PROBLEM 2.0 The working substance for a Carnot cycle is 9 Ib of air. The volume at the beginning of isothermal expansion is 10 cu ft and the pressure is 300 psia. The ratio of expansion during the addition of heat is 2 and the temperature of the cold body is 90°F. Find The heat added BTU. The heat rejected in BTU. The mean effective pressure in psi. The ratio of expansion during the isentropic process The overall ratio of compression.

PROBLEM 2.0 The working substance for a Carnot cycle is 9 Ib of air. The volume at the beginning of isothermal expansion is 10 cu ft and the pressure is 300 psia. The ratio of expansion during the addition of heat is 2 and the temperature of the cold body is 90°F. Find The heat added BTU. The heat rejected in BTU. The mean effective pressure in psi. The ratio of expansion during the isentropic process The overall ratio of compression.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. A water-tube boiler having a heating surface of 325.23 m² evaporates 6349.21 kg of water in an hour from a feed temperature of 66 °C. Boiler pressure is at 1.04 MPaa and the steam quality at the boiler outlet is 99 %. What percent of its rated Bo. Hp was the boiler developing?
A piston/cylinder arrangement initially contains air at 150 kPa, 400°C. The setup is allowed to cool to the ambient temperature of 20°C. a. Is the piston resting on the stops in the final state? What is the final pressure in the cylinder? b. What is the specific work done by the air during this process?
At the start of the compression process in the reciprocating compressor of refrigeration plant the refrigerant is at 1.5 bar, dry saturated. At the end of the compression process, which is according to a reversible polytropic law pv-C., The pressure is 6.5 bar. Using the properties of refrigerant given as table, interpolating where necessary, calculate. • The change of specific entropy during the • The degree of superheat of refrigerant after compression. process.
A 5 m3rigid tank has propane at 500 kPa, 700 K and connected by a valve to another tank of 0.7 m3with propane at 350 kPa, 600 K. The valve is opened and the two tanks come to a uniform state at 350 K. What is the final pressure?For propane R = 0.1886 kJ/kgK
One mol of an ideal gas is taken through The gas is subjected a three-step cyclic process. successively to an isothermal expansion at 600 K from 5 to 3 bar (path a to b), a constant-pressure cooling (b to c), and a constant-volume heating (c to a). All processes are reversible. Cy and Cp AH for each step and for the entire process. Draw the cycle on the PV diagram. Compile all results in a table, as follows: 21.686 J mol-K-1 =30 J mol-1K-1. Calculate Q, W, AU and %3D
Define the Reversible Isothermal Compression
The plant runs at 300r.p.m. and each cylinder has a volumetric The specific heat capacity of liquid ammonia = diagrams and showing all given and calculated values; QUESTION 3 1.5kJ/kgK Calculate: 4.2 the mass flow rate of refrigerant per second; 4.3 the refrigeration effect per second; 4.4 the power to drive the compressor if the mechanical efficiency is 80%.
0.2 m'af an ideal gas at 200 "K and 2 har is cumpressed at constant volume to 4 har by heat addition. Then it is compressed adiabatically to 8 har, finally it expands isothermally to the initial point.Assume ep= 14.3 kkg K and ev= 10.2 kIkg K. 1- Draw pv diagram of the cycle. 2. Find the heat added of the constant vuhume proces. 3. Find the work of the adiabatic proces 4 Find the heat rejected and work of the isothermal process.
What is the ideal mass flow rate for a refrigeration and cryogenic plant for oxygen production? Show solution if necessary and reference.
Steam is supplied to a two-stage turbine at 48 bar and 400 °C. It expands in the firstturbine until it is just dry saturated, then it is re-heated to 400 °C and expandedthroughthe second-stage turbine. The condenser pressure is 0.04 bar. Determine the specific work output of the system to 3 d.p? what is the specific entalphy in kJ/kg for state 2?
Steam enters the steam-generating unit at a pressure of 20 bar and dryness of 0.96 and leaves at the same pressure at a temperature of 350°C. Mass flow rate of steam is 5 kg/s. Find the percentage increase in volume (%) due to drying and superheating.
Hi I would appreciate any help with this thermo procatice problem 2 kg of air in a piston cylinder initially at P1=101 kPa, T1= 300 K undergoes a cycle made up of three processes: 1-2 Isothermal compression until the volume is (1/15) of its original value.2-3 Constant Pressure heating3-1 Isentropic Expansion back to the initial state Assume air is an ideal gas with constant specific heats with the following values: Cpo=1.027kJ/kgK; Cvo= 0.740 kJ/kgK; R=0.287 kJ/kgK; ɣ=1.388 Fill in the state and processes table below and show all work.