It is desired to have a laminar flow for the piping system shown below. The fluid flowing in the piping system is air at 70 °C. (Note: You must use the physical data from Perry's Handbook) a) Calculate the maximum allowable bulk velocity in m/s for pipes 1, 2, and 3 that will satisfy the statement above. The velocities obtained must satisfy the continuity equation. b) Calculate the Reynolds number of each pipe using the velocity values obtained earlier. c) Calculate the mass flow rate of the system (in kg/min). 142-in. pipe 2-in. pipe 3-in. pipe 1/2-in. pipe

It is desired to have a laminar flow for the piping system shown below. The fluid flowing in the piping system is air at 70 °C. (Note: You must use the physical data from Perry's Handbook) a) Calculate the maximum allowable bulk velocity in m/s for pipes 1, 2, and 3 that will satisfy the statement above. The velocities obtained must satisfy the continuity equation. b) Calculate the Reynolds number of each pipe using the velocity values obtained earlier. c) Calculate the mass flow rate of the system (in kg/min). 142-in. pipe 2-in. pipe 3-in. pipe 1/2-in. pipe

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Use g=32.2 */sec2 (9.81 m/s2) and 60°F (16°C) water unless told to do otherwise.• Google schedule-40 pipe’s thickness at different nominal size to obtain the innerdiameter of the pipe for accurate determinaLon of flow velocity.• Must show your work to support your selecLon. Otherwise, no points will be given.• No peer discussion is allowed.. A cylindrical tank 5 ft high has a constant diameter of 4 ft is full of water. The tank has a hole2. A cylindrical tank 5 * high has a constant diameter of 4' is full of water. The tank has a holein its bo]om that measures 0.1ft^2. All losses are insignificant. How long will it take for the tankto empty? Note that you can NOT assume a staLc head and constant flow rate because thewater head in the tank decreases as the water flows out of the tank (A) 35 sec(B) 70 sec(C) 105 sec(D) 140 sec
B1. A water with viscosity 11.4x10-3 poise is flowing through a pipe of diameter 300 mm at the rate of 500 litres per sec. Find the Reynold's Number & the head lost due to friction in the pipe of length 1 km. (Enter only the values by referring the unit given. Also upload the hand written answers in the link provided) The velocity of flow of water (in m/s) is The value of Reynold's Number is The frictional loss in the pipe (in m) is
3. Calculate the Reynolds number, Re for water flow in a circular pipe. The diameter of the pipe is 50 mm, the density of water is 998 kg/m', the volumetric oil flowrate is 720 L'min, and the dynamic viscosity of water is 1.2 centipoise
Pure milk at 293 K has a density of 1030 kg / m3 and a viscosity of 2.12 cp flowing at a rate of 2,205 kg / s in a pipe having a diameter of 90 mm. a. Calculate the Reynolds number. = Answer. b. Is the flow turbulent No, yes.c. The flow rate required for Reynold's number 2100 is = Answerm / s.
B1. A water with viscosity 11.4x103 poise is flowing through a pipe of diameter 300 mm at the rate of 375 litres per sec. Find the Reynold's Number & the head lost due to friction in the pipe of length 1.5 km. The velocity of flow of water (in m/s) is The value of Reynold's Number is The frictional loss in the pipe (in m) is
A simple rainwater collector used for home garden use is show below. It is comprised of an open-air water tank, a "compliant" or flexible tube, and a valve. To avoid overflow, the valve is set to open when the water in the tank reaches a height of 2m. The valve rests on the ground 3m beneath the tank's base. The outlet of the valve is open to atmosphere. c) Assuming inviscid flow, estimate the average velocity of the water flowing through the tube at the moment when the valve automatically opens. Assume that the tank is very large compared to the tube, so that the velocity of the water at the top of the tank is zero. Assume that the valve provides no resistance to flow when opened. d) Using your answer to part c), calculate the rate of discharge in kg/s when the valve automatically opens. e) Using your answer to part c), estimate Reynold's number. Is the flow laminar or turbulent? Pam = 101 kPa g = 9.81 m/s2 H= 2m p = 998kg/m3 H = 1×10-s Pa s Water Tank |Tube (Smooth) h = 3m d = 5cm…
B1. A crude oil of specific gravity 0.75 is flowing through a pipe of diameter 350 mm and the frictional head loss of 4 m of crude oil between the two ends of a pipe which are 625 m apart. Calculate the Reynold's Number, discharge of crude oil in the pipe. Take co - efficient of friction as 0.0075 and kinematic viscosity as 10 stokes The velocity of flow of oil in the pipe is (m/s) The Reynold's Number for the flow is Discharge of crude oil through pipe (in m3/s) is
Quiz - TMPC332 FLUID MACHINERIES Solve the problem as stated below. Make your solution clear and clear. Mind your own “Solution". Do not copy the solution of others. Problem: A 65 mm. fire hose dischargos water through a no2z/e having a jet diameter of 25 mm. The head lost in the nozzle is 4% of the velocity head in the jet. 4 the gage prescure at the bare of the nDzzle N 540 KPa , (6) the flow or dnNcharge in cms, 6) the velocity at 2 in m/ec, vetvelocity) m/sec 45mm. Ø nozzle stream af H20 Figure: datum -25mm. dia, of jet GNEN; d, = C5mm 0.065m. da 25 mm 0.025m. %3D 2, =0 29a A 0.04 VE 29 (c) Also determine the power develop by the jet in kW.
Please compute the Reynolds number of an oil (0.8 specific gravity, 0.8 cp viscosity) flowing in a pipe of 1- inch diameter at a velocity of 6 ft/s. Is this flow laminar or turbulent?
A piping system is to be installed at place where the pump will transfer the fluid from tank A to tank B. There are two suggested piping designs available to carry the fluid efficiently. Compute and determine which of the available piping arrangement will experience the less pumping powerwith given flow conditions. Discuss the results. Flow conditions are same for both type of designs and given as: Pipe material: stainless steel Volume flow rate: 40 L/sec Assume the working fluid is water at standard atmosphere temperature and both tanks areopen to atmosphere. Pipe inlet is sharp-edged and bends are sharped without vanes. Elevations are as ?? = ?? ? and ?? = ?? ?
water flows through 30 mm internal diameter pipe at atmospheric pressure. pitot tube measures the velocity of water at the center of pipe as shown in the fig. the pressure difference between the impact tube and the static tube is 20cm of carbon tetrachloride (density: 1600 kg/m³). calculate the volumetric flow rate through the pipe in cubic meter per hour. velocity of water is cp.
Mechanical-Energy Balance and Friction Losses. Hot water is being discharged from a storage tank at the rate of o.223 ft3/s. The process flow diagram and conditions are the same as given in Example 2.10-6, except for different nominal pipe sizes of schedule 40 steel pipe as follows. The 20-ft-long outlet pipe from the storage tank is 1-in. pipe instead of 4-in. pipe. The other piping, which was 2-in. pipe, is now 2.5-in. pipe. Note that now a sudden expansion occurs after the elbow in the 13-in. pipe to a 2}-in pipe.