Problem 12-9 A curved cantilever AB in the form of quadrant of a circle carries a load W at the free end B, as shown in Fig. 12.11. Find the vertical deflection of point C at π/4 location. B PE су AK VET 1801 π/4 R Fig. 12.11 F W G

Problem 12-9 A curved cantilever AB in the form of quadrant of a circle carries a load W at the free end B, as shown in Fig. 12.11. Find the vertical deflection of point C at π/4 location. B PE су AK VET 1801 π/4 R Fig. 12.11 F W G

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter10: Statically Indeterminate Beams

Section: Chapter Questions

Problem 10.5.3P: Solve t he preceding problem by integrating the differential equation of the deflection curve.

See similar textbooks

Related questions

Q: 3. What are the characteristics of the different welding rods use in oxy-acetylene welding? Please…

A: given; what are the characteristics of the different welding rods use in oxy-acetylene welding?…

Q: WRITE THE ANSWER, SOLVE IT CLEARLY

A: Acceleration, a=Wma=-gro2r2=dvdta=dvdr×drdta=dvdr×vvdv=adrvdv=-gro2r2drIntegrate…

Q: QUESTION 7 A pump discharges water at 4 m³/s through a pipe. If the pressure difference between the…

A: FOLLOWING IS THE SOLUTION

Q: Crude oil, cp = 1.9 kJ/(kg.K), flows at a rate of 0.32 kg/s through the inner pipe of a tube-in-tube…

Q: (1) why the flow faster at the pipe center when you observe few millimeters from the pipe inlet; (2)…

Q: 3. A man is trying to pull the sled by applying a force of 500 N, as shown. The weight of the stone…

Q: 13. For Problems 1 to 3. Three forces were applied to the horizontal beam of negligible mass, as…

Q: Find the natural frequencies and corresponding modeshapes for the system shown below where m₁ = 2…

A: For solution refer below images.

Q: Find and solve at least 10 problems (5 easy and 5 hard) for Work and Energy

A: Given Work and energy To find 10 problems

Q: Magnitude of Vectors in 3D Let a =(2, -4, 6). Find a.

A: Given, Vector a → = < 2 , -4 , 6 > From the vector, x-component of vector = ax = 2…

Q: 1. Using the phase diagram for compound X on the right, answer the following questions. Liquid B 285…

A: Given data The given phage diagram of compound X…

Q: A UHart Dynamics experiment consists of collar B (mg = 10 kg) traveling to the left at vB = 1.5 m/s…

Q: Determine the discaharge Area of channel=22 m2 Flow velcoity=2.22 m/s

Q: A cylinder (diameter 4 m) of weight 50 kN is placed on the bottom of the tank as shown and oil and…

Q: A circular aluminum alloy [E = 70 GPa; α = 22.5 × 10–6/°C; ν = 0.33] pipe has an outside diameter of…

Q: The minimum factor of safety i able load P that may be applied

A: A=1.25in2yield strengthSyt = 46ksidiameterd=0.3inUltimate shear strengthSus=76ksiFOS=1.8a=53in…

Q: the net heat input per unit length of the weld.

A: Given data; Find net heat input per unit length of the weld ? Where, current=120 A voltage=10 V…

Q: 11" D calcresource.com 8" 4 3 4

A: following is the solution

Q: Find hydraulic radius Wetted area=5 m2 Wetted perimeter-7 m

A: Given data : Wetted area=A Wetted perimeter=P Required : Hydraulic radius

Q: A diesel engine driving an alternator at 95kg/hr of fuel at maximum load. The calorific value of the…

A: Given:m=95 Kg/hrCV=42.3*103 KJ/Kgηd=0.6ηa=0.85t=12 hrsρ=960 kg/m3

Q: Discussion: 1. The effect of distance between blocks on the balance force.

