Please do 6-6 4 ftkip.ASEYCHEST1.5 m10 ftB10 ft2 mProb. 6-410 ft6-5. Determine the force in each member of the truss, andstate if the members are in tension or compression. Set 0 = 0°.6-6. Determine the force in each member of the truss, andstate if the members are in tension or compression. Set 0 = 30°.B4 kN4 kNProbs. 6-5/6D3 kN2 m-10 ftE6-7.Determine the force in each member of the truss andstate if the members are in tension or compression.

Given data:- Load 3kN and 4 kN Dimensions Angle 30° To find out Member forces

Answered: 6-6. Determine the force in each member…

6-6. Determine the force in each member of the truss, and = 30⁰. state if the members are in tension or compression. Set

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 2. Determine the forces in members GF, FC and CD. State if the members are in tension or compression…

Q: Determine the support reactions for the below problem. Draw all appropriate FBD. PIN w 10¹ ROLLER…

A: Given, Beam 'AB' has Uniformly distributed load of 2k/ft. Beam 'CD' has Inclined load of 5k at 5ft…

Q: What is a multipurpose river valley project? Give any four objectives of the multipurpose river…

A: Introduction: Hydrology: Hydrology is the science that includes the presence, distribution, movement…

Q: 1. Draw the shear and moment diagrams of the following beam loaded as shown. Also indicate the…

A: Given data Draw shear force and bending moment diagram.

Q: 1.0 A RECTANGULAR GATE 2.0 M X 5.0 M IS ACTED ON WATER ON ONE SIDE AND IS POSITIONED WITH ITS LONGER…

Q: Why can't aesthetic features affect the stability of the bridge?

A: The essential components of a bridge are girders, piers, towers, and just maybe cables. The piers as…

Q: A total station instrument occupies control point 20 and takes a BS to CP 22. The Azimuth from 20 -…

A: The backsight of CP-20 to 22 = 215°55'00'' Easting and northing of CP-20 = 8000,13000 The included…

Q: Water flows from the tank shown in the figure below. At a depth of 1.5 ft the rate of change of…

A: Answer we are given h =1.5 ft rate of change of depth = -0.004 ft/s diamter of pipe d = 0.5 in…

Q: A given reactant decomposes in water with a first-order rate constant of k = 0.43 s-1. If a feed…

A: Given Data : Rate constantk=0.43 s-1 Inital ConcentrationA∘= 1.0 mol/L Rate (Q)=0.1 m3/s

Q: Consider 5.0 pounds per minute of water vapor at 100 lb/in2, 500°F, and a velocity of 100 ft/s…

Q: Workout 2. Use the area-moment method to determine the slope and deflection at point B of the beam…

A: Given data Find slope and deflection at B using Area-moment method.

Q: Figure P- 4.5 ft 1.5 ft 1.5 ft A 2.5 ft + 3.5 ft Part B Determine the maximum force P that can be…

Q: A solid shaft of 100mm diameter of a small hydraulic turbine is subjected to an axial compressive…

Q: A 30-m steel tape at 20°C is used to measure a rectangle whose sides were recorded as 144.95m and…

A: Given,

Q: DRAW THE SHEAR AND MOMENT DIAGRAM OF THE BEAM LOADED AS SHOWN BELOW AND DETERMINE THE VALUE OF Vmax…

A: Given data Last 2 digit = 59 So, 4+59 = 63 KN/m 5+59 = 64 KN 8+59 = 67 KN/m Draw shear force and…

Q: . A commercial truck parks in a house driveway to complete a delivery. The driveway borders one side…

Q: An oil pump operating at steady state delivers oil at a rate of 10 lb/s through a 1-in.-diameter…

A: Given data in question Diameter 1 in Mass flow rate 10 lb/s Density 70 lb/ft3 Pressure rise 40…

Q: In a railroad layout, the centerlines of two parallel tracks are connected with a reversed curve of…

Q: Survey Question: A total station with a 20"/div. level bubble is one divisions out of level on a…

A: Given: Total station bubble sensitiveness, s = 20''/ div. Altitude angle, θ = 49o 25' 24'' To find:…

Q: -1 1. The shear diagram of a beam is shown below. Draw completely the given beam including all the…

A: Given data Shear force diagram Draw loading diagram and bending moment diagram.

Q: Determine the resultant and the moment of the system of forces with respect to point B with b = 1.0…

Q: termine the horizontal and vertical components of reaction at the pins A, B, and C.

