In a procedure to evaluate the strength of the tri- ceps muscle, a person pushes down on a load cell with the palm of his hand as indicated in the figure. If the load-cell reading is 160 N, determine the ver- tical tensile force F generated by the triceps muscle. The mass of the lower arm is 1.5 kg with mass cen- ter at G. State any assumptions. Humerus Triceps Ulna Hand 150 mm- -150 mm→ Load cell 25 mm

In a procedure to evaluate the strength of the tri- ceps muscle, a person pushes down on a load cell with the palm of his hand as indicated in the figure. If the load-cell reading is 160 N, determine the ver- tical tensile force F generated by the triceps muscle. The mass of the lower arm is 1.5 kg with mass cen- ter at G. State any assumptions. Humerus Triceps Ulna Hand 150 mm- -150 mm→ Load cell 25 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Humerus Triceps Ulna Hand G 6" 6" Load cell 1" In a procedure to evaluate the strength of the triceps muscle, a person pushes down a load cell with the palm of his hand as indicated in the figure. If the load cell reading is 34.72 Ibf, determine the vertical tensile for F generated by the triceps muscle. The lower arm weighs 3.08 lbf with mass center at G. State any assumptions.
Compound axial member ABC has a uniform diameter of d-2.4 in. Segment (1) is an aluminum [E₁ - 10,000 ksi] alloy and segment (2) is a copper [E₂ - 17,000 ksi] alloy. The lengths of segments (1) and (2) are L₁ - 78 in. and L₂ - 150 in., respectively. Determine the force P required to stretch compound member ABC by a total of 0.35 in. L₁ A Part 1 Aluminum Answer: A- B Save for Later Calculate the cross-sectional area of the compound member. L2 (2) Copper in.² C P Attempts: 0 of 1 used Submit Answer Part 2 The parts of this question must be completed in order. This part will be available when you complete the part above. Part 3 The parts of this question must be completed in order. This part will be available when you complete the part above.
N and Determine the force in cables N necessary to support the 12 kg traffic light shown in figure. (Hint: Please just enter the numerical value without any unit and use three significant digit only. For example if AB= XXX N then enter only XXX.) Answer. = 24 1.63// KSI. 12⁰ B
A ladder with a uniform cross-section has a length of 4.80-foot long. It weighs W Ib. It is arranged such that one end is on the ground and the other against a vertical wall. The angle of triction at all contact surtaces is 20 degrees. What is the value of the coefficient of triction? What is f, in terms of variable Na? What is the normal force at A in terms of variable W? Answer in three decimal places
A bar, 12 mm in diameter is acted upon by an axial load of 20 kN. The change in diameter is measured as 0.03 mm. DeterminePoisson’s ratioYoung’s modulusBulk modulus Assume modulus of rigidity as 80 GPa
Determine the force in each member of the loaded truss. The forces are positive if in tension, negative if in compression. kys Part 1 B 3.1 m AD 50° CD Answers: AD = The Free-Body diagram for joint D is drawn assuming that all internal forces are in tension. Solve for the forces in AD and CD. The forces are positive if in tension, negative if in compression. 50 CD = i 6.2 m 50 D 50° 3600 N 3600 N N N
Question 2 Find the value of The reaction force at the support A. (X,XX,XXX represents the last digits number pf your IC) 4m 400 KN 10 m B 60 KN 4m 10 m. 157KN 4m 17 m D
Four 10 kg masses are being supported by an 800mm solid rod. The rod is being supported at both ends, and the rest of the rod is suspended. Determine the smallest rod diameter to support the masses without bending the rod. Assume the Tensile Strength of the Rod material is 500 MPa
The lengths of the members of the truss are shown. Figure 13 m 40 12 m 12 m 5m 13 m 1 of 1 Part A The mass of the suspended crate is 950 kg. Determine the axial forces in the members. (Figure 1) Enter your answers numerically separated by commas. FAB, FAC, FCD, FBC, FBD = Submit Provide Feedback Request Answer IVE ΑΣΦ IT vec Dad ? kN
The structure consists of a spring CD and a solid member ABC with a slot at B. The peg at B fits loosely into the slot at B and can hence be interpreted as a smooth support. The unstretched length of the spring is 80 mm. 50 mm 150 mm 50 mm A D C B k = 600 N/m 1.1 Draw separate free-body diagrams of member ABC and the spring CD. 1.2 Comment on the existence of two-force members and three-force members in this system. 1.3 Determine the reactions at A and B on the member ABC
A weight Wis dropped from a heighth on the mid-span at C of a simply-supported beam as shown, where the spring always remains vertical and is at its natural length when the beam is horizontal. For W-90 lb and the stiffness of the spring k-313 lb/in, determine the static elongation of the spring (apring). Le., h-0. [in] W 40" h 1"I
2-1. A standard steel specimen of in. dia- meter elongated 0.0087 in. in an 8 in. gage length when it was subjected to a tensile force of 6,250 lb. If the specimen was known to be in the elastic range, what is the elastic modulus of the steel? Ans: 29.3 x 106 psi.