Pressure drop AP depends on four variables: the diameter of the pipe D, the density of the fluid p, the kinematic viscosity of the fluid v and the mean velocity v. Applying Buckinham's Pi Theorem, a dimensionless pi-group can be identified using the following power product: [AP] = [D]ª[p]b[v][v]ª. Which of the following statements in term of [T] is correct? Select one: O [T]: -2 = -c-d [T]: -1 = -c-d [T]: -2 = -c-2*d [T]: -2 = -2*c-d [T]: -2=-c+d

Pressure drop AP depends on four variables: the diameter of the pipe D, the density of the fluid p, the kinematic viscosity of the fluid v and the mean velocity v. Applying Buckinham's Pi Theorem, a dimensionless pi-group can be identified using the following power product: [AP] = [D]ª[p]b[v][v]ª. Which of the following statements in term of [T] is correct? Select one: O [T]: -2 = -c-d [T]: -1 = -c-d [T]: -2 = -c-2d [T]: -2 = -2c-d [T]: -2=-c+d

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. Consider the following equation. All three of the terms in parentheses are dimensionless groups. Because kc is difficult to determine directly, the other variables are measured and kc is calculated from the given equation. 26 THERMODYNAMICS 1 MODULE 1 FUNDAMENTAL CONCEPTS ]3 [ _d>vp_jo8 p DAB kc D = 0.023 [H DAB What is the estimated value of kc? What are the units of kc? Show your work. The following values were measured: D = 8.0 mm, DAB = 0.475 cm²/s, µ = 1.12 x 103 N-s/m², p = 1.00 x 10-³ g/cm³, v = 15.0 m/s.
physical quantities m, r, u, a, and t with dimensions [m] = M, [r]= L, [v] = LT, [a] = LT-2, and [t] = T. Enter the dimensional expression of the quantity on the right-hand side of each equation. Your answers may contain only M, L, T, and exponents. Assume that each of the following equations is dimensionally consistent. F = ma [F] =
To understand the heat transfer from a bar in cross flow, you conduct a series of experiments measuring the average heat transfer coefficient as a function of the free stream velocity. A schematic of the experiment and the accompanying results are shown below. L = 0.3 m h [W/m²-K] 60 40 V [m/s] 20 15 a) You expect the important dimensionless parameters to be related by a function of the form Nu = CRe Pr where C, m, and n are constants. The film temperature in both the experiments is approximately the same. Use the given experimental results to determine the constant m b) Calculate h for L = 0.75 m and V = 30 m/s.
.(b). A force acts on a 2.80-kg particle in such a way that the position of the particle as a function of time is given by x = Find the work done by the force during the first 4.0 s. [4,3] [CLO 3] (3t - 4t²+ t³). Answer
A constant volume gas thermometer is used to determine the temperature of an unknown fluid. Pressure data for thermometer in the unknown bath (P) and a Triple Point Cell (P) are given below. P[Torr] 100.0 P [Torr] 127.9 200.0 256.5 300.0 385.8 400.0 516.0 What is the temperature of the unknown fluid bath? explain and show all work please and write clearly
You must select a submerged centrifuge multicellular pump for a borehole on a worksite that requires a flow of 1.500l/s. The borehole itself is 150m deep (see figure 5). If the outlet pipe has the following properties, then: wwww wwwwwww Water outlet (open air) wwww Outlet pipe L = 200m Borehole wwwww Pump f= 0.04 D = 38mm Figure 5 Borehole and pumping schematic A) Choose a pump from those presented in figure 6 (you must select the most adequate model) if there is no local head-loss, only friction related head-loss. You must draw the complete characteristic curve for the pipe directly on figure 6.; B) Is cavitation an issue if NPSHrequired is 5m briefly discuss the results. C) Determine the supplied power output by the pump (in kW) as well as the absorbed power output when the pump reaches it's operational flow for the pump you have selected. | N.B. Hypothesize that water in the borehole is level with the pump intake. The pump intake is the same diameter as the outlet pipe. Patm-100…
A heat generating slab with thermal conductivity of k [W/m-K] and heat generation rate d" [W/m³] is perfectly insulated on the left side (x = 0) . h1 and is exposed to air with ambient temperature T1 [K] and convection coefficient of hi [W/m²-K] on the right as shown in Fig. 1. Neglect Air Slab radiation. Find out the temperature distribution (i.e., temperature as X= () a function of x) within the slab in terms of the variables shown in the Figure 1: Note the figure. indicated positive direction for reference. SPerfect Insulation
A graphing calculator is recommended. If a rock is thrown upward on the planet Mars with a velocity 8 m/s, its height in meters t seconds later is given by y (a) Find the average velocity (in m/s) over the given time intervals. (i) [1, 2] (ii) [1, 1.5] (iii) [1, 1.1] (iv) [1, 1.01] (v) [1, 1.001] m/s m/s m/s m/s m/s (b) Use your answers from part (a) to estimate the instantaneous velocity of the rock (in m/s) when t = 1. m/s = 8t - 1.86t². (Round your answers to two decimal places.)
1- The thrust (P l ) of a propeller depends upon diameter (D); speed (u) through a fluid density (p); revolution per minute (N); and dynamic viscosity (u) Show that: P = (p D² u²) f P Du [; where fis any function.
The Antoine Equation can be used to estimate vapor pressure at various temperatures for different substances using sets of empirically-derived constants. The equation can be written as: Where for water A = 8.07131, B = 1730.63, C = 233.426, T = temperature [°C], and P = vapor pressure [mmHg]. Note that with these constants the temperature and pressure must be provided in °C and mmHg, respectively. Using the Antoine Equation and the provided constants, what atmospheric pressure (provided in terms of % of standard atmospheric pressure) will permit water to boil at 75 °C?
Analyze the free-body diagram, given the coefficients of static and kinetic friction. Determine whether the block will slide and the net force on the system. static kinetic Hs = 0.25 friction is not shown, but must be incuded in calculations Hk = 0.2 fs,max = 50 %3D fr = W2 [N] slide? friction [N] friction direction | Fnel [N] 40 yes, down-righ 40 up-left v 22 W.-102 W2 W = 200N 50 up-left v (see table) 80 no W = 225N 50 down-righ no 120 18 40 down-righ 160 yes, up-left v 58 40 down-righ v yes, up-left annot be de 200 check answers
Check the following equation for dimensional homogeneity: mu = (Fcos) at where m is mass, v is velocity, F is force, is an angle, and it is time. Check that each term in the equation has the following dimensions: [MOLT] where you are to choose the coefficients a, b, c. Answers: b= C= i i