Please explain this What do the following instructions do on a PDP-8 processor?  111010000000 111110000000

Q: In Assembly Language Design the ALU in emu 8086 that perform the following functionalities:  Take…

A: Assembly Language  Assembly language is a low-level programming language. The system bus connects…

Q: write Assembly code that processes an text input, each arithmetic operation should be performed…

A: We will use different programs for all arithmetic operations.

Q: . In processors prior to the P6 family, which instruction compares two floating-point values?

A: Instruction comparing two floating point values FCOM instructions perform the same operation as the…

Q: The assembly code shown below executes the equation for Y = X - W * Z according to  what…

A: Given equation: Y = X - W * Z Assembly code: a.Push W  b.Push Z c.MUL d.Push X e.Sub  f. Pop Y  It…

Q: Given below is an example machine instruction. Write the maximum number of operations that can be…

A: Actually, one byte= 8 bits.

Q: Write assembly language instructions that calculate EAX * 24 using binary multiplication.

A: Binary multiplication for EAX*24: The Binary multiplication uses the SHL instruction to perform the…

Q: MIPS instructions require having access to memory twice?

A: MIPS instructions require having access to memory twice

Q: Given the assembly code: org 8000h ld a,5 loop: dec a jp p, loop halt Explain what each line does.…

A: An assembly code is provided to be discussed. The code uses the instruction sets of the Z80…

Q: what is register $1 after these instructions? addi $1,$0,15 srl $1,$1,2 A-0x00000000…

A: According to the information given:- We have to define correct option to satisfy the statement.

Q: The following is a RISC mini-SPARC instruction given in HEX: A8 23 60 D1 a) To what family of…

A: Answer: Our guideline is answer the first three subparts form the first part. Given A8 23 60 D1

Q: What is the value in the x1 after executing the following * :instructions Address Instructions…

A: The instructions given is:- Address Instructions 0x1008 lw x4, 4(x11) 0x1004 jal x1, P1…

Q: n emu 8086......Write the instructions to put the sum of 0+4+8+…. +64 in the DX register. (No need…

A: In emu 8086......Write the instructions to put the sum of 0+4+8+…. +64 in the DX register. (No need…

Q: Write a program that adds the contents of ax register 5 times into bx register. Using 8086 emu and…

A: Write a program that adds the contents of ax register 5 times into bx register.

Q: What is the addressing mode for the following 8085 Assembly language instruction  PUSH A

A: Answer is Direct addressing mode

Q: MANUALLY decode the following ARM machine language code to ARM assembly instruction. 0XE5532911…

A: The machine language is basically the language understandable by machines. It is not readable by…

Q: Explain what each of the following two instructions is telling the processor to do, and what the…

A: According to the information given:- we have to explain the mentioned instruction will perform and…

Q: [5] Write the following code segment in MARIE s assembly language: if X>1 then Y =Y+X; X-0 endif,…

A: Given data, if X > 1 then   Y = Y + X;   X = 0;endif   Y = Y+1;

Q: LDA addr and STA addr are Fortran language instructions stored in an external memory IC for a…

A: Fortran language is an old and previous version of C. It is high level language whereas…

Q: How many MIPS ASCII Characters can fit inside a MIPS CPU's general purpose register? O 4 О 12 O 8 О…

A: 1) MIPS CPU has thirty-two general purpose registers 2) Each general purpose registers 32-bit long…

Q: Machine language form of a jump instruction (j) is 00001001001100101000110001010110. The address of…

A: In the above instruction first 6 bits represent the opcode of the instruction and the remaining 26…

Q: How do I decode the NIOS II machine code 0x1845c83a into an instruction?

A: I have answered this question in step 2.

Q: What is the final value of register $10 after the given sequence of instructions are completed?…

A: 1)  addi instruction: addi instruction is used to add on the content of source register and…

Q: Give an example of a RISC I instructions that will perform the following operations. a. Decrement a…

A: Answer: Our instruction is answer the first three part from the first part and I have explain in…

Q: a) Write a MARIE assembly program that asks the user to input positive numbers A and B. The program…

A: Here are the two numbers  One is A and another one is B and all these numbers are positive numbers.…

Q: Q2) A- Write an 8086 assembly language program to implement the circuit shown in the figure below.…

A: Here we have to implement the above logical circuit to a 8086 assembly language program. In this…

Q: assembly code

A: Given :- In the above question, the statement is mention in the above given question   Need to write…

Q: In latest generation computers, the instructions are executed  Both sequentially an parallely why?

