One mole of an ideal gas is taken through a cyclic process as shown in the PV diagram below,i.e. from A BCA. In step A B, 180 J of heat flow out of the system; in step B C,100 J of heat flow out of the system; and in step C A, an unknown amount of heat Qu flowsinto the system.p (kPa)A300-200-180 J100-В100 JV (cm³)600200400Note that the conversion is 1 cm3 = 1 x 10-6 m³.7hat is the change in the internal energy of the system as it goes from point A topoint B?В.What is the work done on the system going from point B to point C?С.Determine the heat Qu transferred to the gas as it goes from point C to point A.

Answered: Image /qna-images/answer/210d6554-a7eb-4791-abcb-71c80b41c635.jpg

One mole of an ideal gas is taken through a cyclic process as shown in the PV diagram below, i.c. from A→ BCA. In step A B, 180 J of heat flow out of the system; in step B C, 100 J of heat flow out of the system; and in step C A, an unknown amount of heat Qu flows into the system. p (kPa) A 300- 200- 180 J 100- C В 100 J V (cm³) 600 0. 200 400 Note that the conversion is 1 cm3 = 1 x 10-6 m³. Vhat is the change in the internal energy of the system as it goes from point A to point B? В. What is the work done on the system going from point B to point C? С. Determine the heat Qu transferred to the gas as it goes from point C to point A.

One mole of an ideal gas is taken through a cyclic process as shown in the PV diagram below, i.c. from A→ BCA. In step A B, 180 J of heat flow out of the system; in step B C, 100 J of heat flow out of the system; and in step C A, an unknown amount of heat Qu flows into the system. p (kPa) A 300- 200- 180 J 100- C В 100 J V (cm³) 600 0. 200 400 Note that the conversion is 1 cm3 = 1 x 10-6 m³. Vhat is the change in the internal energy of the system as it goes from point A to point B? В. What is the work done on the system going from point B to point C? С. Determine the heat Qu transferred to the gas as it goes from point C to point A.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

