Problem 3. Lap connection is made of A325 % inch diameter bearing type bolts that threads are not in theplane of shear. The plates 3/8 x 7 and 5/16 x 7 are made of A36 (F,=58 ksi) steel. If live load to dead load ratiois 4, find the maximum service load that the connection can carry.A325X% in diameter boltsPL 3/8 x 7PL 5/16 x 71.5 in 2 in 2 in 1.5 in1.5 in2 in2 in1.5 in

Answer A 325 group bolt 3/4 inch diameter bolt Plate 38 x 7 Plate 516 x 7 A 36 steel Live loadDead…

Problem 3. Lap connection is made of A325 % inch diameter bearing type bolts that threads are not in the plane of shear. The plates 3/8 x 7 and 5/16 x 7 are made of A36 (Fu=58 ksi) steel. If live load to dead load ratio is 4, find the maximum service load that the connection can carry. A325X PL 3/8 x 7 % in diameter bolts P PL 5/16 x 7 1.5 in 2 in 2 in 1.5 in 1.5 in 2 in 2 in 1.5 in

Problem 3. Lap connection is made of A325 % inch diameter bearing type bolts that threads are not in the plane of shear. The plates 3/8 x 7 and 5/16 x 7 are made of A36 (Fu=58 ksi) steel. If live load to dead load ratio is 4, find the maximum service load that the connection can carry. A325X PL 3/8 x 7 % in diameter bolts P PL 5/16 x 7 1.5 in 2 in 2 in 1.5 in 1.5 in 2 in 2 in 1.5 in

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter3: Tension Members

Section: Chapter Questions

Problem 3.5.1P

See similar textbooks

Similar questions

The connection shown below uses 1-inch-diameter Group A bolts with the threads not in the shear plane. No slip is permitted. Both the tension member and the gusset plate are A36 steel. These bolts have not been added to distribute loads in the filler and two fillers are used. Use LRFD for solution. What is the design strength for block shear in kip? Express your answer in two decimal places. 1/2" thick Gusset Plate 3/8" thick 2" 3" 2" 2" 3" 3" 2"
Tension Member –Problem 1 12 - ¾" Bolts Gusset Plate Plate thickness t = ½" 2" Tension Member A36 Steel Plate 3" P, 10" 3" 2" Find the Capacity of this 4" 4" 4" tension member
Problem. A bolted connection shown consists of two plates 300 mm x 12 mm connected by 4 - 22 mm diameter bolts. 12 mm bolts T12 mm te12 mm P 300 75 75 75 Edge distances = 75 mm %3D dnole for tensile and rupture = dp +3 mm %3D dnole for bearing strength for Lec = d + 1.5 mm Fy = 248 MPa Fu = 400 MPa %3D En 330 MPa %3D Use LRFD design method. Determine the design strength due to tensile rupture strength of plates. (kN)
A) The 3/4 in x 15 in plate has 4 rows (or horizontal lines) of bolts. Each row has 3 bolts. The bolt diameter is 7/8 in. Determine the gross area (Ag) and the net area (An) 3/4 15 O O O O O O Q O O 3" 3 27 3 784 Bolts Pet *
The connection shown below uses 1-inch-diameter Group A bolts with the threads not in the shear plane. No slip is permitted. Both the tension member and the gusset plate are A36 steel. These bolts have not been added to distribute loads in the filler and two fillers are used. Use LRFD for solution. What is the design strength for block shear in kip? Express your answer in two decimal places. 2" 3" 2" 1/2" thick Gusset Plate O 2" 3" 3" 2" 3/8" thick P
Considering the following steel connection. The plates in Pink are 9mm steel plates. The middle plate (Yellow) is 18mm thick. The width of the plate is 100mm. The maximum allowable tension stresses on any of the plates is 100Mpa in Gross Area Yielding and 150 Mpa for Net Area or Tension Rupture. The bolts used are 8mm in diameter, the holes are 10mm in diameter, no need to add 1.6mm. The bolts allow a maximum of 280 Mpa of shear. Determine the maximum allowable "P" of the connection in kN.
The connection shown below uses 1-inch-diameter Group A bolts with the threads not in the shear plane. No slip is permitted. Both the tension member and the gusset plate are A36 steel. These bolts have not been added to distribute loads in the filler and two fillers are used. Use LRFD for solution. What is the design strength for tension on gross area in kip? Express your answer in two decimal places. 1/2" thick Gusset Plate 3/8" thick 2" 3" 2" 2" 3" 3" 2" P.
The butt connection shows 8-22 mm diameter bolts spaced as shown below. P- 50 100 50 50 100 50 16 mm +HHHH 40 80 40 12 mm Steel strength and stresses are: Yield strength, Fy = 248 MPa Ultimate strength, Fu = 400 MPa Allowable tensile stress on the gross area = 148 MPa Allowable tensile stress on the net area = 200 MPa Allowable shear stress on the net area = 120 MPa Allowable bolt shear stress, Fv = 120 MPa Based on the gross area of the plate. Based on the net area of the plate. Based on block shear strength. Bolt hole diameter = 25 mm Calculate the allowable tensile load, P, under the following conditions:
3. Determine Rn based on bolt limit states. Slip critical connection is used for design and Grade 10.9 M22 Bolts with Class A surface. Check minimum edge distance and spacing with TSSDC 2016. All members are $355. There is no filler between plates and Du=1.0. Fy= 355 MPa; Fu=510 MPa; E=200000 MPa. All units are in mm. $R.=? 100 100 O 60 Geset Plate 75 Plate Gusset Plate $R.=? *20*201 Plate
Determine the maximum factored LRFD tensile force capacity in tension only (no block shear). The angle is ASTM A36 steel. X = 0.7 Y = 3.8 Z=1/2 Round your answer to 2 decimal places. Your Answer: Incorrect The answer is 77.15 ± 1%. 1/2" X" bolts 1½" Gusset plate -L3 X 3 X Z Tu I
Two plates each with thickness t = 10 mm are bolted together with 6 - 16 mm diameter bolts forming a lap connection. Plate (A36): Fy = 248 Mpa FU = 400 MPa bolts are A325 in standard holes with threads excluded from shear planes. Considering Tension Yielding, compute the the design strength for LFRD. Use NSCP 2015 Round your answer to 2 decimal places.
A992 steel is used for the tension member shown. The bolts are ¾ inch in diameter. The connection is to a ⅜ inch thick gusset plate. A. Determine the nominal strength based on the gross area. B. Determine the nominal strength based on the effective net area.