pg. 437) An acb sequence balanced three-phase Y- connected source supplies power to a balanced, three-phase A-connected load with an impedance of 12+j90/6. The source voltage in the b-phase is 240/-50° V. The line impedance is 1+j10/p. a) Draw the single-phase equivalent circuit for the a-phase. b) Use this drawing to find the current in the a-phase of the load.

pg. 437) An acb sequence balanced three-phase Y- connected source supplies power to a balanced, three-phase A-connected load with an impedance of 12+j90/6. The source voltage in the b-phase is 240/-50° V. The line impedance is 1+j10/p. a) Draw the single-phase equivalent circuit for the a-phase. b) Use this drawing to find the current in the a-phase of the load.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.42P: A balanced -connected impedance load with (12+j9) per phase is supplied by a balanced three-phase...

See similar textbooks

Similar questions

In a balanced delta connected 3-phase circuit, has resistance 25 ohm and inductive reactance 40 ohm, connected to a 400V,50HZ 3-phase supply voltage, then total power delivered to load is Select one: a. 5397.76W b. 1635.34KW c. 7593.26W d. NONE OF THESE
1. The following are the given for the circuit below: VRY = 220 cis 0°, VYB = 220 cis -120° and VBR = 220 cis -240°. IR = 10 cis 0°. The load is balanced and delta connected. Determine the: (a) Impedance per phase (b) Current per phase (c) Line currents. B R reellle relllle momm Y RY Iy IB ĪR B R ZBR VYB ZRY
The Figure shows a balanced Y-A 3Ø circuit. The phase voltages of the Y-connected source are V, = 11020°, V, = 1102 - 120° and V. = 1102120°, Volts. The line impdedances are Z,=10+j5 Q each. The impedances of the A-connected load are ZA = 75+j255 N each. Determine: Line Currents, Phase Currents (load), Power drawn by the load. Ve ZA Vb
13. In parallel-connected ac circuit, the total current though the circuit is always equal to the phasor sum of the individual current though each element. True False 14. In a R-C parallel circuit, R=10 ohms and Xc=10 ohms, the applied voltage is leading to the circuit total current by 45 degrees (assumed applied voltage is the reference). True False 15. In a R-C series circuit, applied voltage is in phase with the total current. True False
5.In three-phase transformers, the high voltage star connection is preferred. This is so because in this case A) The voltage on the star windings is lower than if they were in delta and this reduces manufacturing costs. B) The voltage on the star windings is higher than if they were in delta and this reduces manufacturing costs. C) The voltage on the star windings would be the line-to-line voltage of the system since it is a three-phase manufacturing transformer. D) THERE IS NO SOLUTION
A three-phase system has balanced conditions so that the per-phase circuit representation can be used as shown in Figure 1 Select the turns ratio of the step-up and step-down transformers that the system operates with an efficiency greater than 99 percent. Moreover, find the complex power (received or given) of all components in the circuit and the V1 and V2 voltages. The load voltage is specified as 4 kV rms, and the load impedance is 4/3 ohm. ..
Two delta connected loads are connected in parallel and powered by a balanced Y-connectedsource. The smaller of two loads draws 10 kVA at a lagging power factor of 0.75 and the largerdraws 25 kVA at a leading power factor of 0.8. The line voltage is 400 V. Calculate a) The powerfactor at which the source is operating. b) The total power drawn by the two loads. c) The phasecurrent of each load.
In the circuit in the figure; L1 load draws 15 kVA with lagging power factor 0.6. The L2 load draws 6 kVA with a leading power factor of 0.8. According to this; What is the value of the complex power for the L2 load?
Three Impedances each of (8 - j24)2 are connected in mesh across a three-phase 420V ac supply. Determine the phase current, line current, active power, reactive power drawn from supply. Also draw the Phasor diagram for the mesh connection and marks the Line current ,phase current line voltage and phase angle between phase current and pahse voltage. phase current (Ip) Line current real power reactive power
Draw Wye- Delta three phase transformers connection ( no-load and full-load) in Lt-spice
A workshop from a 231/400 V transformer center with a 3-phase and four-conductor underground cablefed. The resistance of the phase conductors is 0.035 ohms and the resistance of the neutral conductors is 0.05 ohms.25 kVA at 0.8 reverse power factor from R phase of the supply line, 0.8 forward power factor from S phase 15Fully ohmic loads of 10 kVA are drawn from kVA and T phases.(a) Find the currents flowing through the phase conductors and neutral conductors.(b) Voltage drops between the transformer substation and the workshop and at the load terminals.calculate the voltages(c) Plot the supply line currents and phase voltages phasorally.
A 3-phase delta connected load is supplied by a 11/0.4 kV, star-delta connected transformer. The load impedances are Z1 = 20 + j0 ohms, Z2 = 10 – j5 ohms and Z3 = 15 + j10 ohms. Determine the line currents and also currents in the secondary windings of the transformers