Note for Question 2 is 3=7 Question 2 Consider the circuit shown in Figure Q2. A B Determine the a-parameters of the circuit shown in Figure Q2. You need to derive the a-parameters directly, without converting it from any other types of parameters. C D (11) Convert the a-parameters from (1) to b-parameters + 1 V₁ I₁ 502 13 252 214 Figure Q2 [a b] c d 14 WWW (1/β) Ω 12 + V2

Note for Question 2 is 3=7 Question 2 Consider the circuit shown in Figure Q2. A B Determine the a-parameters of the circuit shown in Figure Q2. You need to derive the a-parameters directly, without converting it from any other types of parameters. C D (11) Convert the a-parameters from (1) to b-parameters + 1 V₁ I₁ 502 13 252 214 Figure Q2 [a b] c d 14 WWW (1/β) Ω 12 + V2

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Determine teh output of teh DAC in Figure (a) if teh waveforms representing a sequence of 4-bit numbers in Figure (b) are applied to teh inputs. Input DO is teh least significant bit (LSB). 200 kN Doo W R 0 12 3 4 5 6 7 8 9 1011 12131415 100 kN +5 V Do +5 V DI +5 V D2 +5 V iiii D3 D 10 kN 50 kfl D2 0 W- 25 kN D3 0- (a) (b)
Q2) determine A>B, A
Solve all please Q1) Choose the correct answer: I. The circuits can be divided into two broad categories analog and digital are called: a- control circuits b- logic circuits c- electronic circuits d- design circuits II. Magnitude comparison is performed by a logic circuit called a: III. a- divider b- multiplexer c- decoder d- comparator The resolution of 5 bits ADC from analog signal (-4-4)V is: a-0.2 b-0.22 c- 0.24 d-0.25 IV. The full scale output from analog signal (-4-4)V by using 5 bits ADC is: a- 3.7 b- 3.75 c-3.85 d-4
Calculate the output for the given circuit . R2 R2 Voa R1 Let the values are R1=775.8ohm,R2=506.8 ohm .The error voltage is =8.3 Volt and the initial value of output is 3.7 Volt. Vout = volt.
Q19. For the circuit diagram shown in FigureB19. Vin and Vout corresponds to input and output voltage, V3 corresponds to output voltage from second stage of the circuit and A1, A2, A3 corresponds to Gain of each block. V3 =? Vin=3.5V Vout = 11.5dB Al- 6 A2-? A3-0.88 Figure B19 i) Compute the output voltage V3 and A2. ii) Whether the circuit in figure B19 will provide amplification or attenuation? Justify your answer.
Q1) Choose the correct answer: Solve all please I. The circuits can be divided into two broad categories analog and digital are called: a-control circuits b- logic circuits c- electronic circuits d- design circuits II. Magnitude comparison is performed by a logic circuit called a: a- divider b- multiplexer c- decoder d- comparator The resolution of 5 bits ADC from analog signal (-4-4)V is: a- 0.2 b-0.22 c- 0.24 III. IV. V. d- 0.25 The full scale output from analog signal (-4-4)V by using 5 bits ADC is: a- 3.7 b-3.75 c-3.85 d-4 The number of quantization level of 10 bit ADC from analog signal (-5~5)V is: a- 128 b- 256 c- 32 d-1024
(b) Figure Q5 (b) shows a state transition diagram consisting of four states with the signals S, W, X, Y and Z using Finite State Machine (FSM) concept. X'I Z so XY'I Z X+Y/ W Y/ W X/ W S3 S1 X'Y'/ W Y'IZ Y'IZ S2 XYI Z Figure Q5 (b) Based on the Figure Q5 (b), answer the following questions: (1) What is the types of FSM model shown in Figure Q5 (b) ? (ii) Determine the input signals. (iii) Determine the output signals?
FINAL ANSWER IN 2 DECIMAL PLACES. ASAP. For the given figure, determine the h parametersH-| A C | | B D |
A 4bit D/A converter use an inverting summer as its output stage. The input voltages can be either 0 or 5 V in a binary sequence. The input resistors are as follows: R1 = 1 k, R2 = 2 k, R3 = 4 k, R4 = 8 k, and RF = 1 k. Determine the output voltage for the case where the V1 = 5 V, V2 = 5 V, V3 = 0 V, and V4 = 5 V.
Scimal value of the value that will occur at the ADC output. (ADC is 12 Question 2 MN is the last two g160100555 - yu digits of In an analog measurement operation set as an external reference, the reference source of the ADC is a voltage source of 5 analog input, write the g160100555-Gu Aumber your student 010055 g160100555 - Yu 9441 20100 g160100555- Y 44 s0100538 g160100555 - Y 944 201005 g160100 2447 .5Volts. In case of 3.5V voltage to the 30100555 -98 9447 30100555 - 987 30100555
You are working as a hardware engineer in an R&D department and your new task is to design a voltage divider bias circuit. Vcc You are told that you have to use a 2N2222A transistor manufactured by Central Semiconductor Corp. and a power supply of Vcc = 22 V. RC R1 a. Find the datasheet of the selected transistor in Internet and upload it together with your homework. b. From the datasheet identify the range of B suitable for the Ica required in this problem and use the minimum value in your design. R2 RE c. Calculate the values of four resistors so that VCEQ = 12V and Ica = 1.4 ma. Make sure that you select standard resistor values. d. Plot the load line and indicate the operating point on it. Is the location of operating point is a good one for an amplifier with a reasonable performance ? Explain your answer.
1.With a neat diagram ,explain about the working of 4 bit R-2R ladder Type DAC.