Please find correct answer A bolted joint is shown below. The maximum shearstress, in MPa, in the bolts at A and B, respectiveyare3 holes of M10 x 1.75 mm bolts206 mm thickC40B40-AF 10 kN20%3D150(all dimensions in the figure in mm)

Answered: nt is shown E

Engineering

Mechanical Engineering

nt is shown E

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.8.12P: A punch for making a slotted hole in ID cards is shown in the figure part a. Assume that the hole...

See similar textbooks

Similar questions

Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
A steel punch consists of two shafts: upper shaft and lower shaft. Assume that the upper shaft has a diameter d1= 24 mm and the bottom shaft has a diameter d2= 16 mm. The punch is used to insert a hole in a 4 mm plate, as shown in the figure. If a force P - 70 kN is required to create the hole, what is the average shear stress in the plate and the average compressive stress in the upper and lower shaft of the punch?
Two steel wines support a moveable overhead camera weighing W = 28 lb (see figure part a) used For close-up to viewing of field action at sporting, events. At some instant, wire I is at an angle a = 22° to the horizontal and wire 2 is at angle fi = 40°. Wires I and 2 have diameters of 30and 35 mils, respectively. (Wire diameters are often expressed in mils; one mil equals 0.001 in.) (a) Determine the tensile stresses s and s2 in the two wires. (b) If the stresses in wires 1 and 2 must be the same, what is the required diameter of wire 1 ? (c) To stabilize the camera for windy outdoor conditions, a third wire is added (see figure part b). Assume the three wires meet at a common point coordinates (0, 0. 0) above the camera at the instant shown in figure part b. Wire I is attached to a support at coordinates (75 ft, 48 ft, 70 Ft). Wire 2 is supported at (-70 ft. 55 ft, 80 Ft). Wire 3 is supported at (-10 ft. -85 Ft, 75 ft). Assume that all three wires have a diameter of 30 mils. Find the tensile stresses in all three wires
A punch for making a slotted hole in ID cards is shown in the figure part a. Assume that the hole produced by the punch can be described as a rectangle (12 mm X 3 mm) with two half circles (r = 1.5 mm) on the left and the right sides. If P = 10 N and the thickness of the ID card is 1 mm, what is the average shear stress in the card?
S-3) In order to carry the 100 KN force safely on the frame in Figure 3, find the diameters of the B and D pins (B single cut D double cut), the thickness t of the BD bar. (Safety Cat.(S)=2, T = 250 Nmm2 o -350 N/mm2) 40.a mm 300 mm a=9.6 TAKE 60.a mm 50 mm D Yatağı 100 mm t mm F=100 kN
S-3) In order to carry the 100 KN force safely on the frame in Figure 3, find the diameters of the B and D pins (B single cut D double cut), the thickness t of the BD bar. (Safety Cat.(S)=2, T = 250 Nmm2 o -350 N/mm2) 40.a mm 300 mm ТАКE a-9,6 60.a mm 50 mm D Yatağı 100 mm C t mm |F=100 kN
For the joint shown in the figure, if F = 28 kN and dn = 12.8 mm, calculate: 7.5 mm F F 12 mm 12 mm 7.5 mm - de - F 18 mm - F 18 mm 125 mm 1. The largest bearing stress in MPa between the pins and the members; a. 146.23 MPa b. 182.29 MPa c. 174.56 MPa d. 199.37 MPa 2. The average shear stress in MPa in the pin and; a. 108.80 MPa b. 116.14 MPa c. 136.23 MPa d. 98.01 MPa 3. The largest average normal stress in MPa in the members. a. 181.23 MPa b. 175.76 MPa c. 191.26 MPa d. 150.32 MPa
Solve the following problems as stated below. Draw the figure and FBD. PROBLEM A flanged bolt coupling consist of 9 steel bolts evenly spaced around a bolt circle 300 mm. in diameter and 6 bronze bolts on a concentric bplt circle 200 mm. in diameter. What are the sizes of bolts diameters for steel and bronze, if the torque applied is 6,000 N-m and without exceeding the stress of 60 MPa in the steel and 40 MPa for the bronze? The ratio of the bolt diameter dp / ds = 0.50. For steel, use Gs = 83 GPa and for bronze, Gp = 28 Gpa. R Rs Rb
Solve the following problems as stated below. Draw the figure and FBD. PROBLEM A flanged bolt coupling consist of 9 steel bolts evenly spaced around a bolt circle 300 mm. in diameter and 6 bronze bolts on a concentric bplt circle 200 mm. in diameter. What are the sizes of bolts diameters for steel and bronze, if the torque applied is 6,000 N-m and without exceeding the stress of 60 MPa in the steel and 40 MPa for the bronze? The ratio of the bolt diameter d, / ds = 0.50. For steel, use Gs = 83 GPa and for bronze, G, = 28 Gpa. %3D Rs Rp
Agui - 4550/2 =2276 two plates each with thickness t - 16 mm are bolted together with 6-222 mndia. bolts firming alap Joint Bolt spacing are follows St- $40mm S2 - 80mm, S3=150mm effective bolt hole dia. is 25mm A36 is used. Compute the allowable tensile Strength P t = 16 mm &t 52 747₁ 0 O O 40 60 80 40 +=16mm S-400 $3-100 S2-40 7 @ 4umm P
In the clevis shown in Fig. 1-11b, the minimum bolt diameter (d=22mm) and the minimum thickness of each yoke(t=10mm) without exceeding a shearing stress of 83MPa and a bearing stress of 138MPa. -Find the support load (P=?) Y. Figure 1-11b
A 5⁄8-inch-thick tension member is connected to two 1⁄4-inch splice plates, as shown in Figure The loads shown are service loads. A36 steel and 5⁄8-inchdiameter, Group A bolts will be used. If slip is permissible, how many bolts are required? Each bolt centerline shown represents a row of bolts in the direction of the width of the plates.