P9-1 D The steel rod (E= 200GPA) is subjected to the loading shown. If the cross-sectional area of the rod %3D 0.75 m 60° 60° is 60mm2, determine the displacement of B and A, Neglect the size of the couplings at B, C, 1.50 m 3.30 kN 3.30 kN B and D. 3 0.50 m [Ans. Sg = 2.31mm, 8A = 2.64mm] %3D %D 2 kN 2 kN 8 kN

P9-1 D The steel rod (E= 200GPA) is subjected to the loading shown. If the cross-sectional area of the rod %3D 0.75 m 60° 60° is 60mm2, determine the displacement of B and A, Neglect the size of the couplings at B, C, 1.50 m 3.30 kN 3.30 kN B and D. 3 0.50 m [Ans. Sg = 2.31mm, 8A = 2.64mm] %3D %D 2 kN 2 kN 8 kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

What horlzontal force P Is required to hold the 17- Ib welght W in the position shown? 2. 17-b
Determine the maximum safe load P that can be supported by the bolted connection as shown if the maximum allowable shear stress in any rivet is 55 MPa. Under such load, determine the minimum stress developed. 200mm P 400mm 300 mm 300 mm For the location of centroid of the rivet group- For the distance of each rivet from the centroid of the rivet group For the magnitude of the Polar moments of Inertia of the rivet group with respect to its centroid- For the magnitude of P 22 mm
The homogeneous wire ABCD is bent as shown and is attached to a hinge at C. The length BCindicated by b is 94 mm. Determine the length L for which portion BDC of the wire is horizontal. L В IC 60 mm A The length L for which portion BCD of the wire is horizontal is mm.
Use the subsne member to make a compieneanlyss of e comples uss shown 25kN d 3m 25KN 4 m e1.5 m 2 at 4 m = 8 m
4-1. The A992 steel rod is subjected to the loading shown. If the cross-sectional area of the rod is 80 mm², determine the displacement of B and A. Neglect the size of the couplings at B and C. 6kN 45° 5 kN B A 45° 6kN 5 kN 10kN 0.75m 1.50m 1m
Q2: Reduce the system of forces and moment shown to (a) an equivalent two * forces and couple system at A 5 KN 0.5 m 2 m 75° To.15 m 10.15 m 500 N-m ---x 1.2 kN
The bracket BCD is hinged at € and attached to a control cable | ! at B. For the loading shown, determine (a) the tension in the cable, (b) the reaction at C. a=0. 18m 20N 20N 8 c o I_.l_nm—l—um—-l 02¢m
How many zero force members are there in the truss shown? F. [E Hl100 '1 60 VKN kN 60 ♥kN Select one: O a. 4 O b. 2 О с. 1 O d. 3
Draw the FDBS of member ADB and BEC 1 m 1 m В C E 1 m D 1.6 m
Situation 21 A flanged bolt coupling, consists of 20mmo rivets arranged, is used to transfer the Torque T from a solid shaft 80mm in diameter to a 180mm square hollow tubular pipe with unknown thickness T. 3) Determine the maximum applied torque T without exceeding a maximum shearing stress of SOMPA for circular shaft, and 60MPA for the rivets. Gun =83 GPa. 4) Determine the minimum thickness "T" of the tubular pipe with a maximum shearing stress of 70 MPa. 5) Assuming point B is fixed, and the shaft A-B is 300mm long, determine the angle of twist developed at A relative to B. R10 R125 R80 OBT
Two reds vertically connect beam figure. Pcint A is fxed s shinged connected If the rod on the right is heated by 18 degree Celsius 2 m - 2 m 2 m Use E-200 GPa, linear of coeff cient expansion = 11.7x1o per degree celsius and A4509 mm Compute for the deformation of the right rodin mm Select the correct response 0.0234 mm 0.0842 mm 00468 mm 0.117 mm
A GOKN B 1 1 CS Scanned with CamScanner 180 KN } lytie i 1 zmi com ! 4m, alm 1 Read ol 8m Reactions at A and C Tension in the rod