In the figure below, the unbalanced wheel O has a mass of 30 kg and is connected to a 20 kg counter weight block, B, with a continuous cable. If a constant moment of 15 N-m is applied to the wheel in the clockwise direction. At the instance shown, the angular velocity, w, is 4 rad/s. The center of mass, G is 5 cm from the center and the wheel's radius of gyration is 7 cm (about center point O). Assume the pulley is mass-less and frictionless. M B 5 cm 5 cm Calculate the angular acceleration

In the figure below, the unbalanced wheel O has a mass of 30 kg and is connected to a 20 kg counter weight block, B, with a continuous cable. If a constant moment of 15 N-m is applied to the wheel in the clockwise direction. At the instance shown, the angular velocity, w, is 4 rad/s. The center of mass, G is 5 cm from the center and the wheel's radius of gyration is 7 cm (about center point O). Assume the pulley is mass-less and frictionless. M B 5 cm 5 cm Calculate the angular acceleration

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

SECW OM A motorbike wheel with an 8 kg mass has a 0.4 m radius of gyration around the z-axis, as shown in Figure. The wheel's shaft is supported by bearings A and B and rotates at a constant rate of 150 rpm in a counter-clockwise direction from the z-axis, while the frame rotates at 12 rpm in a counter- clockwise direction from the y-axis. Determine the resultant reaction forces at each bearing A and B due to the mass and gyroscopic effects. With the result of forces, which bearing has a tendency to fail first, which bearing should be considered for design purposes and explain the effect on motor if the bearing fail. y 0.55 0.4 All dimensions in meter (m)
A wheel is attached by a cable to a block The wheel has a radius of 2ft and weighs 300lbs, the block weights 20lbs. If the radius of gyration about the point of rotation of the disk is 1.5ft, how many revolutions will it take for the wheel to come to a stop assuming it was moving at 10 rad/s CW. Assume the block is on the left side of the wheel and thus causes a CCW moment.
The mass of flywheel of an engine is 8 tonnes and the radius of gyration is 1.8 metres. It is found from the turning moment diagram that the fluctuation of energy is 100 kN-m. If the mean speed of the engine is 150 r.p.m., find the maximum and minimum speeds.
The crankshaft of a vertical sıngle-cylinder engine, stroke 250 mm, rotates at 300 r/min The reciprocating parts ( including part of the connecting rod) have a mass of 100kg The connecting rod has a mass of 120 kg, it is 450 mm long, the centre of mass is 300 mm from the gudgeon pin axıs and the radiųs of gyration about the same axıs is 363 mm When the crank is 30° from the t dc position and moving downwards, determine 31 the side thrust on the cylınder walls due to the inertia of the reciprocatıng parts, and 32 the crankshaft torque on the crankshaft due to inertia
In the figure, the engine of a vehicle is shown as a representation.The crankshaft of the engine around the x-axis It rotates at 4000 rpm and its moment of inertia is 0.5 kgm2.Moving in the y direction, the vehicle enters the curve with a radius of 70 m at a speed of 120 km/h. In the meantime, find the moment coming to the motor bearings and interpret its effect on the vehicle.
A ring of mass m =1 kg and radius R = 1m is attached to a vertical shaft by means of a frictionless pin. Coordinates xyz are fixed to the ring as shown and the frictionless pin at A is aligned with the x-axis. The vertical shaft precesses about the Z-axis with constant angular velocity 2 = 1 rad/s. (a) At a particular moment when 0 = 30° and = 4 rad/s, find the value of Ö . This comes from a sum of the moments about the x-axis. Do not neglect gravity. (b) Find the torque or moment necessary that must be applied about the vertical shaft in order to keep it turning at a constant rate of N = 1 rad/s. Ring R XG A 1 Ixx = lyy =mR? G Iz = mR?
A shaft caries four rotating masses A, B, C and D which are completely balanced. The masses B, C and Dare 50kg, 80kg and 70kg respectively. The masses C and D make angles of 90° and 195° respectively with mass B in the same sense. The masses A, B, C and D are concentrated at radius 75mm,100mm,50mm and 90mmrespectively.The plane of rotation of masses B and C are 250mm apart. Determine the magnitude of mass A and its angular position the position of planes A and D.
A flywheel weight = 50 kN with radius of gyration= 1 m losses its speed from 400 rpm to 280 rpm in 5 minutes. Find change in angular momentum.
HW2 A uniform disc of 80 mm radius has a mass of 2000 g. It is mounted centrally in bearings that maintain its axle horizontally. The disc spins about its axle with a constant speed of 550 r.p.m. while the axle precesses uniformly about the vertical at 50 r.p.m. The directions of rotation are shown in the figure below. If the distance between the bearings is 130 mm, find the resultant reaction at each bearing due to the mass and gyroscopic effects. Ho +X +y * -y
An inside cylinder locomotive has its cylinder centre lines 1 m apart and has a stroke of 1 m. The rotating masses per cylinder are equivalent to 100 kg at the crank pin, and the reciprocating masses per cylinder to 200 kg. The wheel centre lines are 2 m apart. The cranks are at right angles. The whole of the rotating and 2/3 of the reciprocating masses are to be balanced by masses placed at a radius of 0.8 m. Find the magnitude of the balancing mass on the right most wheel. Select one: A. 55.32 kg B. 322.3 kg C. 225.3 kg D. 115.3 kg
(c) Four masses A, B, C and D are attached to a shaft and revolve in the same plane. The masses are 100 kg, 150 kg, 120 kg and 130 kg respectively and their radii of rotations are 225 mm, 175 mm, 250 mm and 300 mm. The angular position of the masses B, C and D are 45°, 120° and 255° from mass A. Find the magnitude and position of the balancing mass at a radius of 600 mm. Solve Analytically and verify it graphically
An inside cylinder locomotive has its cylinder centre lines 1 m apart and has a stroke of 1 m. The rotating masses per cylinder are equivalent to 200 kg at the crank pin, and the reciprocating masses per cylinder to 300 kg. The wheel centre lines are 2 m apart. The cranks are at right angles. The whole of the rotating and 2/3 of the reciprocating masses are to be balanced by masses placed at a radius of 0.8 m. Find the value of variation in tractive effort at 300 rpm. Select one: A. ±58476 N B. ±69780 N C. ±79654 N D. ±12475 N