NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. The 6-m long pole ABC is acted upon by a 495-N force as shown in the figure. The pole is held by a ball-and-socket joint at A and by two cables BD and BE. m 28 1.5 m P E C B A N. N. N)i + ( 3 m 3 m 3 m 3 m For a = 1.5 m, determine the tension in each cable and the reaction at A. The tension in cable BD is The tension in cable BE is The reaction at A is -([ 1.5 m Nj+( N)k.

NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. The 6-m long pole ABC is acted upon by a 495-N force as shown in the figure. The pole is held by a ball-and-socket joint at A and by two cables BD and BE. m 28 1.5 m P E C B A N. N. N)i + ( 3 m 3 m 3 m 3 m For a = 1.5 m, determine the tension in each cable and the reaction at A. The tension in cable BD is The tension in cable BE is The reaction at A is -([ 1.5 m Nj+( N)k.

Name: NOTE: This is a multi-part question. Once an answer is submitted, you
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part.The 6-m long pole ABC is acted upon by a 495-N force as shown in the figure. The pole is held by a ball-and-socket jointat A and by two cable

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.8.22P: A cargo ship is tied down to marine boll arts at a number of points along its length while its cargo...

See similar textbooks

Similar questions

Calculate the total moment of the system about point A, when P1 = 8 kN, P2 = 10 kN and 0 = 45°. %3D %3D 25 kN.m 1.5 m A –1.5 m- P2 →1.5 m- Select one: a. 23.21 kN.m (CCW) b. 48.21 kN.m (CW) c. 23.21 kN.m (CW) d. 48.21 kN.m (CCW)
The force in the rope if F= 500 N. The dimensions of the beam are: AC = 2 m, AD= 3 m, DB= 2.5 m, h= 1 m and r= 0.3 m. F Ac PENDIDIK C AD DB Which side is the easiest to use to solve for the internal forces at C. O Left side, less forces. O Right side, less forces. Either sides have the same number of forces. B
The weight of the linkage AB =BC= 20KG .Find the force acts on bar BC -875 mm- B 400 625 mm 30 60 F = 800 N
5) Find the forces developed at pins E. E -1.5 m 4 kN/m D -1.5 m- B 2 m C 5 kN
4. Forces F =F-20N and the third force F3 25N act on a cube with the side of a=2m. a. Find the screw driver (wrench) that is created by these forces i.e pitch, Mparallel, Mpapendicular b. Find the point of intersection of the axis of the wrench with the x-y plane. How do you check your answer is correct? G F D A B.
Q.3) An airplane wing is supported by a truss structure as shown below. Three vertical forces are applied at points C, D, and E along the upper surface of the wing. Use the Method of Sections to find the force in members BC, CG, and GF. Indicate whether the member is in tension or compression. A I 8' 2500 lb 3000 lb 1500 lb H 8' 8' 8' B C -G- D E F 18'
Q5/A) From the figure below, determine the reaction force at pin C. A 000 0.6 m 10 kN 0.6 m 0.8 m 60° 0.4 m 6 kN OB
(٢٦+ * Find the two forces Fbc & Fac as :shown in the figure below Fab=30 N 110 30/Fbc (Fbc=45.18 N and Fac= 58.8 N) O (Fbc=38.56 N and Fac= 56.38N) O (Fbc=75.18 N and Fac= 78.8 N) O ! Fac
1. A tripod shawn supports of note that ball and rocket joints are used to mount the tripuod a load P=1000N at point A. Take at points B,D, and C. consider the t LI L 2 L2: 4 L3 : 3 A : 45° g :30° %3D on x-z plane L2 POINT C (2,-2,3) C0,0,0) ミー- Determine the ff Force of AB - N Force of AC - N Force of AD : N
A horizontal rod of length L= 9.64 m is attached to an axel in such a way that the axel is located at its left end. Three forces are acting on the rod: F1= 11.6N at the location 2.59 m from the axel, F2 = 15.7 N at the location 5.02 m from the axel, and F3 =15.0 N at the laction 2.31 m from the axel. F1 (pointing up and to the right) makes an angel of 47.7 degrees with the rod, F2 (pointing up and to the left) makes an angel of 45.1 with the rod, and F3 points directly downwards. Calculate the net torque that these three forces exert on the rod. Also, indicate if the torque is clockwise it counter-clockwise.
What would be the resultant force F of the triangular distributed load and its location d measured from point A. 150 lb/ft -3 ft < 5 ft 2 ft Select.one: a F-375 Ib and d = 1.67 ft b.F=300 lb and d = 2.5 ft OcF=37S Ib and d = 3.67 ft id F=750 lb and d = 3.67 ft
Question 2 Find the value of The reaction force at the support A. (X,XX,XXX represents the last digits number pf your IC) 4m 400 KN 10 m B 60 KN 4m 10 m. 157KN 4m 17 m D