Prob. 2.2-5. A solid brass rod AB and a solid aluminum rod BC are connected together by a coupler at B, as shown in Fig. P2.2-5. The diameters of the two segments are d = 60 mm and d2 = 50 mm, respectively. Determine the axial stresses oI (in rod AB) and o, (in rod BC). (1) B 150 kN (2) 50 kN P2.2-5 ミー

Prob. 2.2-5. A solid brass rod AB and a solid aluminum rod BC are connected together by a coupler at B, as shown in Fig. P2.2-5. The diameters of the two segments are d = 60 mm and d2 = 50 mm, respectively. Determine the axial stresses oI (in rod AB) and o, (in rod BC). (1) B 150 kN (2) 50 kN P2.2-5 ミー

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

THE DIAGONAL MEMBERS IN THE CENTER PANELS OF THE TRUSS SHOWN ARE VERY SLENDER AND CAN ACT ONLY IN TENSION; SUCH MEMBERS ARE KNOWN AS COUNTERS. DETERMINE THE FORCE IN MEMBER DE AND IN THE COUNTERS THAT ARE ACTING UNDER THE GIVEN LOADING. (15 PTS) Counters ARA B F 6 ft H C E G 3 kips 6 kips 9 kips -S ft- <8 ft- S ft→|<-S ft-
The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E = 90 GPa] with a cross-sectional area of A1 = 510 mm². Bar (2) is an aluminum alloy [E = 68 GPa] with a cross-sectional area of A2 = 320 mm². A concentrated load of P - 75 kN acts on the structure at D. Assume L1-840 mm., L2-420 mm., a-650 mm., b-260 mm., and c-1070 mm. Determine: (a) the normal stresses o1,02 in both bars (1) and (2). (b) the downward deflection vp of point D on the rigid bar. L2 B b D Answers: (a) oi = i MPa, 02 = i MPa (b) VD - i mm.
The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is bronze [E = 113 GPa] with a cross-sectional area of A₁ = 600 mm2. Bar (2) is an aluminum alloy [E = 77 GPa] with a cross-sectional area of A2 = 300 mm². A concentrated load of P = 56 kN acts on the structure at D. Assume L₁-800 mm., L₂-580 mm., a-570 mm., b=340 mm., and c=1090 mm. Determine: (a) the normal stresses 0₁, 0₂ in both bars (1) and (2). (b) the downward deflection VD of point D on the rigid bar. a 5 Answers: (a) o₁ = (b) VD= i i e L₁ L2 A B C C MPa, 0₂ = mm. i D P MPa
Q2/ Segments AB and BC of the assembly below are made from 6061-T6 aluminum. If a couple forces P = 5 kip are applied to the lever arm, Determine (a) the reactions at the fixed supports A and C and (b) the shear stress developed at a point located 1 in. from the center-line of the bar at a cross-section close to point A. 2.5 fi 2.5 ft 6 ft 4 in. 4 in.
The horizontal bar ABC is supported by a pin at A and two rods with identical cross- sectional areas. The rod at B is steel and the rod at C is aluminum. Neglecting the weight of the bar, determine the force in each rod when the force P = 80 kN is applied. Use Est = 200 GPa and Eal = 70 GPa. %3D Steel Aluminum A B T2 m- 1.5 m- Im
Aen = a0 © @2 Z Q23-7-2018p.. Q1: A railway ridge consisting of truss construction as shown in the Figure below, this truss is supported by A and B. The forces on joints il and V are i the uss result from a i crossing the railway bridge Determine the following: (a)the reactions forces in A and B (b)the forces of the truss members in joints (1.1, I and 1V) >
The aluminum rod AB (G = 27 GPa) is bonded to the brass rod BD (G = 39 GPa). Knowing that portion CD of the brass rod is hollow and has an inner diameter of 40 mm, determine the angle of twist at A. 60 mm ----- T - 1600 N - m 36 mm T = 800 N . m 250 mm B 375 mm A 400 mm
Two forces of magnitude TA = 6 kips and Tc = 9 kips are. applied as shown to a welded connection. Knowing that the connection is in equilibrium, determine the magnitudes of the forces Tg and Tp- %3D 40 To Tc
(c) The rigid bar ABC is suspended from three wires of the same material. The cross- sectional area of the wire at B is equal to half of the cross-sectional area of the wires at A and C. Determine the tension in each wire caused by the load P shown. ----|--²--| A 9 DAB T L P Fig. Q1(c) PL Hint: S = note that ABC is a rigid bar. EA C
The aluminum rod AB (G=27 ???) is bonded to the brass rod BD (? =39 ???). Portion CD of the brass rod is hollow and has an inner diameter of 40 mm. Determine (a) the angle of twist at B. (b) the angle of twist in A
Determine the smallest safe cross-sectional areas of members CD, Cl and CH for the truss shown. The allowable stress are 100 MPa in tension and 80 MPa in compression. Indicate tension or compression. (Draw the required FBD and answer in mm2). Fa a –– a→– a- B D |E A a F G H а 3 2 т 45 kN
Determine the force in members DF, DG, and EG of the roof truss, and state if the members are in tension or compression. The support at A is a pin and the support at L is a roller. You must include a FBD. 1 kN 1 kN 1 kN 1 kN 1 kNI D h = 8 m В OL E G K 2 kN 4 kN 5 kN 6 panels @5 m = 30 m-