Q: Solve the slope and deflection at points B and C using the Double Integration Method. Point B is at…

A: E = 200 GPa I = 7.5 x 10-6 m4 Beam is symmetrical about C (mid-section) This, the deflection curve…

Q: Use the area-moment method to determine the slopes at end A and the deflections at points B of the…

A: Given data Find slope at A and deflection at B using Area-moment method.

Q: A rectangular beam reinforced for both tension and compression bars has an area of 1450 mm² for…

A: Answer To calculate the maximum service load P we need to equate maximum moment on beam due to load…

Q: Determine the resultant of the three forces shown in the figure. 我 3m 2m 2m 2m CO P=18kN A 12kN 2m…

A: Given: Required: Resultant of the three forces shown

Q: What is the tallest a 24in square concrete column with fixed-fixed end conditions can be and still…

A: As per authoring guidelines, if the question number is not specified, the first question or three…

Q: 1. Determine the support reactions of the parabolic arch shown below and the internal forces at a…

Q: Air enters a compressor operating at steady state at 15 lbf/in.2, 80°F and exits at 200°F. Stray…

A: Given Pressure at entrance= 15 lbf/in2 Temperature at entrance= 80°F

Q: Two couples act on the frame. If d = 4 ft, determine theresultant couple moment. Compute the result…

Q: Determine the z-coordinate of the mass center of the homogeneous paraboloid of revolution shown…

Q: For the truss shown below, determine the horizontal deflection at joint E using A=3750 mm² for all…

Q: For the cantilever beam loaded as shown, find the deflection at the free end and the slope at point…

Q: How does the history affect the future practice and development of Civil Engineering in the…

A: Brief concept introduction- Civil Engineering- A profession in civil engineering includes designing…

Q: 5. Determine the forces in the members ientified by “X” of the truss shown using method of sections

A: Given data in question Load 30 kN Dimensions To find out Member forces marked X

Q: A line of levels is run from BM1 to BM2 that is 8 km long. Elevation of BM1 and BM2 was found out to…

Q: Determine the force in member DE of the truss shown. State if the members are in tension or…

Q: A simple horizontal curve of radius 350 ft connects two tangents that form an intersection angle of…

Q: Hi for fy in step 2 why do you add 5?

Q: The point of zero moment is the O Point of Zero Shear Point of Maximum Shear Point of Minimum Shear…

A: The bending moment passes through zero along the length of beam ,these point are called points of…

Q: Adjusted Distance The adjusted latitude and adjusted departure for a line is given as: Adjusted…

Q: 3. Determine the force in CD of the cable if the force in BC is 34 lb. 7 ft 34 15 B 50 lb

A: Given : Force in BC = 34 lb Determine force in CD ?

Q: Compare and contrast the differences between post-tensioning and pre-tensioning with supporting…

A: When in concrete where internal stress of suitable magnitude and distribution is introduced, the…

Q: Determined and fil-up the unknown data of the given table. Physical Properties Mix Design Specific…

A: Concrete Concrete is a composite material used in engineering that closely resembles rock in its…

Q: -X- 20 kN 4 kN/m 10 m- 20 kN

Q: using tape standardiz ull of 10kg. The recorded distance was found out to be 430.60 meters. At the…

Q: The weight of the spring held follower AB is 0.317 kg and moves back and forth as its end rolls on…

Q: P20,000 for 10 years with the first payment to be made one year after his retirement. The…

Q: An ideal Rankine cycle with reheat uses water as the working fluid. As shown in the figure below,…

Q: Consider the average annual growth rate 5.93% of 2000-2005, and forecast the population in Abu Dhabi…

A: National Non national Total 1980 90792 361056 451848 1985 135982 430054 566036 1990 173992…

Concept explainers

Types of Composite

Composite materials are formed by merging two components that have different chemical and physical properties. The merged output is termed as a composite, whose properties are completely different from the individual components. Composite materials also have better strength than the individual components.Composite materials usually have two main parts, reinforcement material, and matrix material. The matrix material acts as a binder and surrounds the fiber of another material that bears a much higher strength. This material is known as the reinforcement material. The matrix materials are usually high-strength additives resins, while the fibers of the reinforced material can be random, oriented, and in a mat format.Composite materials are also known as fiber-reinforced composite polymers because they are composed of the polymer matrix which is reinforced to laboratory-created fibers or naturally occurring fibers, such as glass fibers, carbon fibers, or aramid fibers. Under the application of external loads, the matrix material absorbs and transfers the loads to the fibers, these fibers in return provide good compressive strength, tensile strength, and stiffness to the fiber-reinforced composite materials.Depending upon the matrix and the reinforcement material, different properties can be induced to the fiber-reinforced composite materials, including good corrosion resistance properties. The most common matrix material is the resin while the glass fibers act as the reinforcement material. Strong fibers provide strength and stiffness to the composite materials while, a soft and flexible resin provides shape to the composite materials.

