InsideDiameter56 cm58 mm58 mmPassNumberof Tubes1 st12 nd383 rd30Crown Sheet CoverTrue Value = 503 ft²fill up the tableOutside Length HeatingDiameteSurfacer62 cm273 cm64 mm298 cm64 mm304 cm151 cmExperimental Value =Per Cent Error =

Answered: Image /qna-images/answer/dbd74a43-de14-414d-a346-9a08d07b8fdd.jpg

Inside Outside Length Heating Diamete Diamete Surface r r 56 cm 62 cm 273 cm 58 mm 64 mm 298 cm 58 mm 64 mm 304 cm 151 cm Experimental Value = Pass Number of Tubes 1 st 1 2 nd 38 3 rd 30 Crown Sheet Cover True Value = 503 ft² Per Cent Error =

Inside Outside Length Heating Diamete Diamete Surface r r 56 cm 62 cm 273 cm 58 mm 64 mm 298 cm 58 mm 64 mm 304 cm 151 cm Experimental Value = Pass Number of Tubes 1 st 1 2 nd 38 3 rd 30 Crown Sheet Cover True Value = 503 ft² Per Cent Error =

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

7. Calculate the minimum wall thickness between the inside diameter and datum feature B shown in the figure below. Datum B @ LMC: minus I. D. @ LMC: -Ø. minus Tolerance @ LMC: - Ø = The wall thickness equals half of the differences in diameters = Ø2.500 .020 4.059 ±.003 Ø2.000 .020 0.0200 ABO B I A Unless Otherwise Specified: .XXX = .010 ANGLES = ± 1° Figure for Problem 7
antuitive methodology (seize and fox) noting they will be different. olowing cases, find the degrees-of-freedom using KMOGE (Identify L. h. Jz and M) and using the em 3: KMOGE has conditions under which it simply produces the wrong answer. In each of the A. L= Mseize and Fix B L = MKMOGE = Mseize and Fix J = MEMOGE Msetze and Fix
uonsanh 9m A marine engine cylinder has a compression ratio (r) of 9.5, a clearance volume of 650 cm3 and a piston stroke length of 675 mm. What is the bore diameter in millimetres (mm) for the engine cylinder. Give your answer to the nearest millimetre mm.
I am not entierly sure where I when wrong here but I ended up getting 38.188lbs as an incorrect answer. I am pretty confident in my meathod I just belive I made an algibraic error. Could you solve this for me? thank you so much.
The plot below of load vs. extension was obtained using a specimen (shown in the following figure) of an alloy remarkably similar to the aluminum-killed steel found in automotive fenders, hoods, etc. The crosshead speed, v, was 3.3x104 inch/second. The extension was measured using a 2" extensometer as shown (G). Eight points on the plastic part of the curve have been digitized for you. Use these points to help answer the following questions. 1. 900 800 (0.10, 630 ) 700 (0.50, 745) (0.30, 729) 600 (0.20, 699) (0.40, 741.5) 500- (0.004, 458) (0.80, 440 ) - 400 (0.0018, 405) 300 D= 3.3 " 0.03" 200 G=2.0" 100 - 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 Extension, inches a. Determine the following quamtities. Do not neglect to include proper units in your answer. Young's Modulus Total elongation Yield stress Ultimate tensile strength Uniform elongation Engineering strain rate Post-uniform elongation b. Construct a table with the following headings, left-to-right: Extension, load, engineering strain,…
3. Find VR and Vc AO2=30mm В AB=60mm AC=80mm BC=45mm A B04=50mm 0,= 2 rad/s 0204=70mm 04 O4 Angle of 02A is 45 degrees with respect to positive x-axis.Drawing is not in scale redraw if possible and applicable.
7. Calculate the minimum wall thickness between the inside diameter and datum feature B shown in the figure below. Datum B @ LMC: Ø -Ø minus I. D. @ LMC: minus Tolerance @ LMC: - Ø. = The wall thickness equals half of the differences in diameters = Ø2.500 .020 4.059 +.003 Ø2.000 .020 +0.0200 ABO B A Unless otherwise Specified: .XXX= .010 ANGLES = ± 1°
already answered in bartleby. please do not copy! STATICS OF RIGID BODIES (UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS AND FBD LEGIBLY. NO LONG EXPLANATION NEEDED. ANSWER IN 3 DECIMAL PLACES. BOX THE FINAL ANSWERS.) Let a = 11.66 mm
Question 3 The figure below shows a stepped shaft produced from a turning process on a Lathe Machine. Discuss the step-by-step process of producing the stepped bar and the tools used. During the discussion, mention the components that you are using to archive a certain dimension. The initial bar provided is L = 250 mm and D = 50mm. Required dimensions are lengths: Labels Lengths in mm Diameters in mm A 54 66 46 D 34 46 116 K 186 230 .は.05 -Kは.05- -は.05- -It .05- A B B Note: Procedure required (Narrative): Set-up a . .chuck on the ., insert the bar in the. .and tighten using a . Take out a ., insert it in the ..and lock in position. Select a a ............. with . machine. Select the speed using the . place it in the . .and set the height adjustment with the . Remove the. .., insert it in the . .and lock in position. Ensure.. „and replace it with are taken every time you work on the .on the.
The left side of this equation tells how much energy Q the cylinder gives to the water while it cools. The right side of this equation tells how much energy Q the water and aluminum cup absorb from the cylinder to warm up. Because it is the same energy, they are equal. What is known in this equation? Mcyl 411.7 g, malum 46.5 g, malum+water = 175 g Can you find: mwater =? g Twater = Talum = 20°C (water and cup of room temperature) 90°C, T; = 35°C (hot cylinder and cool "cylinder+cup+water" temperatures) Tcyl kCal Calum = 0.22, Cwater 1 (specific heat of water and aluminum, measured in units kg-°C What are we looking for is Ccul - How we find it? Plug all the numbers into the equation (1), Ccul will be one unknown which you can calculate from the equation. Important, convert all the masses from grams to kilograms! After you find Ccyl, compare it to known value for the copper 0.093(our cylinder is made out of copper). |Ceyl -0.093| % : · 100% 0.093
Why Fsin40= 80*9.8 how can I know is Fsin40
P=17000000