Problem 5: The forked rod is supported by a collar at A, a thrust bearing at B, and a cable CD. Determine the tension within cable CD and the x, y, z components of reaction at supports A and B due to the loading shown. The supports at A and B are in proper alignment and exert only force reactions on the rod. 0.5 m A Im 0.5 m D Im 3 2 m F=1501 +401-80k) N

Problem 5: The forked rod is supported by a collar at A, a thrust bearing at B, and a cable CD. Determine the tension within cable CD and the x, y, z components of reaction at supports A and B due to the loading shown. The supports at A and B are in proper alignment and exert only force reactions on the rod. 0.5 m A Im 0.5 m D Im 3 2 m F=1501 +401-80k) N

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter4: Coplanar Equilibrium Analysis

Section: Chapter Questions

Problem 4.125P: The figure shows a three-pin arch. Determine the horizontal component of the pin reaction at A...

See similar textbooks

Similar questions

NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part Bar AD is attached at A and C to collars that can move freely on the rods shown. Consider a=0. B E 0.2 m-0.2m----0.2 m- P D Draw the free-body diagram needed to determine the tension in the cord and the reactions at A and C (You must provide an answer before moving on to the next part)
A 200 mm lever and a pulley of 240 mm diameter are welded to the axle BE which is supported by a thrust bearing at C and a journal bearing at D. A 720 N vertical force is applied at A when the lever is horizontal. Determine the tension T in the cord and the reactions at bearings C and D. You may assume that the bearings are properly aligned. You must include a free body diagram with your solution. 200 mm 720 N 80 mm 40 mm 120 mm Z 120 mm
Q.2) The windlass is supported by a thrust bearing at A and a smooth journal bearing at B, which are properly aligned on the shaft. Determine the magnitude of the vertical force P that must be applied to the handle to maintain the equilibrium of the 100kg bucket. Also, calculate the reactions at the bearings. Since the bearings at A and B are aligned correctly, only force reactions occur at these supports. 0.3 m 981 N 0.5 m 0.1 m By 0.4 m B 30% 0.3 cos 30°m X 0.3 m G 0.5 m 0.1 m 0.1 m X 100 kg 0.3 m 30% 0.3 m
Bar AD is attached at A and C to pinned collars that can move freely on the rods but don't restrain rotation. If the cord BE is at a 30° from vertical, determine the tension in the cord and the reactions at A and C. Answers: T=69.3 N, A=140 N, C=180 N 30° B a E 30° C -0.2 m-0.2 m 0.2 m- 80 N OD
X 3 m B 4 m N C E 800 N 4 m 600 N
Cables CE and BF along with the ball and socket at A support the rigid bar ABCD. (Due to the nature of this problem, do not use rounded intermediate values in your calculations-including answers submitted in WebAssign.) 3 m 2 m 4 m B F = -(750 N)k Determine the tension in each cable and the reaction components the ball and socket joint exerts on ABCD at A in newtons. (Indicate the direction with the sign of your answer.) BF = 2691 X N TCE = 1148 FAx = N Fav Faz =
The member is supported by a square rod which fits loosely through the smooth square hole of the attached collar at A and by a roller at B. The member is subjected to the forces Fi = 300 N, F2 = 450 N, and F3 = 600 N. (Figure 1) Determine the components of the reaction force of the support at A using scalar notation. Express your answers using three significant figures separated by comma. Ar, Ay = -300,-450 N Submit Previous Answers v Correct Part C Determine the components of moment of the reaction at A using scalar notation. Figure 1 of 1 Express your answers using three significant figures separated by commas. vec (MA)=: (MA)y, (MA): =- 900,100, – 1350 N.m B 1 m 2 m Submit Previous Answers Request Answer 2 m X Incorrect; Try Again; 4 attempts remaining < Return to Assignment Provide Feedback 圓

Determine the external reactions at A and F for the roof truss loaded as shown (positive answers are to the right and up). The vertical loads represent the effect of the supported roofing materials, while the 430-N force represents a wind load. 430 N y 290 N A Answers: Ax= = Ay = Fy= 60° i B Mi 480 N 60° 30⁰ 520 N G 9.5 m 550 N 30° 30° 280 N N Z Z Z N N F x
If the balloon is subjected to a net uplift force of F = 1000 N, determine the tension developed in ropes AB, AC and AD. (Note: This problem requires a Free Body Diagram and use of calculator or another tool of your choice to solve the system of equations.) 6 m 2 m -1.5 m -2 m 2.5 m B F A D
2.0 m 100 kg 2.0 m 0.5 m 1.5 m 1.5 m The pulley at E is frictionless. Point B is a pinned connection; support A is a fixed support. The pin at C is in a smooth slot. s in: Determine the magnitude of of the x-component of the reaction force at A, Ax= N. Determine the magnitude of of the y-component of the reaction force at A, Ay= N. Determine the magnitude of of the external moment applied at A, MA= Nm. O O :
PROBLEM 4 The strut shown is supported by a hinge at A and a cable at the right end. If the tension in the cable is 100N and the weight of the strut is 40N, determine the following. A 40° 31-33. Maximum weight of Block W. 34-36. Horizontal Reaction at Hinge A 37-39. Vertical Reaction at Hinge A. W| PROBLEM 5 The boom shown is 15m long weighs 150N and supported by a cable 6 meters above the hinge at point A. 40-42. Determine the Weight of Block W if the tension in the cable is 50N 43-45. Determine the force of the hinge on the boom A WI 30°
If the roller A is replaced by a pin, determine the corresponding reactions at A and then Identify the ff. (a) The bar which has the largest tensile force. What is the value? (b) The bar which has the largest compressive force. What is the value? 3m 2.7 kN 30 3m E 4.5 KN 3m 1.8 KN 30 3m Assume for all bars: A = 500 mm² and E = 200 kN/mm²