A: In latest generation computers, the instructions are executed  Both sequentially an parallelly

Q: An 8085 microprocessor executes the following instructions: Two numbers are represented in signed…

A: The answer is

Q: What instruction format is this? (one letter) Write out the full instruction in MIPS assembly…

A: What instruction format is this? (one letter) --> There are three instruction categories:…

Q: The 8085 programming manual says that it takes seven T States to fetch and execute the MOV…

A: GIVEN: The 8085 programming manual says that it takes seven T States to fetch and execute the MOV…

Q: If the clock rate of a TMS320C64xx DSP is 600 MHz, how many instructions can it provide to the CPU…

A: It is given that :- The number of bits in an instruction of a TMS320C62xx digital signal processor,…

Q: How many operands does each of the following instructions have? DEC

A: The instruction is the set of the codes which the computer processor can understand.

Q: What MIPS instruction does the following 32-bit binary number represent? 00000001011 01110 00000…

A: 1) MIPS Instruction Format Instructions are 32 bits long. All instructions have an opcode (or op)…

Q: If the CLK input to the 8086/8088 is 4 MHz, how long is one bus cycle? How much time is allowed for…

A: 1 Machine cycle = 4 T states                           = 4 Clock Pulse Frequency = 4 MHZ -> 1…

Q: What is the address of left instruction for and what ís the address in HEX number? Left Instruction…

A:

Q: Q3) Given the following MIPS Instructions: Memory address MIPS instruction 0x00403000 loop: add $a0,…

A: Address of label loop = 0x00403000Address of instruction bne $a0, $zero, loop is 0x00410000 Target…

Q: Q2) What is the addressing mode of each of the following instructions: a- INR C b- MVI M,00 e- RAL…

A: NOTE: Based on our rules, when multi-part questions are posted, we should answer only the first…

Q: Microprocessor 8085 : Note 1: Use F for fetch, R for memory read, W for memory write, IOR for IO…

A:

Q: What will be the values of EDX:EAX after the following instructions execute?mov edx,100hmov…

A: The value of EAX will be F0000000h and the value of EDX will be 000000FFh.

Q: What is the difference between branch instructions and jump instructions?

A: Difference between branch instructions and jump instructions

Q: Given the following mathematical expression in assembly language. MOV AH,01101010b MOV DH,01101001b…

A: Assembly language is a  symbolic representation of machine language. As we know compute can only…

Q: Take two numbers as input, multiply them, print the message “The product is” and then display the…

A: a program should be written in emu8086 such that user needs to input two numbers, then multiply then…

Q: If the current value of the PC is OX57F0_3280, can you use a single jump instruction to get to the…

A: Each machine cycle executes one machine instruction. At the top of the machine cycle, the PC…

Q: program

A: "How does 8051 block access to C: 0000H which resulted in data retrieval from D: 00H?" The answer is…

Q: Using a state diagram, distinguish between the Instruction cycle and the Interrupt cycle.

A: DIFFERENCE BETWEEN INSTRUCTION CYCLE AND INTERRUPT CYCLE -  INSTRUCTION CYCLE -  In the instruction…

Q: Write a Assembly language program for 8086 to find the cube of a number using MUL instruction.

A: Dear Student, 8086 program to find the cube of number is given below, here the value whose cube we…

Q: What is the active frequency of an 8085 microprocessor if the feeding frequency is 4MHZ O20MHZ…

A: Find the required answer with reason given as below :

Q: MANUALLY decode the following ARM machine language code to ARM assembly instruction. Ox34532911…

A: The instruction given is -  0x34532911

Q: Explain the operation of the each of the following instructions of 8051 microcontroller. (i)  MOV…

A: i) The MOV instruction moves data bytes between the two specified operands. The byte specified by…

Computer Fundamentals

The computer is termed computation. For calculating or computing something the device that has been used is known as the computer. Or we can say that for performing a fast arithmetic operation the device that has been used is a computer. Storing, processing, and retrieving are the main features of a computer.