Question

Please do 6-6

4 ft
kip.
A
SEYCHEST
1.5 m
10 ft
B
10 ft
2 m
Prob. 6-4
10 ft
6-5. Determine the force in each member of the truss, and
state if the members are in tension or compression. Set 0 = 0°.
6-6. Determine the force in each member of the truss, and
state if the members are in tension or compression. Set 0 = 30°.
B
4 kN
4 kN
Probs. 6-5/6
D
3 kN
2 m
-10 ft
E
6-7.
Determine the force in each member of the truss and
state if the members are in tension or compression.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

500 N 400 N 2.598 m 600 600 600 600B RAH 3 m AV - 201.8 N 298.2N Determine the force in mnember DE of the truss shown. State if the members are in tension or compression.
1000 N 3000 N 1000 N b E b 1000 N F D 30 a В -2 m --2 m-–2 m--2 m 4000 N 2000 N Determine the force in member EB of the roof truss shown by method of sections. Indicate whether the member is in tension or compression.
4 kN 4 kN 3 kN 2 kN B C D 3 m H 2'm - 5 m- -5 m- -5 m- - 5 m- Q4- The figure shows a truss that is supported at A by a pin and a roller at E. The truss is subjected to vertical forces. Determine the following: (a) check for zero-force members and identify such members (b) The Force Reactions at the supports are: Ax kN Ay kN Ey k N (c) The internal Force in member CD, FcD i . kN, specify (T) or (C) (d) The internal Force in member CF, FCF İS. . kN, specify (T) or (C) (e) The internal Force in member CD, FcG is . kN, specify (T) or (C)
Determine the force in members EF, EP, and LK of the Baltimore bridge truss and state if the members are in tension or compression. Also, indicate all zero-force members. M L. K 2,m N P 2 m A B C DE F G H 2 kN 2 kN 5 kN 3 kN 8 @ 2 m = 16 m %3D
6- The truss shown is used to support the floor deck. The uniform load on deck is 2.5 k/ft. This load is transferred from the deck to the floor beams, which rest on the top joints of the truss. Determine the force in each member of the truss, and state if the members are in tension or compression. Assume all members are pin connected. 2.5 k M K 12 f1 3 C D E F 6@ 12 ft 721
3-23. Determine the force in members EF, EP,and LK of the Baltimore bridge truss and state if the members are in tension or compression. Also, indicate all zero-force members. M L. K 2 m N. P 2 m A В D E G 2 kN 2 kN 5 kN 3 kN 8 @ 2 m = 16 m- Prob. 3-23
For the type 1 compound truss shown, determine the force in each member and state if the members are in tension or compression. The internal angle between any two members is 60°. The truss is pin supported at A and roller supported at F. Use X = 2 and Y = 7. J A. H. 1x. YY kN 7.XY kN 1Y. XX KN
Determine the force in each member of the truss and state if the members are in tension or compression. Set P₁ = 7 kN and P₂ = 7kN. A P₁ -2 m- D P₂ B 2m
10-29. Determine the force in each member of the truss. Assume the members are pin connected at their ends. AE is constant. (1) 10 kN 2 m — E 2 m 20 kN D 88888 &28 888 B 2m 15 kN to GR
1.18 Determine the truss's smallest safe cross-sectional areas of member's CD. Ch. and GF. In tension, the working stresses are 140 MPa, while in compression, the are 100 MPa. (In compression, the working stress is smaller to reduce the risk of buckling.) B D. 311 3n 2n 2ft 3ft H 3ft G 3t 3t 120KN 120KN V
ment 6 3. Find all the support reactions A and N and also calculate all the internal forces in the truss and state whether in tension or compression. Use either the method of joints or sections. Consider JY = YN = NJ, LO = ON = NL = JP = PL = %3D LJ = GQ = QJ = JG and OL // JY //GX. U V W X Y P в сD E FGH J KL M 100 kN 100 kN
DETERMINE THE STRESS IN EACH MEMBER OF TRUSS LOADED AND SUPPORTED AS SHOWN. - 4m Am 104N D 10 KN 4m Epanels@4m = 20m E B 4m LL G 604N → 60 kN