Problem 19.2 After failures occurred in several cast-iron bearing housings an engineering testing team used strain gage rosettes (future topic in this course) to determine operating stresses. Through testing they determined the point where failure initiated and measured strain at that location. They then calculated the stresses evidently present at that point to be gx = 0 MPa, Q=115 MPa, xx= 75 MPa. The material has been characterized by a uniaxial test that resulted in ult=170 MPa and cult=655 MPa. Use an appropriate failure theory to affirm the findings that this state of stress is very near the theoretical fracture capacity of the material.

Problem 19.2 After failures occurred in several cast-iron bearing housings an engineering testing team used strain gage rosettes (future topic in this course) to determine operating stresses. Through testing they determined the point where failure initiated and measured strain at that location. They then calculated the stresses evidently present at that point to be gx = 0 MPa, Q=115 MPa, xx= 75 MPa. The material has been characterized by a uniaxial test that resulted in ult=170 MPa and cult=655 MPa. Use an appropriate failure theory to affirm the findings that this state of stress is very near the theoretical fracture capacity of the material.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Example: Convert the change in length data in Table 3-2 to engineering stress and strain and plot a stress-strain curve Homework- help Table 3-2 The results of a tensile test of a 0.505 in. diameter aluminum alloy test bar, initial length (1o) = 2 in. Calculated LTO Load (Ib) Change in Length (in.) Stress (psi) Strain (in./in.) 0.000 1000 0.001 0.0005 4,993 14,978 24,963 34,948 37,445 39,442 39,941 39,691 37,944 3000 0.003 0.0015 5000 0.005 0.0025 7000 0.007 0.0035 7500 0.030 0.0150 7900 0.080 0.0400 8000 (maximum load) 0.120 0.0600 7950 0.160 0.0800 7600 (fracture) 0.205 0.1025
The proof stress of a material under tensile loading can be considered as can be considered as equivalent to the ultimate tensile strength for aluminium alloys being only applied to engineering steels during a tensile test the intercept on the stress stain curve for a given strain where a line draw is parallel to the elastic response line. the stress at yield for materials have no defined yield stress
A tension test was performed on a specimen having an original diameter of 12.5 mm and a gage length of 50mm. The data are listed in the table below: Complete the following: Plot the stress-strain curve. Label the y-axis every 50 MPa, and the x-axis every 0.05 mm/mm. Plot the linear portion of the stress-strain curve (first 5 points). Label the y-axis every 50 MPa, and the x-axis every 0.001 mm/mm. Determine the approximate Modulus of Elasticity Determine the approximate Ultimate Stress Determine the approximate Fracture Stress Determine the approximate Modulus of Resilience Determine the approximate Modulus of Toughness Other Requirements: Provide an example hand-written calculation showing how you calculated one point on the curve. Remember to properly label your plots and provide axis labels with units. Hand sketched plots will not be accepted. Use Excel or similar software.
To determine the nominal or engineering stress and strain experienced by a specimen of a material while it is subjected to a tension test, and to be able to read important values from a conventional stress-strain diagram obtained from the test. A tension test is being conducted on a steel-rod specimen with a gauge length of L0=50 mm and initial diameter of d0=13 mm. Data were collected to form the conventional stress-strain diagram as shown. From the diagram, f = 506 MPa , e = 689 MPa , g = 585 MPa , and h = 0.146 mm/mm . A) Assuming that the strain remains constant throughout the region between the gauge points, determine the nominal strain ε experienced by the rod if it is elongated to L = 53.0 mm . B) Assuming that the stress is constant over the cross-sectional area and if the tension force used is P = 16.0 kN , find the nominal stress experienced by the rod. C)Determine the force P needed to reach the ultimate stress in the steel-rod specimen.