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for…

Q: Compound axial member ABC has a uniform diameter of d = 2.9 in. Segment (1) is an aluminum [E₁ =…

A: INTRODUCTION: A composite bar is constructed of two bars of different materials that are firmly…

Q: A dimensional analysis is performed on the drag on a boat. When the effects of viscosity can be…

Q: Q6. A small size cooling tower is designed to cool 400kg of water per minute. The water enters the…

Q: 4-A rigid tank is divided into two compartments by a partition. One compartment contains 3 kmol of…

Q: Q. A house wall may be approximated as two 1.2 cm layers of fiber insulating board, an 8.0 cm layer…

Q: An aluminum [E-9600 ksi] control rod with a circular cross section must not stretch more than 0.34…

Q: The coefficient of friction is 0.25 under each body in the system shown. If the body start from…

Q: Fnd the Face others = 22-5 N/mm Area = 3mm² 2

A: Given data : Area=A Stress=σ To find : Force

Q: Find the relation between backwards finite difference and average operator.

Q: the net heat input per unit length of the weld.

A: Given data; A gas tungsten arc welding operation is performed using following data; Arc…

Q: 11. Determine the magnitude of the reaction force at the roller support A when 0= 45°, as shown, to…

Q: A nozzle receives 36 kg/s of air at a speed of 142 m/s and with an enthalpy of 1060.00 kJ/kg. Air…

A: The exit velocity from the nozzle is (a) V = 824.72 m/s. (b) V = 842.71 m/s.

Q: A potential flow model of flow over a circular cylinder is described by the following velocity…

A: Write the expression of velocity potential. ϕ=U∞cosθr+R2r2 Calculate the velocity components.…

Q: (1) why the flow faster at the pipe center when you observe few millimeters from the pipe inlet; (2)…

A: INTRODUCTION: Whether the flow is laminar or turbulent determines the form of the velocity profile…

Q: What is the name of the flow when Mach number is one? A. Sonic flow B. Subsonic flow C. Supersonic…

A: Ratio of inertia force upon elastic force gives the value of mach number Mach number is denoted by M…

Q: 4/14 Determine the force in each member of the loaded truss. All triangles are equilateral. 8 kN с A…

Q: Is this for number 1 only?

Q: 1- An ideal gas mixture whose apparent molar mass is 36 kg/kmol consists of nitrogen N₂ and three…

Q: A wind tunnel is being used to study the aerodynamics of a full-scale model rocket that is 30 cm…

A: Given data Length of rocket = L = 30 cm = 0.3 m Maximum velocity of Rocket = 190 km/h

Q: A single ply of a certain graphite-epoxy composite with fiber oriented at 60° is in a planer state…

A: INTRODUCTION: The condition of stress is the highest resistance a body can provide against a load or…

Q: the net heat input per unit length of the weld.

A: Given data; Determine the net heat input per unit length of the weld ? Current,c= 450 A…

Q: Water flows at a rate of 0.035 m3/s in a horizontal pipe whose diameter is reduced from 15 cm to 8…

A: Given Diameter, D = 15 cm d = 8 cm Flow rate, Q = 0.035 m3/s Find Head loss, h

Q: 2. Is it important that base metal and filler rod have the same melting point or made of the same…

A: No, it is not important that base metal and filler rod have the same melting point or are made of…

Q: A tank with square bottom, 45 cm on a side rests on a horizontal surface with coefficient of static…

Q: ᴀ 14" x 12", ꜱɪɴɢʟᴇ ᴄʏʟɪɴᴅᴇʀ, ᴅᴏᴜʙʟᴇ-ᴀᴄᴛɪɴɢ ᴀɪʀ ᴄᴏᴍᴘʀᴇꜱꜱᴏʀ ᴡɪᴛʜ 6% ᴄʟᴇᴀʀᴀɴᴄᴇ ᴏᴘᴇʀᴀᴛᴇꜱ ᴀᴛ 12ʀᴘᴍ. ᴛʜᴇ…

A: Given data Clearance = 6% Suction Pressure = 14 psia Delivery Pressure = 42 psia N=1.25 We have to…

Q: final thickness that can be produced by this

A: Given data; Diameter=600 mmCoefficient of friction=0.05 Thickness=2 mmDetermine the minimum…

Q: 4.27 A 400-L tank, A (see Fig. P4.27) contains argon gas at 250 kPa, 30°C. Cylinder B, having a…

