In the figure shown below, the deflection of mercury is initially 208 mm. If the pressure at A is increased by 34 kPa, while maintaining the pressure at B constant, what will be the new mercury deflection?

In the figure shown below, the deflection of mercury is initially 208 mm. If the pressure at A is increased by 34 kPa, while maintaining the pressure at B constant, what will be the new mercury deflection?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What is the surface tension of benzene at 537-degree Rankine, if Y = 31.58 – 0.137T + 0.0001T^2? * O 28.2175 dynes/cm O 27.8224 dynes/cm O 21.6239 dynes/cm O No answer from the choices
After performing an experiment in a manner similar to the procedure described in the lab manual, it was determined that the best estimates, and corresponding errors, for height, mass of water, and slope of (mA) pairs are as follows: h= 153.0006 cm = 497.3100 g Mw = 0.006025 g slope = 7.14892 x 10- "C/g = 3.49901 x 107 "C/g %3D %3D = 0.04462 cm Satope 1. Using these measurements and eror estimates, calculate the specific heat of water, c. Show the correct formula and calculation. Then properly report your result. gh slope • M. 2 Satope sloper Cwexp Sewexp = Cwexp %3! 2. Perform a precision versus accuracy test using the accepted value for the specific heat of water, Cae Sewarp |Cwexp - Cacel
For a gage reading at A of -2.50psi, determine 1. The elevations of the liquids in the open piezomet er columns E, F, and G 2. The deflection of the mercury in the U-tube gage in the bottom part of the figure shown. El. 65.00P E F A G Air El, 49.00 ft † H -HL K sp gr 0.700 El, 38.00 t Water El. 26.00 t R sp gr 1.600 G EL, 20.00 hs El. 14.00 ft
Y = 9810 N m FH METHOD 1: Plane Surfaces METHOD 2: Curved Surfaces Fv TAKE NOTE: Use the 2 methods to solve the problem. COMPARE/DIFFERENTIATE THE TWO METHODS. Plane Surfaces F=? 45° gate width=1m 1m Curved Surfaces Directions: Guide Question/s: 1.) Using the procedure employed in calculating FH, F, and F in a curved surfaces, will it be applicable also in calculating the hydrostatic force F in an inclined rectangular gate?
6) Liquid in a closed container with ₁-1000 cm³ is under pressure p₁-1×10 N/m². Volume of the liquid is reduced to V₂=995 cm' when pressure increased to p=2×10 N/m². Calculate volumetric elasticity modulus of the liquid.
Numerical Analysis (HW. #1) The vertical stress increment (Ao) due to a point load acting on the surface of linearly elastic medium is given as: Ao = 3P23 27yr? +z? where P is the magnitude of the load, r is the lateral distance, and z is the depth of the point where the stress is to be calculated. If P = 10g kN andr = 1.5 m, determine (by using two methods: fixed-point and Newton-Raphson method) the depth z at which the stress increment Ao= 10n kN/m2. (Take g3student group number A=1, B=2, C=3, D=4, and E=5, n=10 ,and & =1x10-)
Q56 1. The stress concentration effect that leads to localized perforations in the stress distribution can occur in any situation where there are material discontinuities (True or Falto) 2. Is the theoretical geometric stress concentration factor of a hole plate determined based on the Liquid Area or the Full Area? 3. For the calculation of the maximum stress acting on the material it is necessary to define the coefficient of concentration of stress, which will be different depending on the area used (True or False) 4. The stress concentration factor in linear elastic materials depends on the charging mode, but is independent of its intensity (True or False) 5. In the case of a plate with a hole the use of the Full Area allows to find a minimum point what is important information for a project (True or False) 6. The stress concentration factor represents the level or distribution of voltage at the tip of a notch when it is reduced to a crack (True or False) 7. The proportionality…
9.2 (A). Determine the change in volume of a thin cylinder of original volume 65.5 x 10-'m' and length 1.3 m if its wall thickness is 6 mm and the internal pressure 14 bar (1.4 MN/m?). For the cylinder material E- 210GN/m2; v= 0.3. [17.5 x 10-m')
One end of a wire is attached to the ceiling. It has an elastic limit of 200 x 10^6 Pa. If it has a radius of 3.45mm, what is the maximum load (in kilograms) that can be hung on the other end before it breaks? (g = 9.8m/s^2) (round your answer to nearest whole number)
A rectangular plate 50 mm × 10 mm with a hole 10 mm diameter is subjected to an axial load of 10 kN. The notch sensivity is given as 0.76 , Taking theoretical stress concentration into account, find the actual stress concentration factor. O a. 2.14 O b. 4 О с. 3 O d. 1.8
The graph shown below shows the Modulus of Elasticity (E) of different materials with respect to temperature (°C). 240 210 170 140 100 -Carbon Steel, C < 0.3% -Nickel Steels, Ni 2% - 9% 70 Cr-Mo Steels, Cr 2%-3% Copper -Leaded Ni-Bronze -Nickel Alloys - Monel 400 35 -Titanium rengineeringtoolbox.com -Aluminium -300 -200 -100 100 300 400 500 600 700 800 Temperature (degc) a) Which material is the most ductile with increasing temperature? b) Which material is the least ductile with increasing temperature? c) Discuss the change in ductility (brittle / ductile behavior) occurring for different materials. Also, comment on why Young's modulus changes with temperature. E-modulus of elasticity (GPa)
A thick-wall underwater pipe is placed at 20m below sea level. The pipe is carryingcompressed natural gas with pressure of 50 MPa. The pipe has 115mm outer diameter andmade of 316 stainless steel with yield strength of 205 MPa. The density of sea water could betaken as 1029 kg/m3. Find out:a) What is the resultant outer pressure acting on the underwater pipe? b) What is the minimum inner diameter to ensure the pipe does not yield?c) Sketch the variation of hoop and radial stress across the pipe wall, completed with stresslabelling. d) What is the resultant longitudinal stress of the pipe?