Problem 1: A shallow foundation 25m × 18 m carries a uniform pressure of 175 kPa. Determine the vertical stress at two points that are 12 m and 24 m below the mid-point of one of the long sides, respectively. (a) using influencing factors (b) by means of Newmark's chart (c) using the 2:1 method (c) Comment on the results of the 2:1 method by comparing with those of the other two methods.

Problem 1: A shallow foundation 25m × 18 m carries a uniform pressure of 175 kPa. Determine the vertical stress at two points that are 12 m and 24 m below the mid-point of one of the long sides, respectively. (a) using influencing factors (b) by means of Newmark's chart (c) using the 2:1 method (c) Comment on the results of the 2:1 method by comparing with those of the other two methods.

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter9: Settlement Of Shallow Foundations

Section: Chapter Questions

Problem 9.17P

See similar textbooks

Similar questions

Solve Problem 7.8 using Eq. (7.29). Ignore the post-construction settlement. 7.8 Solve Problem 7.4 with Eq. (7.20). Ignore the correction factor for creep. For the unit weight of soil, use γ = 115 lb/ft3. 7.4 Figure 7.3 shows a foundation of 10 ft × 6.25 ft resting on a sand deposit. The net load per unit area at the level of the foundation, qo, is 3000 lb/ft2. For the sand, μs = 0.3, Es = 3200 lb/in.2, Df = 2.5 ft, and H = 32 ft. Assume that the foundation is rigid and determine the elastic settlement the foundation would undergo. Use Eqs. (7.4) and (7.12).
help me
From the given soil element, determine the major principal stress, in kPa, using the Pole Method. 150 kPa A 60 kPa 45⁰ 90 kPa 60 kPa B
A rectangular foundation 4 m x 6 m (Figure 1) transmits a stress of 100 kPa on the surface of a soil deposit. Plot the distribution of increases of vertical stresses with depth under points A, B, and C up to a depth of 20 m. At what depth is the increase in vertical stress below A less than 10% of the surface stress? Can I get a detailed explanation to the solution of this question? Including the finding of as and the graphs and finding the surface stress, load and increase in stress using the oz=4qsI method
In the figure, the rectangular foundation is loaded with a uniform load of 225 kPa. Accordingly, calculate the vertical stress increase 10 m below point A.
Two foundations are located next to each other as follows. Determine the stress increase on a horizontal plane (i.e. - the increase in vertical stress) beneath Point A at a depth of 3 m below the ground surface. The foundations are bearing on the ground surface. 3 m- +2.5 m -6 m 5 m A O= 90 kPa = 120 kPa 6 m
The plan of a foundation of uniform thickness for a building is shown in Figure below. Determine the vertical stress increase at a depth of 4 m below the centroid (solve by using Newmark influence chart). The foundation applies a vertical stress of 200 kPa on the soil surface.
A rectangular footing is uniformly loaded with q = 75 kN/m? as shown in the figure. Compute the vertical stress increments under Points A, B, and C at z = 5 m. 15 m 3.5 m A 1.87 m 8 m B Footing (Plane view)
Problem (4.10): The foundation plan shown in the figure below is subjected to a uniform contact pressure of 40 kN/m². Determine the vertical stress increment due to the foundation load at (5m) depth below the point (x). →|1.5m + 1.5m 2m 3 0.5m 2m + 3m 3m 3m
A rectangular foundation 6m x 12m carries a uniform pressure of 150 kN/m2 near the surface of a soil mass. Determine the vertical stresses at a depth of 6m below point A: 12 m 4 m 6 m 2 m A Select one: a. 0.040 b. 0.043 c. 0.0427 d. 0.044
The following results were obtained from CU tests on a clay soil that is the foundation material for an embankment. σ, (kPa) 300 400 600 0₁-0₂ (kPa) 331 420 487 Au (kPa) 111 160 322 (a) Determine the total and effective principal stresses for all three tests (You may summarize them in a table). (b) Recommend the shear strength parameters to be used for short-term and long-term analyses. The maximum confining pressure (cell pressure) at the depth of interest is 300 kPa. (Note: the clay is a normally consolidated one).
Help me please