Perform Basic Configuration tasks on MUSCAT-SW1 switch. a) Go to global configuration mode b) Change the name of the device to MUSCAT-SW1 c) Configure the secret password to ha$ik123 d) Set the console 0 password to oman21 and go back to global configuration mode e) Set the VTY 0 4 password to oman21 and go back to global configuration mode f) Configure VLAN 1 with 10.105.29.2/24, activate the interface and go back to global configuration mode. g) Configure the default gateway to 10.105.29.1 h) Set the banner message to #No Entry!# i) Encrypt all plaintext passwords j) Save the running-configuration file k) Display the running

Perform Basic Configuration tasks on MUSCAT-SW1 switch. a) Go to global configuration mode b) Change the name of the device to MUSCAT-SW1 c) Configure the secret password to ha$ik123 d) Set the console 0 password to oman21 and go back to global configuration mode e) Set the VTY 0 4 password to oman21 and go back to global configuration mode f) Configure VLAN 1 with 10.105.29.2/24, activate the interface and go back to global configuration mode. g) Configure the default gateway to 10.105.29.1 h) Set the banner message to #No Entry!# i) Encrypt all plaintext passwords j) Save the running-configuration file k) Display the running

A+ Guide To It Technical Support

10th Edition

ISBN:9780357108291

Author:ANDREWS, Jean.

Publisher:ANDREWS, Jean.

Chapter9: Supporting Mobile Devices

Section: Chapter Questions

Problem 9TC

See similar textbooks

Similar questions

23) Perform Basic Configuration tasks on MUSCAT-SW1 switch. a) Go to global configuration mode b) Change the name of the device to MUSCAT-SW1 c) Configure the secret password to ha$ik123 d) Set the console 0 password to oman21 and go back to global configuration mode e) Set the VTY 0 4 password to oman21 and go back to global configuration mode f) Configure VLAN 1 with 10.105.29.2/24, activate the interface and go back to global configuration mode. g) Configure the default gateway to 10.105.29.1 h) Set the banner message to #No Entry!# i) Encrypt all plaintext passwords j) Save the running-configuration file k) Display the running configuration file
Based on the given tasks, complete the basic switch configuration table below: a. Set the device name to Finance-Sw1 b. Set the secret password to s3cretP@s$ c. Configure the console 0 password to Hol1d@y$ d. Configure the VTY 0 4 password to Hol1d@y$ e. Configure VLAN 1 with 192.168.55.254255.255.255.0 and turn on the interface. f. Configure the default gateway to 192.168.55.1 g. Set the banner message to #Warning, Keep out!# h. Encrypt all plaintext passwords i. Save the running-config file The solution is in the table, please
13. Which of the following statement about the STP is false? OA. The alternate port is the backup port for the RP port. B. If all switches priority are the same, they will compare the MAC address, and the value is the smaller the better. OC. In a new STP network, the first step is electing root bridge, all switches will compare the BID. D. All the port on the root bridge is root port.
When A replies to E, from sw1 to sw2 which switch’s MAC address tables are updated?
Based on given commands below. Identify the main reason of not forming a correct EtherChannel between S1 and S2 switches: s1 (config) # interface range FastEthernet0/0 - 1 S1 (config-if-range) # channel-group 1 mode active s1 (config-if-range) # interface port-channel 1 s1 (config-if)+ switchport mode trunk s1 (config-if) # switchport trunk allowed vlan 1-5,: s2 (config) # interface range FastEthernet0/0 - 1 s2 (config-if-range) # channel-group 1 mode activ s2 (config-if-range) # interface port-channel 1 s2 (config-if) # switchport mode trunk s2 (config-if) # switchport trunk allowed vlan 1, O The EtherChannel was not configured with the same allowed range of VLANS on each interface. The interface port-channel number has to be different on each switch. O The switch ports were not configured with speed and duplex mode. O The switch ports have to be configured as access ports with each port having a VLAN assigned. Which one of the following statements is correct about interior and…
P Flag question On a switch that is configured with multiple VLANS, which command will remove only the VLAN 10 from the switch? a. delete flash O b. no vlan 10 O C. delete vlan 10 d. no vlan
Set up the following:There are two switches on VLans: Switch 1)VLan 10, Dept. Admin (Ports: fa0/1-2)VLan 20, Dept. Account (Ports: fa0/21-23)Switch 2)VLan 10, Dept. Admin (Ports: fa0/1-4)VLan 20, Dept. Account (Ports: fa0/18-23)Trunk: (Port: fa0/24) Note : Perform On cisco packet tracer
Set up the following:There are two switches on VLans: Switch 1)VLan 10, Dept. Admin (Ports: fa0/1-2)VLan 20, Dept. Account (Ports: fa0/21-23)Switch 2)VLan 10, Dept. Admin (Ports: fa0/1-4)VLan 20, Dept. Account (Ports: fa0/18-23)Trunk: (Port: fa0/24)
Write down the commands to configure each step Assuming SW1 is a 24 port switch. Connect PC1, PC2, PC3, PC4 and PC5 on port numbers 6, 8, 13, 17 and 21 respectively. Configure VLANs on SW1 in such a way that PC1 should ping PC2 only and PC3 should ping PC5 only. PC4 should not be able to communicate with any other PC (Note: All ports on SW1 connecting to other switches will be kept in default VLAN) Configure Ether-channel between SW2 and SW6. Show commands.
We have 5 devices connected to an 8-port switch. Each device is numbered starting with 0, and each port of the switch is also numbered starting with 0. Device 0 has MAC address 40-4A-18-B2-63-DA and is connected to port 0 of the Switch. Device 1 has MAC address 00-0C-2B-AF-18-7B and is connected to port 1 of the Switch. Device 2 has MAC address 00-1D-D1-BC-DF-73 and is connected to port 2 of the Switch. Device 3 has MAC address AC-D9-D6-57-24-A3 and is connected to port 3 of the Switch. Device 4 has MAC address 04-5D-56-3E-A3-B4 and is connected to port 4 of the Switch. The switch and all the devices are cold-started, and the following Ethernet frames are sent on the network in sequence: Frame 0 (source 40-4A-18-B2-63-DA destination 04-5D-56-3E-A3-B4) Frame 1 (source AC-D9-D6-57-24-A3 destination 00-0C-2B-AF-18-7B) Frame 2 (source 40-4A-18-B2-63-DA destination 00-1D-D1-BC-DF-73) Frame 3 (source 00-0C-2B-AF-18-7B destination 00-1D-D1-BC-DF-73) Frame 4 (source…
Network latency issues are often caused by SELinux or AppArmor restrictions. True or False?
12, Which statement about the STP port state is false? A. If a blocked port does not receive BPDUs within a specified period, the port automatically switches to the Listening state. B. A port in Listening state keeps listening to BPDUs. OC. The blocked port does not listen to or send BPDUs. OD. A port in Learning state learns MAC addresses but does not forward data.