m³ 3 S Water flows at a rate of 0.035 in a horizontal pipe whose diameter is reduced from 15cm to 8cm by a reducer. If the pressure at the center is measured to be 480kPa and 445kPa before and after the reducer, respectively. Determine the head loss. Also consider a correction factor for kinetic energy to be 1.05.

m³ 3 S Water flows at a rate of 0.035 in a horizontal pipe whose diameter is reduced from 15cm to 8cm by a reducer. If the pressure at the center is measured to be 480kPa and 445kPa before and after the reducer, respectively. Determine the head loss. Also consider a correction factor for kinetic energy to be 1.05.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 3. A 30 cm pipe is connected by a reducer to a 10 cm pipe. Points 1 and 2 are at the same elevation. The pressure at 1 is 170 KPa. The flow is 28.50 liters/sec and the energy lost between 1 and 2 is equivalent to 18 KPa. Compute the pressure at point 2 if the liquid flowing is oil (s = 0.80) . ANSWERS MUST BE IN 3 DECIMAL PLACES.
A closed tank partially filled with water up to a height of 1 m, having an orifice of diameter 20 mm at the bottom of the tank. Determine the pressure for a discharge of 3.0L/s through the orifice.Take Cd= 0.62. Include FBD if needed. a.128.8 kPa b.130.5 kPa c. 108.8 kPa d.118.8 kPa
QI/ Water flows from the reservoir on the left to the reservoir on the right at a rate of 0.45 ms. The formula for - Ekevation? the head losses in the pipes is h - 0.02 L: D 2g What elevation in the left reservoir is required to produce this flow? Also carefully sketch the HGL and the EGL for the system. Note: Assume the head-loss formula can be used for the smaller pipe as wel as for the Elevation 34 m 80 m 90 m D, =0.344 m A, -0.1 m D,= 0.486 m A- 02 m larger pipe. Q2/ A horizontal pipe carries cooling water at 10°C for a thermal power plant. what is the pressure in the pipe at L= 2000 m? The head loss in the pipe is 0.02(L/D)V + Eerhm- 0n -D02m 28 Detn where Lis the length of the pipe from the reservoir to the point in question, V is the mean velocity in the pipe, and Elvation =m L-2000m (2. Dis the diameter of the pipe. The pipe diameter is 20 cm and the rate of flow is 0.06 mls, Q3/ For the parallel-pipe system of L-250 D-3 in Fig. each pipe is cast iron, and the pressure drop p -…
SN=23 SUPPLEMENTARY QUESTION The figure shows two reservoirs connected by a pipe. The discharge rate in the pipe is known to be equal to SN/100 (m/s) (where SN is the sum of your student number). Calculate the height of the second reservoir (H2), and the pressure head, velocity head and elevation head at point 3 (mid-point of the pipe). Hi-300 m Ha datum A SN/1000 L- 100 x SN (m) D 0.3 m
What is the required pump power (Pa) for the system below? The source reservoir is on the right side of the figure The outflow is released as a water jet to the atmosphere (on the left) Discharge rate is 0.11 m3/s Pipe total length is 180 m Pipe diameter is 0.2 m Friction factor (f) is 0.01 Minor losses are negligibleCHOOSE ONE: 25 KiloWatt 169 KiloWatt 269 KiloWatt 112 KiloWatt
Theflowrateofwaterthroughacastironpipeis5000GPM.The diameter of the pipe is 330mm, and the coefficient of friction is f=0.0173. What is the pressure drop over a 30m length of pipe
Water flows through a 300mm diameter pipe at a velocity Of 3.00 m/s. Determine the weight flow rate in N/s. Do not write the unit. You will only jnput the numerical answer in the space provided. Unit of the Correct Answer: N/s O 9810.000 O 2,080.284 O 8829.000 1202.284
A PIPELINE WITH A PUMP LEADS TO A NOZZLE AS SHOWN. FIND THE FLON RATE WHEN PUMP DEVELOPS AN 80FEET HEAD. ASSUME HEAD LOST IN THE 8-INCH PIPE TO BE THERE TIMES ITS VELOCITY HEAD WHILE THE HEAD LOST IN THE 4-INCH PIPE TO BE TEN TIMES VELOCITY HEAD. FIND: a)COMPUTE THE FLOW RATE b) FIND THE PRESSURE HEAD AT THE SUCTION SIDE. PLEASE ANSWER IMMEDIATELY WITH COMPLETE SOLUTION THANK YOU!
Gasoline having a specific gravity of 0.8 is flowing in the pipe shown at a rate of 5 cfs. What is the pressure at section 2 when the pressure at section 1 is 18 psig and the head loss is 9 ft between the two sections? Assume a = 1.0 at all locations. A₁ = 0.80 ft² O 30.6 psia O 2592.0 psia O 2286.6 psia 15.9 psia Vertical 12 ft A₂ = 0.20 ft²
In a horizontal 5-inch pipe (ID = 5 in.), water is being delivered at a stable discharge of 25 ft³/s. if the pressure increased from 20 psi to 40 psi after a centrifugal pump, how will the flow velocity be affected? O The flow velocity will increase by 4 times. O The flow velocity will decrease by half. O The flow velocity will remain the same. O The flow velocity will double.
Situation 1: In the pipe system shown, the velocity of water in pipe A is 1 m/s. The friction factor f = 0.02 for all pipes. a. Determine the discharge in pipe B. b. Determine the velocity in pipe C. c. Determine the headloss in pipe E. d. Determine the difference in elevation of the two reservoirs. Water D A 300 m 200 mm D 300m 500 mm Diom 600m 300mm Diam 300m 300mm D B 800 m 300mm Diam E
A municipality wants to determine the flow rate into the plant based on pipe size, elevation difference, and assumed roughness, for the water supply reservoir is shown in the figure below. The pipe is an old 4-inch diameter Cast Iron with a Hazen Roughness coefficient of 100 & 223 feet long. The difference in elevation is 62 feet. The pipe has a strainer at the entrance (k-1.9), a valve (k=8.6), a check valve (k = 2:7) and 3- 90° bends (k-0.83). The flow exits into a receiving pond at the WTP. Provide the flow rate in Gallons Minute. per WTP Az