Pls I need a complete solution ✅ using Bond Stress development length hook and splicing of reinforced In RCD. THANK U... -28mmØ top bar uncoated with fy = 276 MPa andconcrete compressive strength f = 28 MPa. Assume side, top and bottom cover to be greater than60mm. Using NSCP 2015, determine the following:PROBLEM 10.1:A concrete cantilever beam is reinforced with 6a.The required development length if the bars are straight using NSCP Table 425.4.2.4.Ans: La = 645.779mmAns: Lah = 250.164mmAns: Lah= 250.164mmb.The required development length if a 180° hook is used.C. The required development length if a 90° hook is used.

Answered: Image /qna-images/answer/670c2156-d31a-4043-bffe-df385c1d0e03.jpg

PROBLEM 10.1: A concrete cantilever beam is reinforced with 6- 28mmØ top bar uncoated with fy = 276 MPa and concrete compressive strength f = 28 MPa. Assume side, top and bottom cover to be greater than 60mm. Using NSCP 2015, determine the following: a. b. C. The required development length if the bars are straight using NSCP Table 425.4.2.4. Ans: La = 645.779mm Ans: Lah = 250.164mm Ans: Lah= 250.164mm The required development length if a 180° hook is used. The required development length if a 90° hook is used.

PROBLEM 10.1: A concrete cantilever beam is reinforced with 6- 28mmØ top bar uncoated with fy = 276 MPa and concrete compressive strength f = 28 MPa. Assume side, top and bottom cover to be greater than 60mm. Using NSCP 2015, determine the following: a. b. C. The required development length if the bars are straight using NSCP Table 425.4.2.4. Ans: La = 645.779mm Ans: Lah = 250.164mm Ans: Lah= 250.164mm The required development length if a 180° hook is used. The required development length if a 90° hook is used.

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter12: Composite Materials

Section: Chapter Questions

Problem 12.7P: Estimate the transverse tensile strength of the concrete in Problem 12.6.

See similar textbooks

Similar questions

Please double check your final answer. Subject - reinforced concrete A simply supported rectangular beam has a width of 300mm and the distance to the centroid of tension reinforcement is 330mm. The tension reinforcement has an area of 2463mm.2 and the area of compression reinforcement placed 70mm from the compression face of the beam is 1231.5mm.2, fy = 415MPa, fc'=30MPa, balanced steel ratio of 0.031.The design strength using 0.90 as the reduction faction is Choices A. 282kN.m B. 245kN.m C. 254kN.m D. 228kN.m
A symmetrical cross-section of a reinforced concrete shown has a value of f'c = 26.27 MPa and fy = 414 MPa. Calculate the nominal capacity based on the maximum steel area for a tension- controlled condition. Use the following dimensions: b = 498 mm d = 709 mm t = 152 mm web thickness - 152 mm b 1 I d
Problem Solving: A rectangular beam has dimensions of 250 mm by 625 mm with an effective depth (distance from extreme fiber in tension to the centroid of the reinforcing bars) of 575 mm and is reinforced with three 25 mmp. The concrete cylinder strength f.' = 27.6 MPa and the tensile strength in bending (modulus of rupture) is 3.28 MPa. The yield point of the steel is 414.7 MPa. The beam carries a bending moment of 61 kN.m. E_ = 200000 MPa. E_ = 4700,f. Using the transformed area method, determine the stress in the extreme fiber in compression.
Determine the required tension steel area of the T beam with given properties below. Width of flange bf = 500 mm Width of web bw = 340mm Thickness of flange tf = 140 mm Effective depth d = 350 mm Effective concrete covering d' = 75 mm Compressive strength of concrete fc' = 34.5 MPa Yield stress of steel bar fy = 375 MPa Mu = 415 kN-m As = mm2
CASE:A rectangular beam has the dimensions (see Fig.1) b = 15 in.,h = 30 in., and d = 27.37 in. and is reinforced with three No.9 bars. The concrete compressive strength fc' is 4000 psi, and the tensile strength in bending (modulus of rupture) is 475 psi. The yield point of the steel fy is 60,000 psi, the stress-strain curves of the materials being those of Fig.2. Determine the stresses caused by a bending moment M = 45 ft-kips.Question1:Check this case, would the concrete of the beam crack? Please calculate the strengths of those two materials in this beam.Question2:Suppose the beam under this case is subject to a bending moment M = 110 ft-kips (rather than45ft-kips as previously). Calculate the relevant properties and stresses.Question3:Determine the nominal moment Mn at which the beam of this case will fail. Question4:Have a comparison of the calculation results with those of three questions.
A rectangular beam has the dimensions (see Figure) b = 12 in, h= 20 in, and d= 17 in. and is reinforced with three No. 9 (No. 29) bars so that As - 3.00 in?. The concrete compressive strength fe is 4000 psi, and the tensile strength in bending (modulus of rupture) is 475 psi. The yield point of the steel f, is 60,000 psi. Determine the stress in the steel caused by a bending moment M = 10 ft-kips. 9 - 6.78 in, I- 4067 in, Es = 29000000, E - 3600000 L17 in. 20 in. 3 #9 bars (A, - 3.00 in.) 3 in. -12 in.- Select one: a. 2525 psi b. 2412 psi C. 2615 psi d. 2817 psi
A simply supported beam is reinforced with 4-ø28 mm at the bottom and 2-ø20 mm at the top of the beam, Concrete covering to centroid of reinforcement is 70 mm at the top and 64 mm at the bottom of the beam. The beam has a gross depth of 450 mm and gross width of 300 mm. fc'=28 MPa, fy=415 MPa. Assume bars laid out in single layer. Calculate the following if the limitin tensile steel strains is 0.004 for a ductile failure: Depth of the neutral axis from the extreme concrete compression fiber to the nearest whole number = _____________mm Design strength of the beam section to the nearest whole number =____________ kN-m Maximum service uniform live load over the entire span in addition to a DL = 20 kN/m (including the weight of the beam) if it has a span of 6 m = _____________ kN/m (to the nearest whole number)
The width and depth of a reinforced rectangular concrete beam is 400 mm and 700 mm, respectively. The effective depth is 630 mm. The material strengths are f'c=27.6 MPa and fy=414 MPa.Determine the amount of steel reinforcement at balanced condition in mm2.
Problem 1: A singly reinforced rectangular beam has a dimension b = 310mm and d = 410 mm. Factored moment is equal to 300 kN-m, Concrete compressive strength is 24 MPa, Steel yield strength is 276 MPa and the reduction factor is 0.9. Determine the required steel area in mm². Show the graph.
O Find the ultimate moment of resistance for the rectangular section reinforced as shown below. material strengths: Concrete Reinforcement Width of section Reinforcement fcu:= 30-MPa fy:= 450-MPa b:= 280-mm d:= 510-mm A, 2410-mm d':= 50-mm A's:= 628-mm² b A', d'
Determine the required tension steel area of the T beam with given properties below. Width of flange bf = 500 mm Width of web bw = 340 mm Thickness of flange tf = 140 mm Effective depth d = 350mm Effective concretee covering d' = 75mm Compressive strength of concrete fc' = 34.5 MPa Yield stress of steel bar fy = 375 MPa Mu = 415 kN-m As = _________ mm2
The width and depth of a reinforced rectangular concrete beam is 400 mm and 700 mm, respectively. The effective depth is 630 mm. The material strengths are f'c=27.6 MPa and fy=414 MPa. Determine the amount of steel reinforcement in mm2 to achieve a steel train of 0.004. and the nominal flexural strength in kN.m corresponding to a steel ratio of 1.75%