COS (2T10Problem 4. A voltage wave of the form V+ = (2x 10-4V) cos(t-kz is incident from cable 1 with characteristicimpedance 201 = 1200 onto a connection to cable 2 with characteristic impedance Z02=1002. Take the speed of the cablewave in each cable to be 2 x 10 m/s.A) Find the amplitudes of the reflected and transmitted voltages.B) Find the incident, reflected, and transmitted powers.

Now calculating the Reflection Coefficient of the medium:We Know:Reflection Coeff.=> Now putting…

Problem 4. A voltage wave of the form V+=(2x 10-4V) cos( -k is incident from cable 1 with characteristic impedance Zo1 = 1202 onto a connection to cable 2 with characteristic impedance 202=1002. Take the speed of the cable wave in each cable to be 2 x 10³ m/s. 2=10% A) Find the amplitudes of the reflected and transmitted voltages. B) Find the incident, reflected, and transmitted powers.

Problem 4. A voltage wave of the form V+=(2x 10-4V) cos( -k is incident from cable 1 with characteristic impedance Zo1 = 1202 onto a connection to cable 2 with characteristic impedance 202=1002. Take the speed of the cable wave in each cable to be 2 x 10³ m/s. 2=10% A) Find the amplitudes of the reflected and transmitted voltages. B) Find the incident, reflected, and transmitted powers.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

In non-sinusoidal wave sources, the dissipated power in the load is depends on the value of . . Variable Current Average Current Constant Current All-of-them
The maximum value of standing wave voltage V (2) | is in phase with: Select one: a. the minimum value of the standing wave current I (z)|- O b. the maximum value of the standing wave current I (z) |.
3. Generate a square wave of 0.5Hz with a duty of 50% on pin P1.0 as XTAL = 12 MHz. U1 12DXINT PODADO P0.1/AD1 PO 2/AD2 18 XTAL2 PO.3/AD3 P0.4/AD4 34 PO.S/ADS PO.6/AD6 9 32 RST PO.7/AD7 P2.0IAS 21 P2.1/49 P22/A10 PSEN ALE P2 3/A11 P2.4/A12 P2.5/A13 P2.6/A14 25 26 EA 20 P2.7/A15 10 P1.0 2 P1.1 P12 P1.3 P3.ORXD P3 1/TXD11 P32TS 12 P3.3ANT113 P1.4 P1.5 P34/7014 P15/T1 P3.6WR 15 16 17 P1.6 P1.7 P3.7/RD 50651 4 4 I R1 0.01 R2 0.01k D2 LED-BIBY D1 ■ LED-BIBY 30 31 -2.1
Channel 1 and Channel 2 Time (ms) Phase problem. In the above figure the time base is 1 ms/div, what is the period of the signal from Channel 1 in ms? What is the phase difference (in degrees) between the signals in Channel 1 and Channel 2? ms, _degrees Voltage (arbitrary units)
Problem: Caleulate Average value, Rins value and Form faetor of the sawtooth wave show in the figure. WA
Please explain in detail. A. In a series circuit, if the AC voltage is measured across the AC voltage source, will there be any variations in the phase of the AC voltage across each resistor from the measured AC voltage across the source? B. In an AC voltage source, why does voltage vary with time? Please explain in detail. C. In a series circuit, are the frequencies of the AC voltages across each resistor the same? Why is this so? ...
In DC choppers the wave forms for input and output voltages are respectively a. both discontinuous b. discontinuous,continuous c. both continuous d. continuous,discontinuous
The ripple factor for pure dc is Answer:
Example 4 A lossles TL having Zo= 400 a borking at. 123m. By using Crank dragram, draw the standing wave at volta and current for 5m from the reciever end when. a) The Load ZR is short circuit and current equal to 1 Arms b) The load ZR is open circuit and the voltage equal to 400 Vin
With the same timebase of 250us what is the Frequency of the following wave?(?) Please solve with explaination as earlier..Thanks
For the pair of waveforms (input and output) captured in that picture, write the mathematicalexpression for Vout(t), using the phase of Vin(t) as the reference. Also, write the phasor expressions forVout and Vin. Vin = Yellow line Vout = Blue line Vin max = 2V Vout max = 440.0 mV phase = -78.7483
The following subquestions are multiple choice. They are about the frequency and amplitude of free-running triangular wave generators. Answer correctly and I'll upvote. Thank you.