%3D 7- The fan angle of a uniform stream of M1 = 1.6 passing through a convez wedge of 20 degrees is O 33.4 degrees O 17.8 degrees O 40.6 degrees O 26 degrees 8- If you asked to reduce the specific fuel consumption of a turbojet engine by improving the efficiency of either the turbine or the compressor. Which one you will elect? O the turbine the compressor

%3D 7- The fan angle of a uniform stream of M1 = 1.6 passing through a convez wedge of 20 degrees is O 33.4 degrees O 17.8 degrees O 40.6 degrees O 26 degrees 8- If you asked to reduce the specific fuel consumption of a turbojet engine by improving the efficiency of either the turbine or the compressor. Which one you will elect? O the turbine the compressor

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A turbojet engine is travelling at 500 mph with an altitude of 8 km. The jet velocity is 1900 ft/s. The pressure and temperature at the jet exhaust is 4,000 Psf and 800 R. The mass flow is 9300 slugs/hr. a. Calculate the Thrust horsepower. b. What is the propulsive efficiency? c. Calculate the TSFC if the turbojet consumes 15 lb of fuel per hour.
2. Which of the following equations describes the chocked nozzle thrust in a gas turbine engine? O FN=(co-co). Wa FN = (C9 - Co). Wa + (p9 - Po).A9 W. = Wair+Wfuel - Wbleed gas hc = cp.(CPR(1-1/)-1)/hic Wa.hc = (Wa+W+).ht.nm Dikdörtgen Biçin
b) Explain how the following jet engine works. Refer to each section of the engine and explain the purpose of each section. COMPRESSION COMBUSTION EXHAUST INTAKE Air.Inlet Compression Combustion Chambers Turbine Exhaust Cold Section Hot Section Figure Q4b
Arrange 5 steps from beginning to final steps in the diesel engine.
Conceptualize, model and simulate a turbofan engine using any software package
Estimate how the following process modifications affect to the efficiency of the gas turbine process, and connect right answers. Increase of the polytropic efficiency of the turbine Choose... Choose... Increases compressor power Decreases the temperature after turbine Increases the temperature after turbine Reduces compressor power Choose... Reheat combustor Compressor intercooling Increase of compressor inlet air temperature + ◆
LISLUH The following picture is showing different pressure ratios of a Gas Turbine operation. Cycle Il is optimum pressure ratio. Which cycle has the most power output? T T max Tmin Cycle I Cycle II Cycle III 2 W Every cycle has came I net,max II III
2. Which of the following equations describes the chocked nozzle thrust in a gas turbine engine? W₁.hc= = (W₂ +W₂).ht.nm O FN = (Co-Co).W₂ + (p9 - Po).A9 W = Wair + W fuel - Wbleed gas hc = cp.(CPR(7-1/7)-1)/hic O FN = (C9 - Co). Wa
Draw schematic diagrams of a gas turbine system used for i. generating electricity with irreversible (actual) single stage compression, ii. two stages of irreversible expansion with reheat, and iii. a regenerator. Specify the relevant corner points of the process.
Below figure shows Ts diagram of an aircraft engine. Draw the engine diagram only. Answer the following: a) What is TIT and max temperature magnitudein this engine? b) What is the fuel to air ratio in main CC and AB. c) Guess the approximate pressure ratio of the compressor making suitable assumption/data. 06 2000 K 1200 K 03 ATO (combustion) 02 01 565 K Pa 04 5 959 K ATO (afterburning)
what are the range of specific speed of the pelton , francis and kaplan turbine?
You have been asked to help with the low-pressure compressor (LPC) design for a turbofan engine with a bypass ratio of 8.4. The preliminary cycle design calls for the LPC to produce a pressure ratio of 9.4 with the following operating conditions and constraints. .Inlet Conditions TO2 Poz Core Air Mass Flowrate (kg/s) (K) (kPa) 282 24.6 47.0 Design Constraints Maximum Polytropic Efficiency 94.1% Maximum Stage Pr 1.55 Estimate the minimum number of stages required for this LPC. Then assuming the 1st stage of the LPC operates at the maximum allowable pressure ratio, determine the stagnation temperature exiting the 1st stage, and the stage's adiabatic efficiency. Also determine the power (W) required to operate the full LPC (not just 1st stage). Finally, what would be the percent change in the required power if the polytropic efficiency was only 90.0%.