Problem 16.3: The temperature of the solid 20mm diameter post CD is increased by 50°C. Determine the force developed in the post. Both the post and the beam are made of A-36 steel which has the properties listed below. The beam has moment of inertia 1-255-10 mm. E = 200GPa, v=0.32; a-12.10 / °C Assume that there is no temperature increase in the beam ABC. 1.5m B 2.5m D 3m

Problem 16.3: The temperature of the solid 20mm diameter post CD is increased by 50°C. Determine the force developed in the post. Both the post and the beam are made of A-36 steel which has the properties listed below. The beam has moment of inertia 1-255-10 mm. E = 200GPa, v=0.32; a-12.10 / °C Assume that there is no temperature increase in the beam ABC. 1.5m B 2.5m D 3m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Quizs- Replace the loading system by an equial ent resultant force and Couple moment acting at Point o. fi=l00 N Mc:75 Nm 0:3m 200 0-5 m 0.4m
The cantilever beam whose details are given in Figure, if E = 200 000 N/mm2. Answer all the questions .below 20 kN A 53.13° 20 mm 180 mm 20 mm 200 mm 100 1000 mm mm
1) DETERMINE TENSILE BENDING THE CROSS-SECTION BELOW. SOKN 20KN/m 3m THE MAXimum STRESSES OF THE B 30 кн/т Gm COMPRESSIVE Ано THE BEAM BEAM GIVEN 150MM SHOWIN 30mm 180mm 30mm
4-61. The distributed loading is supported by the three suspender bars. AB and EF are made of aluminum and CD is made of steel. If each bar has a cross-sectional area of 450 mm², determine the maximum intensity w of the distributed loading so that an allowable stress of ( allow)st = 180 MPa in the steel and (o allow ) al = 94 MPa in the aluminum is not exceeded. Est 70 GPa. Assume ACE is rigid. 200 GPa, E al = al |-- B 1.5 m + st [0) D U 1.5 m Prob. 4-61 al 10 F E W = 2 m
Question Bank - Friction The two homogeneous bars AB and BC are connected with a pin at B and placed between rough vertical walls. If the coefficient of static friction between each bar and the wall is 0.4, determine the largest angle 0 for which the assembly will remain at rest. 600 mm 6N 600 mm 8 N A. Technology Druen by fanoation Tips: 6N force and 8N force are acting vertically by gravity at the center of the material. Expose the forces acting between the bars and the wall (F and N) Check which interaction will first impend sliding - then expose if free body diagram from the internal hinge at B. e =? Answer in ° (1-2 Decimals are accepted)
STRENGTH OF MATERIALS A boiler is constructed of 9mm thick steel plates that are fastened together at their ends using a butt joint consisting of two 9mm cover plates and rivets having a diameter of 10mm and spaced 60mm apart as shown. If the stream pressure in the boiler is 1.38MPa, determine (a) the circumferential stress in the boiler's plate apart from the steam, (b) the circumferential stress in the outer cover plate along the rivet line a-a, and (c) the shear stress in the rivets. 60 mm 0.78 m
Aload Pissupported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 17400 ksi] rods, and a solid steel [E = 30600 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.79 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.52 in. Assume L1=39 in and L2=77 in. If all bars are unstressed before the load Pis applied, determine the normal stresses in bronze rods (1) and steel rod (2) after a load of P = 29 kips is applied. |(2) (1) L2 (1) B. Answers: i ksi. ksi.
Q2. Replace the loading acting on the beam with a single resultant force. Determine (a) the force magnitude, F. (b) the horizontal angle of the force, 0. (c) how far the force should be placed from point A on the beam, x. A 60° |--2 -2 m 450 N 4 m 300 N B -3 m 700 N 30° 3000 N·m
An 800 N-m couple is applied to the flywheel asshown. The coefficient of belt friction is 0.20. Theminimum force P required to prevent rotation of theflywheel is applied.a.) Which Tension is larger, TA or TB? Explain why.b.) What is the angle of contact in radians?c.) What is the value of the ratio TA/TB?
The thin plate ABCD of mass 8 kg is held in the position shown by the wire BH and two links AE and DF. Neglecting the mass of the links, determine immediately after wire BH has been cut (a) the acceleration of the plate, (b) the force in each link. H. E 150 mm 30% A B F 200 mm 30 D. IC 500 mm
The copper pipe has an outer diameter of 50mm and an inner diameter of 30mm, If it is fixed at A and three torques are applied to it as shown, solve the shear stress at section 2. A 200mm 250mm 300mm 30 N-m 20 N-m 80 N-m O 0.94MPA O 4.68MPA O 187MPA O 2.81MPA
Calculate the maximum intensity w of the uniform distributed load that can be applied on the beam without causing the compressive members of the supporting truss to buckle. The members of the truss are made from A-36-steel rods having a 60-mm diameter. Use FS. = 2 against buckling. Need accurate answer only