Problem 3: The flooring of a warehouse is made up of double-tee joists (DT) as shown. The joists are simply supported on a span of 7.5 m. and pre tensioned with one tendon in each stem with an initial force of 745 kN each, located at 75 mm above the bottom fiber, loss of stress at service load is 18%. Load imposed on the joists are: Dead load 2.3 kPa Live load = 6 kPa Properties of DT: A 200,000 mm² yt = 88 mm a = 2.4 m I 1880 x 106 mm4 yb 267 mm a=2.4 m N.A. 75 mm 192 mm 88 mm 267 mm a. Compute the stress at the bottom fibers of the DT at mid-span due to the initial pre stressing force alone. b. Compute the stress at the bottom fibers of the DT at mid-span due to the service loads and pre stress force. c. What additional super imposed load can the DT carry such that the resulting stress at the bottom fibers at mid- span is zero.

Problem 3: The flooring of a warehouse is made up of double-tee joists (DT) as shown. The joists are simply supported on a span of 7.5 m. and pre tensioned with one tendon in each stem with an initial force of 745 kN each, located at 75 mm above the bottom fiber, loss of stress at service load is 18%. Load imposed on the joists are: Dead load 2.3 kPa Live load = 6 kPa Properties of DT: A 200,000 mm² yt = 88 mm a = 2.4 m I 1880 x 106 mm4 yb 267 mm a=2.4 m N.A. 75 mm 192 mm 88 mm 267 mm a. Compute the stress at the bottom fibers of the DT at mid-span due to the initial pre stressing force alone. b. Compute the stress at the bottom fibers of the DT at mid-span due to the service loads and pre stress force. c. What additional super imposed load can the DT carry such that the resulting stress at the bottom fibers at mid- span is zero.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two pieces of lumber having square section (b x b) are arranged and supported as shown. The horizontal lumber is hinged at the left and free at right. The right end carries a concentrated load P. The vertical lumber supports the horizontal lumber at the midspan. Find the following: a) maximum shear stress, b) maximum bending stress, and c) maximum compressive stress. Hinge DATA FOR PROBLEM P L b (N ) (m ) (m m ) (m m ) 6 5040 1.47 140 140
1. The flooring of a warehouse is made up of double-tee joists (DT) as shown. The joists are simply supported on a span of 7.5 m. and pre tensioned with one tendon in each stem with an initial force of 745 kN each, located at 75 mm above the bottom fiber, loss of stress at service load is 18%. Load imposed on the joists are: Dead load = 2.3 kPa Live load = 6 kPa Properties of DT: A = 200,000 mm² yt = 88 mm a = 2.4 m I = 1880 x 106 mm4 yb = 267 mm a=2.4 m N.A. 75 mm 192 mm 88 mm 267 mm a. Compute the stress at the bottom fibers of the DT at mid-span due to the initial pre stressing force alone. b. Compute the stress at the bottom fibers of the DT at mid-span due to the service loads and pre stress force. c. What additional super imposed load can the DT carry such that the resulting stress at the bottom fibers at mid-span is zero.
Two pieces of lumber having square section (b x b) are arranged and supported as shown. The horizontal lumber is hinged at the left and free at right. The right end carries a concentrated load P. The vertical lumber supports the horizontal lumber at the midspan. Find the following: a) maximum shear stress, b) maximum bending stress, and c) maximum compressive stress. Hinge DATA FOR PROBLEM 1 P (N ) (m ) m m) (m m) L 6 504 5 1.38 14 4 14 4
The rectangular wood beam is loaded as shown in the figure. Determine the largest allowable magnitude of the load P if the working stresses are 10 MPa in bending and 1.2 MPa in shear. P 150mm 8 kN/m 2m 1m B C 250mm
Two pieces of lumber having square section (b x b) are arranged and supported as shown. The horizontal lumber is hinged at the left and free at right. The right end carries a concentrated load P. The vertical lumber supports the horizontal lumber at the midspan. Find the following: a) maximum shear stress, b) maximum bending stress, and c) maximum compressive stress. P Hinge DATA FOR PROBLEM 1 b b (N ) (m ) (m m ) (m m ) 6 5040 1.38 146 146
A compound girder consists of a 45 cm by 18 cm steel joist, of weight 1000 N/m, with a steel plate 25 cm by 3 cm welded to each flange. If the ends are simply-supported and the effective span is 10 m, what is the maximum uniformly distributed load which can be supported by the girder? What weld thicknesses are required to support this load? Allowable longitudinal stress in plates = 110 MN/m² Allowable shearing stress in welds = 60 MN/m² Allowable shearing stress in web of girder = 75 MN/m² 2.4cm -18cm 14cm 45cm
Problem Sets - 2: The rectangular wood beam is loaded as shown in the figure. Determine the largest allowable magnitude of the load P if the working stresses are 10 MPa in bending and 1.2 MPa in shear. P 150mm 8 kN/m 2m 1m B C 250mm
2. The manufactured wood beam carries the concentrated loads shown. What is the maximum safe value of P if the working stress in shear is 6 MPa? 20 mm 80 mm |3P 2 m 2 m 70 mm B 160 mm -- NA I = 15.52 × 106 mmª 1.0 m 1.0 m 20 mm
Problem A rolled steel joist of I section has the dimensions as shown in. This beam of I section carries a u.d.l. of 40 kN/m run on a span of 10 m, calculate the maximum stress produced due to bending. N -200 mm- 360 mm 10 mm 20 mm A 400 mm 20 mm
Problem 6: The wood beam is subjected to a load of 12 kN. Determine the transverse shear stress at point A is located 75 mm from the lower surface of the beam. Also what is the bending normal stress at A? 12 KN + 300 mm TH 200 mm -2 m---1 4.1 75 mol IM
A prestressed beam has a width of 300 mm and depth of 600 mm. It is subjected to a bonded prestress tendon having an area of 590 mm2 acting at a distance 550 mm from the compression, face of the member. fc' = 34.6 MPa, fpu = 1860 MPa, fpy = 0.85fpu (stress-relived strands). COMPUTE THE DEPTH OF THE COMPRESSION BLOCK (mm)
Topic: Restrained Beams 140KN 2.5m 3.5m 5KN/m 3.2m МА 6m MB 11WL2 Pab² 5WL2 Pa?b MA = - MB = - 192 L2 192 L2 INSTRUCTION: 1. Determine the maximum stress in the timber beam with the size of 120 x 370mm.