Initially saturated water liquid at 200°C is contained in a piston-cylinder. The water is then heated isothermally until its volume is 100 times larger than its initial volume. 1. Determine the increase in energy (kJ/kg) of the water. 2. Determine the work transfer (kJ/kg) and indicate whether it is into or out of the system. 3. Determine the heat transfer (kJ/kg) and indicate whether it is into or out of the system. saturated water 2000 E

Initially saturated water liquid at 200°C is contained in a piston-cylinder. The water is then heated isothermally until its volume is 100 times larger than its initial volume. 1. Determine the increase in energy (kJ/kg) of the water. 2. Determine the work transfer (kJ/kg) and indicate whether it is into or out of the system. 3. Determine the heat transfer (kJ/kg) and indicate whether it is into or out of the system. saturated water 2000 E

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Skg of Steam at pressure of 4.9 bar is produ- ced from water at 20c. Determine the amount of heat supplied if the Steam is o.9 dy.
B2. The heat energy of 1605 kJ is supplied to saltwater in the steam generator to heat from 25°C to 104°C for the generation of water vapor, Take the density & specific heat of the solution as 1028 kg/m³ & 3 J/kg°K respectively. Determine the quantity of saltwater in the steam generator. I Solution: i) Change in Temperature (in K) ii) Mass of the saltwater (in kg) iii) Quantity (Volume) of salt water (in m³)
Question 1 A piston-cylinder assembly with a frictionless piston has a volume of 0.1 m' and initially filled with steam of 0.5 kg at a pressure of 0.4 MPa. There is heat transfer until the temperature reaches 573 K. Find the total heat transfer as well as the work done during the process. Sketch the process on a P-v diagram with respect to the vapour dome.
The rigid sealed vessel with a safety pressure valve, as shown, has a volume 0.8 m and contains 0.6 kg of water at 110 C, the vessel is now heated. At what pressure should the safety valve be set to have maximum temperature of 240 C in the vessel. safty valve Steam or vapor Liquid
A piston-cylinder arrangement contains water at 112°C, 84% quality with a volume of 0.98 L. What is the initial mass, in grams? The system is then heated, causing the 150-mm-diameter piston to rise and encounter a linear spring with k = 800 kN/m. Calculate the specific internal energy (kJ/kg) at this instant knowing that the measured volume is 1.65 L. The heating continues and compresses the spring in the process. When the piston encounters the stops, the pressure is 200 kPa. What is the temperature (in °C) and entropy (in J/K) at this point? Heating then continues until the pressure reaches 300 kPa. What is the volume, in L, at this instant? Illustrate the complete process in separate P-v and T-v diagrams.
A piston-cylinder device initially contains 0.8m3 of saturated water vapor at 250 kPa. At this state, the piston is resting on a set of stops, and the mass of the piston is such that a pressure of 300 kPa is required to move it. Heat is now slowly transferred to the steam until the volume doubles. a. Indicate knowns and unknows for each state as well as what type ofprocess is performed to get from one state to another. State anyassumptionsb. Determine the final temperaturec. Determine the work done during the processd. Show the process on a P-v diagram with respect to saturation linese. Determine the total heat transferred during this process
.A kilogram of Argon gas( MW= 40 kg/kmol, k=5/3) is in a piston cylinder set-up. Initially, it has pressure of 30kPa and volume of 0.2m3 and expanded to 20 kPa due to heat transfer. If the process is said to be isovolumic, find initial and final temperatures.
A piston-cylinder arrangement contains water at 110°C, 87% quality with a volume of 1 L. What is the initial mass, in grams? The system is then heated, causing the 150-mm- diameter piston to rise and encounter a linear spring with k = 800 kN/m. Calculate the specific internal energy (kJ/kg) at this instant knowing that the measured volume is 1.7 L. The heating continues and compresses the spring in the process. When the piston encounters the stops, the pressure is 200 kPa. What is the temperature (in °C) and entropy (in kJ/kg-K) at this point? Heating then continues until the pressure reaches 300 kPa. What is the volume, in L, at this instant? Illustrate the complete process in separate P-v and T-v diagrams. Hint: Draw the FBD of the piston in each state. wwwwwww D=0.15m H₂O
A piston-cylinder arrangement contains water at 110°C, 85% quality with a volume of 1 L. What is the initial mass, in grams? The system is heated, causing the 150-mm-diameter piston to rise and encounter a linear spring with k = 800 kN/m. Calculate the specific internal energy (kJ/kg) at this instant knowing that the measured volume is 1.65 L. The heating continues and compresses the spring in the process. When the piston encounters the stops, the pressure is 200 kPa. What is the temperature (in °C) and entropy (in J/K) at this point? Heating continues until the pressure reached 300 kPa. What is the volume, in L at this instant? Illustrate the process in separate P-v and T-v diagram. Note:1000 L = 1m3. Hint: Draw the FBD of the piston in each state.
1.A piston-cylinder containing air expands at a constant pressure of 150 KPa from a temperature of 285 K to a temperature of 550K.The mass of air in the cylinder is .05 Kg. Determine the system heat and work for the process
Q/ A dry gas reservoir is initially at an average pressure of 5500 psia and temperature of 145F. The gas has a gravity 0.67. What will the average reservoir pressure be when 40% of the original gas(in Scf) has been remained in the reservoir. Assume the volume occupied by the gas in the reservoir remains constant. If the reservoir originally contained 1MM cuft of reservoir gas, how much gas has been produced at a final reservoir pressure of 600 psia.
How many kilograms of -5 °C ice per day will melt and evaporate to steam after adding a total of 7500 kJ/hr?