d=20mmPb=130 mm-P/2P/23200000Fig. (1)1000Pt=25 mm (Answer 5Q1- For the joint shown in Fig. (1), determine the max. safe load (P) which may be applied if theshear stress in the rivets is limited to 60 MPa, the bearing stress in the plate is limited to 155 MPa andthe tensile stress in the plate is limited to 250 MPa.

Solution: Given: Rivet: Diameter = 20 mm Diameter of rivet hole = 22 mm b = 130 mm t = 25 mm number…

Answered: P/2 d=20mm b=130 mm- P/2 P 200 000 Fig.…

Engineering

Civil Engineering

P/2 d=20mm b=130 mm- P/2 P 200 000 Fig. (1) 000 ²₂ t=25 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The table below is the page of a level field book. Calculate the reduced levels of points C, F and H…

A: Determining RL of C F and H

Q: A cantilever beam of length 1m carries a point load of 1900N at the free end. The cross-section of…

A: Given data:- length of cantilever beam, L=1 m Point load, P=1900 N Dimension of cross-section of…

Q: 8) Using an energy method (strain energy, virtual forces, or Castigliano's Theorem-your choice!),…

A: Given :

Q: A clockwise traverse ABCDEA was surveyed Find the length and direction of line AD Line AB BC CD DA…

Q: A cantilever beam, shown in the figure, is subjected to a concentrated force P at the free end as…

Q: 1, A2 and A3 are 145.31, 257.43 and 59.67 .respectively with a distance of 2.5 m 1208.91m³ O 1280.91…

A: Data given:A1=145.31m2A2=257.43m2A3=59.67m2distance (d) =2.5mVolume is to be calculated by Simpson's…

Q: The maximum stress at the top of the beam before cracking.

Q: fl m→ -2.0 m- e total deflection at B. [Hint: Use

A: a) Take , a = 1m from left , x = 2m from left , l = total length = 4m Given : EI = 2000 KNm2…

Q: Two clay specimens A and B, of thickness 2cm and 3cm, have equilibrium voids rations 0.68 and 0.72…

A: Given: For Clay specimens A : initial void ratio, eo = 0.68 final void ratio, e = 0.50 So,…

Q: Beam ABC with an overhang BC is subjectedto a linearly varying distributed load on spanAB with peak…

A: Given data:

Q: THIS IS NOT A GRADED ACTIVITY. THIS IS JUST A REVIEWER FOR MY TRUSS DESIGN. THANK YOU SO MUCH!…

A: Solution: Given: Diameter of rivets = 16 mm Thickness of gusset plate = 20 mm Allowable Bearing…

Q: Example- bearings. : Convert the following whole circle bearings into quadrante (3) 242° 45' (4)…

Q: The latitude for the figure can be given as (0 = 50° 34¹) 0 245m 161.34m O 155.62 O 160.43m O 165m O…

A: 155.62 is the correct answer.

Q: A simple curve having a degree of curve equal to 5° is connected by two tangents having an azimuth…

A: Given : A simple curve having a degree of curve equal to 5° is connected by two tangents having an…

Q: A clay specimen was tested in undrained direct shear, under a normal stress of 50 kPa. The peak…

Q: Example-3: Find the area of zero circle from the following taken using a planimeter having M = 100…

Q: FIG.P3.9 Determine the reactions at the supports for the beam shown 30 kN/m 70 KN ty

A: Note:- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: al From the figure, determine ?R.L of Q from A D E H1 H2

A: Using figure

Q: 9.4 What specific air-pollution-control devices are available for control of particulate emissions…

A: This question is from environmental engineering Here methods for air pollution control prevention is…

Q: A beam with a wide-flange cross section (seefigure) has the following dimensions: b =120 mm,t = 10…

A: Given data:

Q: A simple beam AB is subjected to a distributed load of intensity g(x) = sin -), where a, is the…

Q: Given the following data from a balanced traverse, find the area of the traverse by DMD method. LINE…

A: Given data: Line Adj.Dep Adj.Lat 1-2 3.14 -18.55 2-3 -55.05 9.45 3-4 -3.53 19.51 4-1…

Q: 0.75 m Steel A = 250 mm² E = 200 GPa 1.5 m Figure P-242 Aluminum L = 2m A = 300 mm² E = 70 GPa B D…

Q: A steel bar is 6.0 ft long and has a circular cross section of diameter d₁ = 0.75 in. over one-half…

Q: The members CJ and CF of the loaded truss cross but are not connected to members BI and DG. Compute…

Q: It is anticipated that the filtration rate should increase with time.True or False?

A: Answer :- False It is anticipated that with increase in filtration rate the time will decrease.

Q: Prob 2. ( Following are the notes for a line of stadia levels. The elevation of BM-A is 184.29m. The…

A: Levelling- It is the method of surveying to calculate rise and fall of different station point and…

Q: Discuss threats of water resources and how they can affect on agriculture

A: Delaying climate change mitigation efforts and developing resilience plans for upcoming changes…

Q: Three different materials, designated A, B, and C, are tested in tension using test specimens having…

Q: 2xy²+4=2(3-x²y)y' A. Prove or disprove if the given D.E is exact. B. If it is an exact D.E, find…

A: Given, 2xy²+4=2(3-x²y)y'

Q: A clockwise traverse ABCDEA was surveyed Find the length and direction of line AD Line AB BC CD DA…

Q: Which of these is NOT a required device/information for the horizontal angle measurement? a)…

A: This given question is from surveying Here we are asked to find instrument/ information required for…

Q: PLEASE WRITE COMPLETE SOLUTION AND BOX FINAL ANSWERS. TABULATE VALUES. THANK YOU. Following are the…

A: Given, Stadia interval, K= 100 C= 0.381m Elev BM-A= 184.29m

Q: In a parabolic vertical curve, if the rising grade is 2% followed by a downgrade of 2%, and the rate…

Q: Q1: Discuss seven practical applications of Lagrangian and Eulerian descriptions of fluid flow.

