Problem V Given the truss below, take P₁= 40KN, P₂= 50KN, P₁-30KN, P₂=40kN, a=2m, h=1.5m. Use the Method of Joints to determine the forces in members EH, ED, DC, GH. Remember to specify whether they are in Tension or Compression. F a 21 R H ANA H a # h

Problem V Given the truss below, take P₁= 40KN, P₂= 50KN, P₁-30KN, P₂=40kN, a=2m, h=1.5m. Use the Method of Joints to determine the forces in members EH, ED, DC, GH. Remember to specify whether they are in Tension or Compression. F a 21 R H ANA H a # h

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Question 3 Which one of the following is not considered as the consolidation properties of soils?…

A: The soil has to handle the different types of loads. Some of these loads are applied for a short…

Q: What is the independent of irrelevant alternatives property of the logit model and how to overcome…

A: The Independent of Irrelevant Alternatives (IIA) property of the logit model is a key characteristic…

Q: On a map whose scale is 1in.=30ft, how far

Q: A reinforced concrete beam has the following properties bw=300mm d= 450mm f'c = 28Mpa fyt= 275MPa.…

A: bw=300mmd= 450mmf'c = 28Mpafyt= 275MPaFactored shear force at the critical section is 100 kN10mm…

Q: Water at T = 25°C is drawn from an underground detention tank and discharged into a drain using a…

Q: can you explain the steps for the SF and BM

Q: How to calculate trip generation using household income and car ownership

A: The objective of this question is to understand how to calculate trip generation using household…

Q: 3. Compute the maximum acceptable service load on an A36 steel plate tension member 1/4 in x 12in…

A: A36 steelPlate cross section = 1/4 in x 12 in25% Dead load ans 75% Live loadDiameter of the bolt =…

Q: Determine the moment of each of the three forces about point A. (MF1) A¹ (MF2) A¹ (MF3) A = -433…

Q: 1. Determine the moment of inertia about the horizontal centroidal x-x axis for the area shown in…

Q: The restaurant below has 4 booths (2 benches each), each bench is 54 inches in length and 8 fixed…

A: We need to find occupant load for the given small restaurant

Q: SHOW THE ILLUSTRATION/DIAGRAM AND COMPLETE SOLUTION. 2. Two tangents intersects at an angle of…

Q: ou are working on a concrete mix design that requires each cubic meter of concrete to have 0.40…

A: Given that; w/c ratio=0.45Mass of cement=335 kg/m3 ,Gcement=3.15Air content=4%Mass of dry…

Q: The structural engineering design section within the engineering department of a regional electrical…

Q: 7-18. Determine the slope at D and the displacement at the end A of the beam. El is constant. Use…

Q: Please show your complete solution. Thank you! In cantilever truss shown, compute the force in…

Q: 2. For the shown truss, determine the force in members BC, BH, and HC State whether the member is in…

A: Determine the force in members BC, BH and HC of the truss. Let's solve using method of section.

Q: A RA 62 w = 4 k/ft 10' 5' 50 in 50 5' B RB 78

Q: A gravity settling collector is to be used to remove particulate matter having a diameter of 100…

Q: Q3- Correct the following traverse and compute station coordinates: station A (x-1000m,b=1000m) AB B…

Q: Determine the shear and moment of the beam as a function of "x".

Q: A foundation measures 10 ft x 12 ft x 15 ft. Find the number of sacks of cement needed for 1:2:4…

A: Given that:Size of foundation: 10 ft x 12 ft x 15 ftConcrete mixture: 1:2:4

Q: Assuming the data follows a Normal distribution, what is the probability that the discharge is…

Q: Problem 2 The table shows reported accidents for a 10-mile highway section of the Diosdado Macapagal…

Q: in the process of solving the series

Q: The welded girder shown in the accompanying illustration h an external shear Vp = 300 k and V₁ = 350…

Q: What is the minimum size septic tank for an apartment building with 12 one-bedroom units, 4…

A: An apartment building with following details:12 one-bedroom units,4 two-bedroom units, and 2…

Q: Consider the beam in the given figure. Given: P= 13 kips and Elis constant. NOTE: This is a…

Q: The figure below shows a 20 m thick layer of normally consolidated clay (ϒt = 18.6 kN/m3) that is…

Q: Problem #1: Determine the moment of inertia of the composite area about the y-axis and the the…

Q: Which of the following is not an advantage of precast construction? Question 4 options: the…

A: Precast construction

Q: Example 3: Calculate the moment of the 250 N force on the handle of the monkey wrench about the…

A: Given data - F = 250 N Find out - Moment of the force on handle about the centre of the bolt .

