Problem 2 An Air Force Research Lab engineer is asked to evaluate the maximum theoretical work that could be produced by the first stage turbine section of an experimental jet engine. Test stand measurements provide the following information: a. Entering air conditions: 1400 K, 8 bar b. Exiting air conditions: .8 bar Part 1: Since you don't have a mass flow rate measurement, what will be the units will you report maximum theoretical work in? Part 2: Write the first law equation for your control volume showing all terms. What assumptions will you make to simplify the equation. Part 3: Pin down the outlet state on a notional T-s diagram for air (just show the two isobars). Why did

Problem 2 An Air Force Research Lab engineer is asked to evaluate the maximum theoretical work that could be produced by the first stage turbine section of an experimental jet engine. Test stand measurements provide the following information: a. Entering air conditions: 1400 K, 8 bar b. Exiting air conditions: .8 bar Part 1: Since you don't have a mass flow rate measurement, what will be the units will you report maximum theoretical work in? Part 2: Write the first law equation for your control volume showing all terms. What assumptions will you make to simplify the equation. Part 3: Pin down the outlet state on a notional T-s diagram for air (just show the two isobars). Why did

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. A 4-stroke, 8-cylinder, petrol engine, has the following parameters at sea level; fue consumption = 0.75 Itr/min, engine speed = 50 r.p.s., Ap = 60 mm Hg, venturi diameter = 4 cm, atmospheric pressure = 1.03 kg/cm', C, 0.8, air and fuel densities are 1.15 kg/m' and 700 kg/m' respectively. Calculate: AF when the temperature decreases by 10%.
3. At a load of 43,000 KW in a steam turbine generating set, 3600 RPM, the following data appear in the log sheet. Steam flow -190 Metric Tons/hour Steam pressure - 8.93 MPaa Steam temperature - 535C Feed-water temperature - 230 C Fuel Flow: Bunker Oil -3.4 Metric Tons/hr HHV=10,000 Kcal/hr Local coal -18 Metric Tons/hr HHV = 5350 Kcal/hr Determine the overall boiler efficiency. h at 8.93 MPa and 535°C -3475.7 KJ/kg hf at 230°C-990.12 KJ/kg
Q1) A turbine model having the following specifications was made to predict the behaviour of the actual turbine: Pt = 15'8 HP H= 12 m N= 474 rpm, Model scale n = 10 Determine the speed of the actual turbine runner and its power developed if the overall efficiencies of the turbine and its model are equal. Find the type of turbine of which the model was made.
THERMODYNAMICS UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS/DIAGRAMS LEGIBLY. NO LONG EXPLANATION NEEDED. USE 3 DECIMAL PLACES. BOX THE FINAL ANSWER. A pump discharges into a semi spherical tank at the bottom and cylindrical on top with a radius of 2 meters, and a total tank height of 8 meters. The flow rate is 80 gallons per minute and fluid specific gravity= 1.1. Determine the following: A) flow rate in kg/sec and time it takes to fill the tank in hours. Flow Rate and Time
THERMODYNAMICS UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS/DIAGRAMS LEGIBLY. NO LONG EXPLANATION NEEDED. USE 3 DECIMAL PLACES. BOX THE FINAL ANSWER. A pump discharges into a semi spherical tank at the bottom and cylindrical on top with a radius of 2 meters, and a total tank height of 8 meters. The flow rate is 80 gallons per minute and fluid specific gravity= 1.1. Determine the following: A) flow rate in kg/sec and time it takes to fill the tank in hours. B) the weight in tons of the liquid if full tank local gravity is 32.1 ft/sec squared. C) volume of the tank in metric gallons. D.) how many drums will be needed to transfer all of the tank contents (tank being full) to the drums?
HANDWRITTEN AND FINAL ANSWER MUST BE IN ENGLISH UNITS. Show solution.ANSWER iii. Consider an ideal gas with the following characteristics: R = 115 ft-lbf/lbm-R Cp = 0.25 + 0.00035T (BTU/lbm-R) i. Solve for the value of k at 1250 R. ii. Refer to the table shown below: SEE IMAGE iii. Solve the following unknown parameters for Carnot cycle: Volume at end of isothermal compression Heat added and Heat rejected Wnet Efficiency Mean effective pressure iv. Solve the following unknown parameters for Otto Cycle Mass Pressure and Temperature ateach corner Heat added and Heat rejected Wnet Efficiency Mean effective pressure Percentage clearance v. Solve the following unknown parameters for Diesel Cycle with 6% cut-off. Compression ratio Percentage clearance Heat added and Heat rejected Wnet Efficiency Mean effective pressure
5. A four stroke gas engine develops 4.2 kW at 180 r.p.m. and at full load. Assuming the follow- ing data, calculate the relative efficiency based on indicated power and air-fuel ratio used. Volumetric efficiency = 87%, mechanical efficiency = 74%, clearance volume = 2100 cm³, swept volume = 9000 cm" fuel consumption = 5 m³/h, calorific value of fuel = 16750 kJ/m³ [Ans. 50.2%, 7.456: 1]
| As a mechanical engineering technician, you are asked by your building manager to investigate the performance of a steam turbine at the main university building. Criticaly compare how heat transfer efficiency will affect the lifetime of the turbine.
CTQ2 Assuming the clearance is negligible for a single stage compressor with the following data. Atmospheric pressure: 90 kPa Atmospheric temperature: 17 °C Delivery pressure: 7 bar Free air delivery flow rate: 0.2 m/min Take "n" as 1.3, Cp = 1.005 kJ/kg K, Cv = 0.718 kJ/kg K Answer the questions for ethuto test What is the delivery temperature of air for an isentropic compression process in Kelvin to 1 decimal place?
Problem 2. Fluid circulates steadily through four devices in a power plant as shown in the sketch. Mass flow rates and enthalpies per unit mass are tabulated for some of the states. Heat- and work-interaction råtes are tabulated for some of the devices. Complete the following tables: h State (kg/s) (J/kg) Device (W) (W) A D B 1 15 A. 150 2 13 30 3 25 C 3. 4. 5
Describe the T-s diagrams accordingly by filling in the blanks. Use the sets of words given below for the correct description. reheat/ closed Ideal / Actual / vapour /cycle /Carnot/ Rankine/ Brayton/Ericsson/Stirling/regenerative/ open/with/a Nino To C @ 4 2. 5. 6. a b с e T f 1 4 In a two-stage gas turbine plant, with reheating after the first stage TA 25 decreases the thermal efficiencies. increases the thermal efficiencies. does not affect thermal efficiencies. Decreases the work ratio. increases the work ratio. does not affect the work ratio. equal. unequal. 2 5 The ideal compressor work and turbine work in a jet-propulsion engine is a b 9in 2/ qout Wpump.in High-pressure turbine 3 Reheating 6 Wturb,out Low-pressure turbine с not related to each other. d unpredictable (a) By writing an energy balance on the heat exchanger of a binary vapour power cycle, obtain a relation for the exit enthalpy regarding the mass flow rates of two fluids in terms of the other enthalpies. Take the…
Q#01: Explain the following terms in your own words. Aerodynamics. Mach Number. Sub-Sonic. Angle of Attack. Thrust Chord Line. Drag Coefficient. Pitch Moment. Wind Tunnel. Skin Drag