron. The cutting conditions have been selected as follows: v =90 m/min, f -0.23 mm/rev, and d = 2.2 mm. The nose radius of the cutting tool must be selected. Determine the minimum nose radius that will obtain the specified finish in this operation. oichie 0 90. m The wok matedal i material is
In crank and slotted lever quick return mechanism, the crank length is (100 +X )mm and the distance between the fixed center is (225+X)mm. The length of the slotted lever is (525+X)mm. Determine the ration of time of cutting stroke to time of return stroke. Also calculate the length of the stroke . Note where X is two digit number made from the last two digit of the registration number of the students For example if the reg. no. of the student is 11912081 then X=81 and crank length is 80+81=161mm Draw the neat and clean diagram with proper scale. Rough drawings will not be considered
Q4-/A/ During orthogonal cutting operation of material has shear strength 95.5 Mpa. The cutting force is more than thrust force by 10%. The rake angle = 5°, the width of the cut = 5.0 mm, the chip thickness before the cut = 0.6, and the chip thickness ratio = 0.38. Determine (a) both cutting force and thrust force and (b) the coefficient of friction in the operation.
The following data was obtained from an orthogonal cutting test. Rake angle = 20° Depth of cut = 6 mm Feed rate = 0.25 mm/rev Cutting speed = 0.6 m/s Chip length before cutting = 29.4 mm Vertical cutting force = 1050 N Horizontal cutting force = 630 N Chip length after cutting = 12.9 mm Using Merchant's analysis, calculate (a) Magnitude of resultant force, (b) shear plane angle, (c) friction force and friction angle, and (d) various energies consumed.
Answer the following questions by circling True or False. 9. Ceramics are the hardest tool materials in the world. 10. The smaller the cutting ratio, the larger the cutting deformation. 11. A shaper can be used for maching flat surfaces in horizontal and angular directions. 12. During the return stroke of the shaper, the cutting tool will simply be sliding... 13. The cutting speed of the hydraulic shaper changes throughout most of the cutting stroke. 14. Arbour-mounted cutters are used in vertical axis machines to generate flat surfaces... 15. Dividing head is an important attachment that is used to divide the periphery of the workpiece into a number of divisions to machine surfaces.. () () ()
Question 4. The following data are available from orthogonal cutting experiments. The depth of cut (feed) to = 0.13 mm, width of cut b = 2.5 mm, rake angle a = - 5°, and cutting speed V = 2 m/s. Chip thickness, t. (mm) = 0.23 Cutting force, F. (N) = 430 Thrust force, F; (N) = 280 Determine the shear angle ð, friction coefficient u , shear stress t, shear strain y on the shear plane, chip velocity Ve, and shear velocity Vs, as well as energies uf ,Ug, and u
Complete the side view of the BELT PULLEY in half section. Indicate the proper cutting-plane. ]] 44 1.1 H 14 1 H T 1.1.
Turning Operation In a production turning operation, the foreman has decreed that a single pass must be completed on the cylindrical workpiece in 4.8 min. The piece is 400 mm long and 150 mm in diameter. Using a feed = 0.43 mm/rev and a depth of cut = 4.0 mm, what cutting speed must be used to meet this machining time requirement? Hint: Re-arrange the Tm equation to find v in m/min Tm= T.DO.L v.f 1.522