Answered: Problem 4: For the gear system, find…

Problem 4: For the gear system, find the damping D to yield a 20% overshoot in output angular displacement for a step input in torque. T(1) 0,(1) N = 25 )1 kg-m² N2 = 5 N3 = 10 D N-m/rad N4 = 5

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1: (Section A) Considering single degree undamped vibration system and Newton's equation as follow: më +kx=0; find the solution of the displacement equation [(t)=Cietwnt+C2e-lwn] for the case with: Wn = 2 rad/s, x (0) = 1 mm, and x(0) = v5 mm/s. (Section B) Given the matrix equation of motion of a two degree-of-freedom system 3m 2k - k = 0 X2 + as: -k 4k m Determine (a) the natural frequencies, (b) the modes shapes.
The y-axis of an x-y positioning table is driven by a stepping motor that is connected to a leadscrew with a 3:1 gear reduction. The stepping motor has PPR-72 pulse/rev. The leadscrew has a pitch 0.2 in/rev and provides an axis range = 30 in. Determine (a) the required rotational speed of the y-axis stepping motor and (b) the corresponding pulse train frequency to drive the table in a straight line (incremental positioning) from point (20,25) inch to point (4.5,7.5) inch in exactly 30 sec (0.5min). Ignore acceleration.
Project 4: Gearbox and compound train gear system are widely used in power transmission systems to change input torques and rotational speed. Your task in a company that manufactures compound gear system box is to determine the necessary parameters to obtain a required output and securely mounting the gearbox. If the compound gearbox shown in Figure.5 has the following design specifications: B D F LOUTPUT INPUT Figure.5: Compound gear train system (left), Gearbox securely mounted by clamps (Right) Gear A has 20 teeth, Gear B has 150 teeth, Gear C has 40 teeth, Gear D 140 teeth, Gear E has 15 teeth and Gear F has 200 teeth. Input power and speed, respectively, 25 kW and 1600 rpm (clockwise). Your manger asked you the perform the following analysis steps: 1. Determine the velocity ratio/ gear ratio of compound gear system. 2. Calculate the output torque and determine its direction. 3. Find the required total/hold torque to securely mount the gearbox. 4. Explain the use of compound gear…
A NC machine tool table is powered by a servomotor, lead screw, and optical encoder. The lead screw has a pitch = 5.0 mm and is connected to the motor shaft with a gear ratio of 16:1 (16 turns of the motor for each turn of the lead screw). The optical encoder is connected directly to the lead screw and generates 200 pulses/rev of the lead screw. The table must move a distance = 100 mm at a feed rate = 500 mm/min. Determine (a) the pulse count received by the control system to verify that the table has moved exactly 100 mm; and (b) the pulse rate and (c) motor speed that correspond to the feed rate of 500 mm/min. Solve the problem assuming the optical encoder is directly coupled to the motor shaft rather than to the lead screw.
The drive unit for a positioning table is driven by a leadscrew directly coupled to the output shaft of a stepping motor. The pitch of the leadscrew = 0.18 in/rev. The table must have a linear speed = 35 in/min. If the relationship between leadscrew pitch p and number of step angles n, is as follows: ns-1250p/rg, determine (a) the minimum number of step angles (pulse/rev) in the stepping motor to achieve the required accuracy, (b) the associated step angle, and (c) the frequency of the pulse train required to drive the table at the desired speed.
(a) The position-time plot of a spring-mass-damper system is as shonn Find the damped frequency. Find the logarithmic decrement. Find the damping ratio. Spring Mass Damper 12 Time Position
QUESTION 3 For the rotational gear system shown in Figure Q3, a step torque is applied at 6(1). T(t) 010) 0 2(0) 1.07 kg-m2 1.53 N-m-s/rad 1.92 N-m/rad Figure Q3 Determine: 3.1- the transfer function G(s) =0.(s)/T(s); 3.2-the per cent overshoot, settling time and the peak time for 0.(1).
Problem 4 The compound gear train of a three stages reduction gear is use to transmit power from a power source to a drum with 1 meter in diameter, as shown in Figure P4. The power source generates 500 Nm torque at the speed of 500 rpm and can produce acceleration of 10 rad/s?. Assume there is no friction in the drum, mass of the cable is negligible and the cable is in-elastic. With this condition, determine the folbwing. i. ii. iii. Angular vebcity and acceleration of the drum. Power required to overcome the friction torque in the bearing. Power required to accelerate the inertia of the gear system. Load M that the drum can lft. N. [1.05 rad/s; 0.2 rad/s ; 1.13 kW ; 2.12 kW ; 3,221.7 kg] Drum2 (2) Drum 1 Power A source 凶凶 (1) Load, M (4) Figure P4 Given:- Number of gear teeth, t:- t;=40 ; t2=100 ; t;=40 ; t4=160 ts=40 ; t6=200 Equivalent mass moment of inertia, Ieq:- Ipower source=2 kgm ; Igear 23=10 kgm2 ; Igear 45=20 kgm2 ; Igear 6 & drum=40 kgm? Friction torque in bearing, F:-…
Gearbox and compound train gear system are widely used in power transmission systems to change input torques and rotational speed. Your task in a company that manufactures compound gear system box is to determine the necessary parameters to obtain a required output and securely mounting the gearbox. If the compound gearbox shown in Figure.5 has the following design specifications: B D 'F LOUTPUT INPUT E T2 Figure.5: Compound gear train system (left), Gearbox securely mounted by clamps (Right) Gear A has 20 teeth, Gear B has 150 teeth, Gear C has 40 teeth, Gear D 140 teeth, Gear E has 15 teeth and Gear F has 200 teeth. Input power and speed, respectively, 25 kW and 1600 rpm (clockwise). Your manger asked you the perform the following analysis steps: 1. Determine the velocity ratio/ gear ratio of compound gear system. 2. Calculate the output torque and determine its direction. 3. Find the required total/hold torque to securely mount the gearbox. 4. Explain the use of compound gear…
a) Engine-Pump mechanism in Figure 3.1 shows few gears meshing with different parameters . Based on the picture shown below. Given: n1 = 500 rpm; N1 = 20; N2 = 70; N3 = 18; N4 = 54 Compute : (i) value of n4 (i) Torque and power changes at Gear 4 n1, N1 n4, N4 Engine Pump n2, N2 n3, N3 Figure 3.1
Q6. Gear and Motor selection: For a 50 Hz supply frequency, the motor speed is 50 revolutions per second. What gearbox is required to step this down to 2 rad s−1 at the pulley wheel? What is the maximum torque to be developed by the motor? Round off your answers to one decimal place. -The gear ratio required is ? - The maximum torque to be developed by the motor is Nm ?
Consider a circular cam of eccentricity R/2 as shown in Figure Q1. The cam is pivoted at O and has a diameter of 32 mm. The position coordinate of the follower A is x and the angle is given by: R x(8) : cos e + vcos²0 + 3) V %3D Assume the cam rotates in the clockwise direction with an angular velocity of 2000 rev/min. At an angular displacement of 45° find the velocity of the follower.