The table below shows the deformation data that resulted from applying a pure tensile load to a brass alloy rod with an initial length of 30 mm and a diameter of 10 mm. This rod was subjected to necking and beyond necking deformation. The data at fracture is shown in the last row. Applied Load (N) Length (mm) Diameter (mm) 75,100 33.8 68, 250 34.9 50,200 35.7 6.7 Solve for the TRUE STRESS/ES and TRUE STRAINS. 8.3 7.8
Part A The stress-strain diagram for a steel alloy having an original diameter of 0.40 in. and a gage length of 9 in. is shown in the figure below. (Figure 1) Determine the modulus of elasticity for the material. Express your answer to three significant figures and include appropriate units. HA ? Eapprox = Value Units Submit Request Answer Figure < 1 of 1 Part B a (ksi) 80 Determine the load on the specimen that causes yielding. 70 Express your answer to three significant figures and include appropriate units. 60 50 40 HA 30 20 Py = Value Units 10 € (in./in.) 0.04 0,08 0.12 0,16 0,20 0,24 0,28 O 0.0005 0.001 0.0015 0.002 0.0025 0.0030.0035 Request Answer Submit
To determine the nominal or engineering stress and strain experienced by a specimen of a material while it is subjected to a tension test, and to be able to read important values from a conventional stress-strain diagram obtained from the test.A tension test is being conducted on a steel-rod specimen with a gauge length of L0=2 in and initial diameter of d0=0.5 in. Data were collected to form the conventional stress-strain diagram as shown. From the diagram, f = 73.0 ksi , e = 101.0 ksi g=83.0ksi, and h=0.15in/in Part A - Nominal or engineering strain in the rod Assuming that the strain remains constant throughout the region between the gauge points, determine the nominal strain ε experienced by the rod if it is elongated to L = 2.5 in . Express the nominal strain in inches per inch to three significant figures. Part B - Nominal or engineering stress in the specimen Assuming that the stress is constant over the cross-sectional area and if the tension force used is P = 8.0 kips ,…
diagram and determine approximately the modulus of elasticity, the yield stress, the ultimate stress, and the fracture 2.00 in. The data is listed in the table. Plot the stress-strain 8-1. A tension test was performed on a steel specimen n original diameter of 0.503 in. and gage length of PROBLEMS *84. origi the f having an for t and stress. Use a scale of 1 in. Dodraw the elastic region, using the same stress scale but a 20 ksi and 1 in. = 0.05 in./in. strain scale of 1 in.= 0.001 in./in. Load (kip) Elongation (in.) 0. 0. 0.0005 0.0015 1.50 4.60 8.00 11.00 0.0025 0.0035 0.0050 11.80 11.80 0.0080 0.0200 12.00 16.60 0.0400 0.1000 0.2800 20.00 21.50 19.50 18.50 0.4000 0.4600 Prob. 8-1
Tensile test specimens are extracted from the "X" and "y" directions of a rolled sheet of metal. "x" is the rolling direction, "y" is transverse to the rolling direction, and "z" is in the thickness direction. Both specimens were pulled to a longitudinal strain = 0.15 strain. For the sample in the x-direction, the width strain was measured to be ew= -0.0923 at that instant. For the sample in the y-direction, the width strain was measured to be gw=-0.1000 at that instant. The yield strength of the x-direction specimen was 50 kpsi and the yield strength of the y-direction specimen was 52 kpsi. Determine the strain ratio for the x direction tensile test specimen. Determine the strain ratio for the y-direction tensile test specimen. Determine the expected yield strength in the z-direction. Give your answer in units of kpsi (just the number). If the sheet is plastically deformed in equal biaxial tension (a, = 0, to the point where & = 0.15, calculate the strain, 6, that would be expected.
Determine the yield strength of a material required such that the component would not fail when subject to the following stresses sigma1 = 2 MPa and sigma 2= -15 MPa sigma 3 = 10 MPa). Use a yield criterion that assumes that yield failure will occur when the maximum shear stress in the complex system becomes equal to the limiting shear strength in a simple tensile test.
The fluctuating stresses listed in the table are found at a critical location of a component made of steel with Se = 40 ksi, Sy = 80 ksi, Sut = 110 ksi and f= 0.87. These stresses are applied on the part within 10 s. What is the accumulative damage of this part? What is the life of the part in hours if this stress pattern continues to repeat for the remained of the part's life? Use Goodman criterion and Miner's rule in your solution. Loading order |Omin o max |Number of cycles -20 30 -10 50 1 3. -30 30 1
A tensile test specimen of 1045 hot-rolled steel having a diameter of 0.505 in. and a gage length of 2.00 in. was tested to fracture. Stress and strain data obtained during the test are shown. Determine the ultimate strength. Stress (ksi) 60 50- 40- 30- 20 10- 0 0 0 Upper scale O 66 ksi 28 ksi O 72 ksi O 53 ksi O 62 ksi Lower scale. 0.025 0.050 0.075 0.100 0.125 0.150 0.175 0.002 0.004 0.006 0.008 0.010 0.012 0.014 Strain (in./in.)