A: Write the given values with the suitable variables. P1=250 kPaP2=150 kPaV1=400 L=0.4 m3 Here, P1,…

Q: Q4. A hollow tube having an inside diameter of 2.5 cm and a wall thickness of 0.4 mm is exposed to…

A: Given: The diameter of the tube, d = 2.5 cm wall thickness, t = 0.4 mm The heat transfer…

Q: Find height P⋅E = 33.355 m = 3kg g = 10 m/s²

A: Given data : Potential energy=P.E Mass=m Acceleration due to gravity=g To find : Height

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

100%

Problem 12-9 A curved cantilever AB in the form of quadrant of
a circle carries a load W at the free end B, as shown in Fig. 12.11. Find
the vertical deflection of point C at π/4 location.
D
B
PE
vn
AK
/1
VET
100!!
π/4
R
Fig. 12.11
F
W
G

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Plot the load-deflection diagram for a pinned-end column with eccentric axial loads (see figure) if the eccentricity e of the load is 5 mm and the column has a length L = 3.6 m, moment of inertia L = 9,0 × 106 mm4, and modulus of elasticity E = 210 GPa. Note: Plot the axial load as ordinate and the deflection at the midpoint as abscissa.
An aluminum bar having a rectangular cross section (2.0 in. × 1.0 in.) and length L = 30 in. is compressed by axial loads that have a resultant P = 2800 lb acting at the midpoint of the long side of the cross section (sec figure). Assuming that the modulus of elasticity E is equal to 10 × 106 psi and that the ends of the bar are pinned, calculate the maximum deflection and the maximum bending moment Mmax.
1. Determine how much bar will deflect at various points aong its length. 2. Approximate the original problem as a five element system.
Problem 9 only, solve carefully, include the units in every step and draw the diagram. Thanks! A force tangent to 1 foot diameter pulley is 5 KN and is mounted on a 2 inches shaft. Determine the torsional deflectionif G = 83 x 106 Kpa
Question 1 Precision Engineering Contractors was awarded a government contract to construct a bridge joining two neighboring communities. The bridge ABC is simply supported at A and B 2 m apart and carries a uniformly distributed load of 50 KN/m between A and B, together with a concentrated load of 25 KN on an overhang at C, 0.5 m from B. Make a neat sketch of this bridge and calculate the maximum deflection from point A using Macaulay's Method. Take EI = 21 MNm²
A beam of uniform rectangular section 200 mm wide and 300 mm deep is simply supported at its ends. It carries a uniformly distributed load of 9 KN/m run over the entire span of 5 m. if the value of E for the beam material is 1 X 104 N/mm2 , find the slope at the supports and maximum deflection. Give me complete solution based on the given above. Again I need to ask the same question since you gave me a wrong answer before.
For the wire form shown, use Castigliano's method to determine the deflec- tion of point A in the y direction. Consider the effects of bending and torsion only. Use the straight beam formulation for the bending energy. The wire is steel with E 200 GPa, v = 0.29, and has a diameter of 5 mm. Before cation of the 200-N force the wire form is in the xz plane 100 mm. = appli- where the radius R is
The deflection at x = 3L/4 is Select one: -17WL 384EI O a. -513wL* 6144EI Ob -81 wL 6144EI -57WL 6144EI Cd.
A wooden beam 5 m long, simply supported at its ends and it is carrying a point load of 8 kN at its centre. The cross-section of the beam is 160 mm wide and 270 mm deep. If E for the beam is 70x109 N/m2, the deflection at the centre is
3. Calculate the slope and deflection at the 60-kNm couple on the structure shown in the accompanying illustration. Use: a. Moment Area Method, b. Conjugate Beam Method 4 kN/m Fixed Hinge 60 kNm 5 m -5 m 5 m -5m I=1.46 x 10° mm". E=200000MPa Activate Windows so to Settings to activate W ndows.
Solve for the moments and reactions at the fixed supports. You MUST use the slope deflection method.
11B. Using the slope deflection method, determine the end moments of the given frame. 75KN EI = 2.00 Problem 11B 6.0m 8.0m EI = 3.16 EI = 8.94 2.0m 4.0m 4.0m