V. W. Th To %3D Room temperature T = 293 K V V. Vp The gas volume changes from Vp to Va at constant temperature T. The cartoon on the right shows a piston of gas undergoing this compression while submerged in a container of room temperature water, which acts as a reservoir. The initial state of this process is a piston containing 2 moles of a monatomic gas at Tc = 293 K (room temperature water) and volume V = a 1.0 m. The gas is compressed until V, = 0.2 m. During the compression, the heat bath of room temperature water maintains the temperature of the gas at T 293 K. Calculate the work done in joules by the gas during this process. Do not include units in your answer. Be careful to use the standard sign convention for work done by the gas. Write your numerical answer in normal form as described above in the instructions to this worksheet.
2. Two insulated cylinders A and B with volumes VA = 2.0 m³ and VB = 5.8 m³ contain chlorine gas at different pressures and temperatures. The cylinders are insulated (no heat is lost to or gained from the outside) and connected by a valve. Initially, the valve is) closed and the gas in the two cylinders has the following values: PA = 4.0x105 N/m², TA = 210 K, PB = 2.5x105 N/m², TB = 580 K. The valve is opened to allow the contents in the two cylinders to mix until the pressure equalizes. valve B a. Assuming there is no change in the temperatures of the containers themselves, determine the final temperature of the gas in the two cylinders. The atomic mass of chlorine gas is 35.4527 u. (1 u = 1.67377x1027 kg) b. Determine the final pressure?
One mole of gas undergoes the cycle shown in the p-V diagram below. A Po B 1. D Po/32 Vo 2Vo 8V Volume 16V. (a) Classify each process in this cycle: A-B, B-C, C-D, and D-A. (b) Find y for this gas. (c) What type of gas is this, monatomic, diatomic, or polyatomic? Pressure
An amount of an ideal gas undergoes the process shown in the diagram below. Assume that during the entire cycle, the number of moles of the ideal gas stays constant. Р. A В V (a) What are the signs of Way the gast Q, and AEint for the process CA? positive positive Wby the gas AEint zero (b) What are the signs of Wby the gas Q, and AEint for the process AB? negative negative zero W by the gas AEint (c) What are the signs of Wby the gas: Q, and AEint for the process BC? Wby the gas positive Q negative DE int zero
N = 0 An insulated tank of volume 10+(10+N)/25 m and with a valve was filled with perfect tri- atomic gas at pressure 10 bar, where N is equal to the last two digitals in your student's ID number. Initially the valve was closed. A paddle wheel was mounted inside the tank and was run by 20 kW engine. The paddle wheel was turn on and at the same time the exit valve was opened. The gas temperature was constant though the whole process (due to very slow flow) and equal to 300 K. Calculate the time needed to decrease the pressure in the tank to 5 bar.
H+ l 82% 7:50 PM ENGLISH A piston-cylinder assembly initially contains 2 m3 of water vapor at 1.8 MPa pressure and 500 °C temperature. Heat transfer occurs from the steam to the environment at constant pressure until the moment the condensation begins. By showing the process change in T- v diagram, a) the mass of water vapor, b) Final temperature, c) Calculate the heat transfer during the process. Camera Conversation Transcribe
2) Two glass bulbs, one on the left with a volume of 2 liters and the other on the right with avolume of 6 liters, are connected to one another by a thin tube that is initially closed by astopcock. The bulb on the left has 0.1 moles of ideal gas, and the bulb on the right isevacuated. The system is in thermal equilibrium with the surroundings at 300K. When thestopcock is opened, the gas flows out to fill both bulbs. Calculate A for this process. If wewere to insert a propeller to extract work as the gas flows from left to right, what is themaximum amount of work that we could possibly extract?
p/atm 2.0 1.0 EXERCISE 3 (c) 3 1 thermal (b) Ⓡ One mole of an ideal gas undergoes a cyclic three-step process according to Figure 2: (a) 1->2: reversible and adiabatic expansion starting at T₁, and pressure = 2 atm. pl (b) 2->3: reversible isothermal compression up to p3 = 1 atm and (c) 3->1: heating under constant volume, at final temperature Ti, and pressure p1 = 2 atm. Calculate the entropy changes of the gas for the three steps and for the cycle. The heat capacity under constant volume is given: cx= 12.47 J mol-¹ K-¹. V Enter your results (with units) in the Table below AS₁1+2 AS2+3 AS3+1 AS1+2+3+1
s > MENG304: Thermodynamics I-2021FALL-LECT-01 > General > Quiz 2 A 300 m3 rigid tank is filled with saturated liquid-vapor mixture of water at 300 kPa. If 15% of the mass is liquid. Determine. The quality % (0 to 100) The specific volume in m2/kg, The density in kg/m2 The total mass in the tank in kg The mixture temperature in °C. Finish attempt here to search
A 2.9 kg mass of saturated liquid-vapor mixture of water is contained within a closed system in a vertically arranged piston-cylinder device at a pressure of P1. Initially, 1.0353 kg of the water is in the liquid phase and the rest is in the vapor phase. Heat is now transferred to the water, and the piston, which is resting on a set of stops, starts moving when the pressure inside reaches P2. Heat transfer continues until the total volume increases by 18 percent. Consider Case #2 from Table 1: Table 1: Case # along with the list of pressures P1 and P2 Case # P1 (kPa) P2 (kPa) 1 100 300 150 300 3 200 500 4 250 500 300 500 6. 350 700 7 400 700 8 450 700
4. A vessel with 8.0 g of helium gas follows the two-step process, 123, shown in the figure to the right. a) Qualitatively describe what is being done to the gas vessel in the two processes. b) Find the values of V₁, V3, P2, and T3. P2 2 atm 0 P 657°C 2 37°C- 1 V₁ Isothermal 3 V3 V
1. A rigid contained fitted with a 200 W resistive heater contains 4 Ibm of N2 (nitrogen). Initially, the gas is at T1 = 47°C and P1 = 1.25 bar. The heater is turned on for 30 minutes. During this time, the container is found to transfer roughly 50 kJ to its surroundings via natural convection. The mass and volume of the heater can be neglected. Assuming the N2 can be modelled as an ideal gas, determine: a. T2 (°C) b. P2 (bar) C. Whether the ideal gas model a good approximation of the system. Show your justification.