A: Lagrangian descriptions of fluid flow: In here that the fluid particles are marked, so the flow…

Q: A clockwise traverse ABCDEA was surveyed Find the length and direction of line AD Line AB BC CD DA…

A: To Determine Length and bearing of line AD.

Q: water flows from a reservoir (A) showe in throgh a pipe of diameter (di=120mm) and lengh (Lis 20 m /…

Q: Determine the forces in members EH and El of the double Fink truss (positive if in tension, negative…

Q: ou are in charge of a site in Heme Proctor max dry density of the soil compacted to a relative…

A: Given : R = 95% γdmax = 1770 kg/m3 Relative compaction =minimum dry densitymaximum dry densityR%…

Q: If the Whole circle direction is (34°30') and the magnetic declination is (3°30')W the : magnetic…

Q: Determine the dimensions of a high rate trickling filter for the following data: (ii) Recirculation…

Q: ing an incline on the slope w

Q: (b) A hollow rectangular section has outside dimensions 30cm x 15cm. The material of the section is…

A: given- outside dimension b=30 cma=15 cmthickness t=2.5 cminside dimensionb1=(30-2.5)=27.5…

Q: a.) Derive the appropriate equations for shear and bending moment throughout the beam. Measure…

Q: An oblique shock wave at an angle of 35 degrees occurs at leading edge of a symmetrical wedge. Air…

A: Given data:-Angle of oblique shock wave, θ=35° For upstream of the wave; Mach number, M1=2 Pressure,…

Q: SITUATION. Given a trapezoidal beam with width at the top of 300mm and width at the bottom of 500mm…

A: To Determine Cracking moment in kN-m

Q: A steel beam 12m long is fixed at both ends and carries a superimposed uniformly distributed load of…

A: Find maximum bending stress.

Q: For the machine element shown, locate the y coordinate of the center of gravity. 50 mm 50 mm 60 mm…

A: Given data:- The Hollow circle, r2=30mm

Q: If load C has a mass of 380kg, determine the required minimum diameter of the solid L2-st rod AB to…

A: Given :

Q: Question 8 An aerated bench-scale reactor is used to evaluate a non-recycle, secondary biological…

Concept explainers

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.

Question

d=20mm
P
b=130 mm-
P/2
P/2
3
200
000
Fig. (1)
1
000
P
t=25 mm

(Answer 5
Q1- For the joint shown in Fig. (1), determine the max. safe load (P) which may be applied if the
shear stress in the rivets is limited to 60 MPa, the bearing stress in the plate is limited to 155 MPa and
the tensile stress in the plate is limited to 250 MPa.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

(b) Two connected steel bars as shown in Figure Q2(b) are axially loaded with 100 N at node 3. The cross section area for bar B is half of bar A. The horizontal displacement at node 2 is half of displacement at node 3. By using finite element method, determine the displacement at node 2 and node 3. The modulus of elasticity is constant.
1025ft2 * 8ft = Convert answer to m3
Solve for Mu, if fy = 414 and f 'c = 27.7 -50-100- -9909 -75 250 100- 3 - 28mm Ø2 -75 100- 400- -2-20mm Ø
-F ab)" a~bm X= L+I 2 1 TY –314. F 2. 6 STATICS ENGINEERS MECHANICS CHAPTER Lecture Notes: =m EXAMPLE: 2 mber 75mm 25 mm +3 150 mm P2 25 mm %3D 25mm 125 mm Determine the moment of inertia of the section E+ b about its centroidal axis x and y. + b ナ

3 Homework.pdf 1 من 1 EAAMPLE (1). A circular bar having 200 mm² area is subjected to axial loads as shown in Fig Find the value of ( P) and the total elongation . Take E=2*105N/mm2. A B 50kN 50kN -lokN 1M 1M 1M
Determine the value of the shape factor f. -200mm- 25mm 250mm 25mm 25mm 300mm-
ΕΧΑMPLΕ 1) A circular bar having 200 mm? area is subjected to axial loads as shown in Fig „Find the value of ( P) and the total elongation . Take E=2*10° N/mm?. A в C D 50kN 50kN -lo kN 1M 1M 1M
Question 39/50 Situation 39, 40 10m/s Es=200 GPa E,=105 GPa 50 kg Steel 15 mm-diaBrass k=25 kN/mm 图的的 1.5m 1.5m 0.5m O Zoom image Determine the stiffness of Spring, Steel and Brass assembly as shown. O 8256.25 N/mm O 9141.75 N/mm O 2563.23 N/mm 5632.20 N/mm PreviouIS Next >
a=2 b=5 3xb=15x mm 12xb=60x mm 10xa kN = 20x kN ((3xb)-0,00735)) = (15x- 0,00735) mm
Y Given: X x1 x2 . x1 = 15.35 mm • x2 = 16.74 mm . x3 = 16.10 mm .y1 = 19.32 mm y2 = 20.55 mm y3 = 16.37 mm mie x3 sterren T y3 y2 y1 Find x & y centroid
PROBLEM 2 Compute the design flexural strength of the following sections for flexure Use f, = 420 Mpa f = 28 Mpa (You can assume the cover thick = 40 mm) %3D
A circular stepped steel shaft has the dimensions and cross sections as shown in Figure Q1. It is fixed at its ends A and D and subjected to a torques T=1200NM and T= 400Nm. Take modulus of rigidity, G = 75GPA. Determine the: a) Torsional reactions at A and D b) Angle of twist of B with respect to D, oBD c) Maximum shear stress in the shaft