• Compute the maximum shear stress and angle of twist of each type of shaft below. – Closed tube shaft – Open tube shaft• Briefly describe which type of shaft is more effective.• See the dimensions of each tube, the value of internal torque, and the shear modulus in the next page. WeldNarrowslit1 = 0.156OT+d = 3.188→Ed = 3.188--D = 3.500–-ED = 3.500(a) Closed tube(b) Open tubeFIGURE 3-12 Comparison of closed andоpentubesunits, inches.to the shaftsapply the same torgueof each type (closed vs vpen),Q) when weT = 10* binレン Lo inT matG : 10 psimax7VSclosedopen

Given: To find: Maximum shear stress and angle of twist of both shafts

Narrow slit 3D 0.156- Weld +d = 3.188 D = 3.500- Ed = 3.188– ED = 3.500 %3D %3D (a) Closed tube (b) Open tube FIGURE 3-12 Comparison of closed and open tubes vnits? inches. Q) when we apply the same torque to the shafts of each type Cclosed vs opon), T= 10* bin Lo in G= 10" psi ニ T max' T mat VS cloced Open

Narrow slit 3D 0.156- Weld +d = 3.188 D = 3.500- Ed = 3.188– ED = 3.500 %3D %3D (a) Closed tube (b) Open tube FIGURE 3-12 Comparison of closed and open tubes vnits? inches. Q) when we apply the same torque to the shafts of each type Cclosed vs opon), T= 10* bin Lo in G= 10" psi ニ T max' T mat VS cloced Open

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A W N L N W nút happens tu tne y-valucJ - Problems 5-8, write the equation of the line shown. 6. 6- 4- 4- 3 2- -2-12 1 2 -2-11A1 2 -2- -4 8. 1 1 ed hapou -4-3-2-11- 2 3 4 123 32-11 -2- 4-
The Steel Wheel on The Steel Rail. Flange- Wheel Axle Tie Rail
= 1 ective diameter of 75 i clutch have an effe S i, e 10.34, The contact surfaces in a cone requing s - S ind the torque The semi-angle of the cone is 15°, The coefficient of. s Pee : produce slipping of the clutch if an axial force applied is 180 N. . . orn, This cluch is employed o connect an electric motor running “mf”r:f o /‘.’K'W:‘ tha Jopwleel which s iniially stationary: The lywheel ha a mass of o e sricres o 150 mm. Calculate the time required for the flywheel to attain full speed and als 8 lostin the slipping of the clutch,
Write the solution for the following: Member BC = -447.21 Member DF = -800 Member CE = 100
1- A bush roller chain drive is used to transmit 4 kW of power from the driving shaft on a hydraulic motor runs at 1200 r.p.m to the driven shaft which runs at 350 r.p.m. The drive is required to operate continuously with drop lubrication and driven machine is such that load can be regarded as fairly constant. Design the chain drive by calculating leading dimensions, number of teeth on the sprockets taking into account that the available distance between the two shafts centers is 400mm + 4% no more no less.
Solve for Problem 2, when RN1 = 0145
0-25 mm kead He nearurement of the moromeler (c) E25 10 15 20 20 0-25 mm TTTTTT|
Show the complete solution of the given problem. The answers are answers are: Cc = 24.787 Wn = 51.64 Wd = 44.72 Keq = 640 Ieq = 0.24 df = 1/2 Xo = 5mm Vo = 0
The motor drives a pump with a power of P = 34 kW. A steel tubular shaft with an outer diameter D = 55 is designed between the motor and the pump mm. The maximum allowable shear stress of the shaft material is τsall = 70.5 MPa. How large must the wall thickness of the pipe be at least in order for it to withstand the required power. The engine speed is n = 1000 rpm. Use units [N, mm] Enter the answer to one decimal place. Do not round the invoices in the intermediate stages, but only the final answer!
QUESTION 1 TOLERANCE A solid steel shaft with a diameter of 130 mm must be press-fittd in a journal bearing (Figure 1) with an inlet and outet diameters of 130 and 145 mm, respectively. Both solid shaft and journal bearing require rigidity and alignment with an accuracy of the location. Consider a journal bearing hlet diameter as the basic size. Outlet Bearing Inlet Joumal Figure 1 AJournal Bearing 1.1 State the two applicable standards when determining the fits for holes and shafts. Determine the following: 1.2 the tolerance class, ISO code, and the nominal diameter that can be used, 1.3 the tolerance limits for both the solid steel shaft diameter and the journal bearing inlet diameter, and 1.4 the dimensions of both the solid steel shaft diameter and the journal bearing inlet diameter.
the shaft and Bols bolts. [Ans. 300 mm; 56 mm] 11. Design a bushed-pin type flexible coupling for connecting a motor shaft to a pump shaft for the following service conditions: Power to be transmitted = 40 kW; speed of the motor shaft= 1000 r.p.m. ; diameter of the motor shaft = 50 mm ; diameter of the pump shaft = 45 mm. The bearing pressure in the rubber bush and allowable stress in the pins are to be limited to 0.45 N/mm2 and 25 MPa respectively. [Ans. d, = 20 mm; n 6; d, = 40 mm; 1 152 mm] :1.1
Trial Number 1 h 2 Aluminum roller with brass center used 3 Note: h, and theta are shown in the table below. S = 1200mm, R = 81mm, r = 20mm, w1 = w3 = 10mm, w2 = 31mm Height, h (m) 0.007 Rail 0.02 0 0.16 h sin == Angle of Elevation, 0 (°) 0.033 0.95 7.66 14.37 R 10.35 Roller 1st Run (s) 2nd Run (s) 3rd Run (s) 9.05 15.36 10.13 |w₁|w2|w3| 8.90 15.13 10.35 8.97 Average Time (s) 14.95 10.28 8.973 6. Calculate the mass and mass moment of inertia of the roller using basic principles (theoretically). The specific gravities of brass and aluminium are 8.47 and 2.7, respectively. 7. Calculate the linear and angular velocities and accelerations of the roller using the results from the first experiment. Assume that no slip occurs. 8. By applying the conservation of energy to the results from the first experiment and the velocities calculated in Step 7, calculate the mass moment of inertia of the roller.