Part A Determine the angular velocity of the generator pulley B, measured clockwise Express your answer using three significant figures. Enter positive value if the angular velocity is clockwise and negative value if the angular velocity is counterclockwise. AE Ivec Submit Request Answer Part B rud/s Determine the angular velocity of the air-conditioning pulley C, measured cleckoise Express your answer using three significant figures. Enter positive value if the angular velocity is clockwise and negative value if the angular velocity is counterclockwise.

Part A Determine the angular velocity of the generator pulley B, measured clockwise Express your answer using three significant figures. Enter positive value if the angular velocity is clockwise and negative value if the angular velocity is counterclockwise. AE Ivec Submit Request Answer Part B rud/s Determine the angular velocity of the air-conditioning pulley C, measured cleckoise Express your answer using three significant figures. Enter positive value if the angular velocity is clockwise and negative value if the angular velocity is counterclockwise.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In the image on the right, there is a red gear G1 on the left with a radius of r1 = 2.81cm. Gear G1 is locked to the green gear G2 with a radius of r2 = 0.734cm. Gear G2 then shares the same axle as the blue circular saw G3, which has a radius of r3 known to make a full rotation every T = 0.836s. Using at least 6 significant digits in your calculations, compute the following: V3! 12.8cm. Gear G1 is W1 a) The angular speed wi of gear G1. Remember that angular speed is measured in radians per T3 r2 unit time. G2 b) The rim speed vi of gear G1. Since gears G1 and G2 are locked together, the rim speed of G2 is also v1. G1 G3 c) The angular speed w2 of gear G2. Since gear G2 and saw G3 share the same axle, the angular speed of G3 is also w2. d) The rim speed v3 of saw G3.
Determine the degree of freedom of the mechanism in the figure below. Then determine all the centers of the era. Then use it to find the angular velocity of link 4 as well as the sliding velocity, knowing w_2 = 10 rad /s clockwise. Note that you must specify the order and method of determining non-obvious centers. %3D PE 4 5 D. C B Link radius 2:-25mm Link radius 5:-10mm BD length: -55 and DE length=30mm its angle with a horizon of 45 degrees and also the radius of curvature of the earth at point F is equal to 20 mm. The segment AB is horizontal and BD is vertical. The contact at point Cis of the rolling type with slip and at point F the rolling is pure. 2.
Given: The four bar linkage is moving with WCD equal to 6 rad/s CCW. Find: The velocity of point E on link BC and angular velocity of link AB. Use ICR method. 30° B 0.3 m 0.3 m E WCD= 6 rad/s 0.6 m
A b a S the slider-crank mechanism is in the position where A =75 Degree and the angular velocity of the link OA is 61.7 rad/s a= 2.9 m b=10 m O =.161.8 Degree s=9.634 m Find the velocity of the slider using the analytical method.
The figure shows a variation of the Scotch-yoke mechanism. It is driven by crank 2 at an angular velocity and acceleration of 36 rad/s ccw and 120 rad/s2 ccw, respectively. Find the velocity and acceleration of the crosshead, link 4.|AO2|=75 mm. (Using Complex Algebraic approach do the Position Analysis; Velocity Analysis and Acceleration Analysis then solve the problem please)
2. Locate the instantaneous center for bar BC. Use it to find the velocity of point C. 6 ft 3ft o=2 rad/sec o-3 rad/sec 6.5 ft Used with permission from "Engineering Mechanics: Dynamics." McGil/King, 4th Ed., 2003 The IC for bar BC is located on a line extended from point A to point B. 4 feet to the right of point B. vc= -9i – 12) ft / see The IC for bar BC is located at point A. ic= -9i - 123 fti sec The IC for bar BC is located on a line extended from point A to point B. 3 feet to the left of point B. vc -6i ft/ sec None of the above
The crank rotates at a rate of 250 rpm. Determine the following:(a) angular velocity of link 4 (O4B), and(b) the velocity of slider C.O2O4 = 47 cmO2A = 15 cmAB = 37 cmO4B = 25 cmBC = 60 cmθ = 600Drawing not to scale. Use with caution. diagram is shown in the picture attached.
Answer the following by using the INSTANTANEOUS CENTER METHOD for Velocity Analysis The mechanism shown is composed of rod GPV pin-connected to rod DPE at point P. Knowing that the velocity of V is 4 m/s downwards, A. [20%] Redraw bar GPV and determine its instantaneous center of rotation (label it as point C). Specify all angles and distances E 300 mm needed. 250 mm B. [15%] Determine the angular velocity of rod GPV. C. [30%] Determine the velocity of point P. D. [20%] Redraw bar DPE and determine its instantaneous center P 400 mm v = 4 m/s 300 mm 30° of rotation (label it as point C). Specify all angles and distances needed. E. [15%] Determine the angular velocity of rod DPE.
PROBLEM 2 For the mechanism, shown on the figure, Onc = const 5 s'. O4=BC D0,3 m, AB-0,6 m. Determine: a) velocity and acceleration of the point B: b) angular acceleration of the body BC: c) angular velocity and angular acceleration of the body OA: d) linear velocity and acceleration of the pointA. 120 60°
A gear system comprises gear A, which is stationary. The bar A'C' rotates with an angular velocity ω1 of 5 rad/s. What will be the angular velocity of gear C? Diameters of the gears: DA = 600 mmDB = 350 mmDC = 200 mm Note: Solve gears B and C by IC method and by relative velocities method
PLANETARY GEARS KINEMATCS The gear is connected to Rack C in the picture shown below. The rope B is attached to the gear at point A. If the velocity of the rope and rack are as shown in the figure below, then what is the velocity and acceleration of point O? What is the angular velocity and angular acceleration of the gear? ay = 1.5 m/s? vn = 3 m/s 0.3 m -0.2 m ac = 0.75 m/s? Ve: = 1.5 m/s
Example: Figure shows the configuration of an engine mechanism. The dimensions are as following. Crack OA = 200 mm, Connecting road AB = 600 mm, distance of center of mass from crank end AD = 200 mm. As the instant, the crank has an angular velocity of 50 rad/s clockwise. Calculate the velocity of D and angular velocity of AB. B G - D 120° @. A