lu estion y In the opened tor_a long time f then it- is su'ddenly losed at ’t :0.- -obtain the mpre ssion t20. Alzo Calculate thevoitage_oios s. inductor obtor 10 ms Circuit shown, switth is for Current throughinducetor ' for Use classical methed- 30 l www 20-v Ans: -40 t. 2. 10 40L %3D V (10 ms) : -1:34 V.

lu estion y In the opened tor_a long time f then it- is su'ddenly losed at ’t :0.- -obtain the mpre ssion t20. Alzo Calculate thevoitage_oios s. inductor obtor 10 ms Circuit shown, switth is for Current throughinducetor ' for Use classical methed- 30 l www 20-v Ans: -40 t. 2. 10 40L %3D V (10 ms) : -1:34 V.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Propose Snubber circuits that will take care of dv/dt, di/dt protection and provide Trapped energy recovery and save against the inductive kick from the load?
Question 2) How to calculate icorr, ecorr, rp and corrosion rate manually. Use mild steel/aluminium in 0.5 M HCI Sweep potential from -50 mV to + 50 mV of the open circuit (OC) or freely exposed potential. Use 0.5 mV steps each second (0.5 mV s-1) Plot data E - i Determine the polarization resistance (Rp) Determine the Ecorr and the corrosion rate.
Design a DC power supply using FWR to perform the following requirements. Find V_dc, V_rms, V-ripple, PIV of the diode. draw the waveform of (V_in, V_out, L_in, I_load, V_diode and I_diode). Input voltage = 25 Transformer turn ratio 0.1 load resistance = 1k ohm Ripple factor = 0.025 Diode type =Si
C'uk Converter Design A C'uk converter has an input of 12 V and is to have an output of - 24 V supplying a 60 W load. Select the duty ratio, the switching frequency, the inductor sizes such that the change in inductor currents is no more than 12 percent of the average inductor current, the output ripple voltage is no more than 1.5 percent, and the ripple voltage across C1 is no more than 3 percent.
we Q2/ what Ms meant by Pulsse Moduletim? why need PM ?
For the circuit shown in figure. For the circuit shown in Figure IF IB= 40 MA , VBB= 6v, RE= | Ksr, P= 80o FRc Re VeB Re The value of IE is . . mA..* О 3.24 O 4.24 O 5.24 O 6.24 O 1.24 O 2.024 The value of RB is . Kohm.. * O 52.5 O 55.5 O 47.5 O 57.5 O 25.5 O 48.5 The value of Vce is .. volt. NOTE: USE Rc= 3 Kohm, and Vcc= 15 volt. * O 5.04 O 2.04 1.04 O 4.06 O 4.04 O 3.04 O O O O O ООО О о
In the circuit given in the figure | VBE | = 0.7V, R1 = 17.07Kohm, R2 = 64.82Kohm, RC = 1.49Kohm, RE = 4.46Kohm, VCC = -11.00V, Beta = 125.00, calculate the IC current by full analysis. When making your transactions, 2 steps will be taken after the point. Select the closest option according to +/- 10% margin of error. There is only one correct answer to the question. vcc RE C1 R2 Q1 c2 RC R1
Sketch the DC load line for the fixed bias circuit and place the Q-point on it. - (1.24 MA, Io.76V) %3D Q - Peint Vcc =+12V RC 1k2 RB 1 MQ BC107 Vc VB Quantity Measured VB 0-6 28 volt 07-82 V1t 0.628 volt VC V BEQ IBQ 0-0000|13,A A 0-00418 A 0.782 Uolt IcQ V CEQ Bac
i just want a paragraph of these sensors and their function and which is best then the other.PZT-5HPZT-5JModif. PZT-5A
Write the loop equations for a Buck converter in the two modes if the inductance is characterized by a combination of inductance L1 in series with an equivalent resistance r1, filter capacitance is characterized by a capacitor C1 in series with resistance r2. Also assume that the controlled switch has a drop of 0.4V and the freewheeling diode has a voltage drop of 0.65v. Draw the corresponding equivalent circuits in each mode.
Ge 10:1 m Thanks Any help will be appreciated. S BL • I am doing a AC DC 12 W Regulated power supply with 110 vrms and 60HZ as an input, and I need an output of 6v and 9 V. I have the designed already: the step-down transformer, Resistor as a current limiter to protect the Zener diode, a capacitor for the ripple voltage, and a 2 state switch ( when the switch is closed to the RL will give 9 V and when is closed to the S will give 6V as an output). • I need some support with some calculations to find PIV for each diode // Average Power// some calculations in how to find the values for the resistors and capacitors to accomplish the desire output // and some calculations for the ripple voltage. Note: the Zener is regulated to 9v. I know the RL>R to get the desire output.
wit Determine Ssketch the output voltage mave form? 1MF- pvi/v 200KR Viown 80807 -4