Q: g) in what areas would the stirrups not be needed

A: A beam is given, we need to find out the location where stirrups not required

Q: Q2/ Calculate the strain of rod BC. A = 300 mm² and E= 200 GPa. Als B 30° 4300 P=20 KN L=3m L=2m St

A: The figure is shown in the above figure. Point load P = 20 kN A = 300 mm2 E= 200 GPa = 200 x 103 MPa…

Q: 9-14. Determine the reactions at the supports, then draw the moment diagram for each member. EI is…

Q: *9-60. Locate the centroid (x, y) of the composite area. 150 mm 100 mm -300mm

A: The centroid () of the composite area =?

Q: Please recheck Ra and Rb is actually equal to 6kn and not 15kn

A: As per the given question, we have to check the reactions at supports. Original question was: A beam…

Q: A wood with an sg=0.0233 has length and width equal to 1m. A man 60kg places the wood at a pool. a)…

Q: how do i solve the attached problem

A: The objective of the question is to determine the reactions at support A and the forces in all…

Q: A 20 m long concrete pile with a rectangular cross section of 460 mm × 460 mm fully embedded in sand…

A: Already some formulae given , Here for terzaghi equation, a few more are needed1) for loose sand , K…

Q: Q1: The following time distribution of the rainfall, estimate the -Index and W- Index of the…

A: As the value lies between 0.5 and 0.6 the assumption is correct

Q: In a certain situation, waste water having dissolved oxygen of 2.36 mg/lt is discharged at 1.25…

Q: A beam is loaded as shown in the diagram. Draw the S.F. and B.M. diagrams and find: (i) maximum S.F.…

Q: Determine the internal normal force, shear force, and moment at point C of the beam.

Q: Consider the beam given in the figure. Given: X=0.3 in, E=30,000 kips/in², and/= 240 in 4. NOTE:…

A: E = 30000 kip/in.2 I = 240 in.4 Determine the support reaction and draw the shear force and moment…

Q: What are the two, independent design criteria that all foundations (shallow and deep) must satisfy?…

A: Settlement is the main factor in designing the shallow and deep foundations. Because, if the…

Q: The storage-outflow characteristics for a reservoir are given below. Determine the storage-outflow…

Q: Draw the shear and moment diagram for the simply supported beam using Area Method. 100kN m 4m 25kN/m…

Q: A gravity settling collector is to be used to remove particulate matter having a diameter of 100…

Q: Design beams. Where fc' = 35 Mpa, fy = 420 Mpa. and bar 25 mm. L.L = 38 kN/m 7.5 m- 500 mm 350 mm

A: fc' = 35 Mpa fy = 420 Mpa Diameter of bar = 25 mmWe have to design a beam.As there is no specific…

Question

how do i solve the attached civil engineering problem

Problem V
Given the truss below, take P₁= 40KN, P₂= 50KN, P₁-30KN, P₂=40KN, a=2m, h=1.5m. Use the
Method of Joints to determine the forces in members EH, ED, DC, GH. Remember to specify
whether they are in Tension or Compression.
F
a
21
R
H
ANA
H
a
#
h

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Mention the given Data

VIEW

Step 2: Calculation of reaction and force in member

VIEW

Step 3: Calculation of force in member

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 4 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the forces in member BE of the Howe roof truss shown in lbs. P1 = 364 kN and P2 = 646 kN. Write numerical value and in 2 decimal places.
Given the loaded truss below, calculate the stresses in members CE, DE, and DF. The cross-sectional area of each member is 1.8 in^2. Indicate if it is tensile stress (T) or compression (C)
Consider the truss shown in (Figure 1). Suppose that F = 9.5 kN. Determine the force in member BC, CH, GH, and CG of the truss and state if the member is in tension or compression. (Hand written and clean writing please )
Determine forces in members JK, KD, and DE and state whether in compression or tension Ax=0 Ay=6 kip up Gy=6kip up
A mansard roof truss is loaded as shown. determine the forces in each members in kN. P=9.9 kN and x=4.1 m. Show solution, Free body diagrams and determine each member it is in tension or compression.
Evaluate the given Fink Truss using method of sections. Answer the following questions if ϴ = 30°, Ф = 60°, and the distance, d = 12 ft. What is the reaction at A? What is the force at in member BD? What is the force at in member FE? What is the force in member CE?
Usinf the method of sections, determine the force members GF, GD, and GC
Determine the force in member EG, and indicate whether the members are in tension or compression. if P=11kN. 24.75kN (T) 24.75kN (C) 39.66kN (T) 39.66kN (C) 41.25kN (T) 8.25kN (C) 8.25kN (T) 41.25kN (C) ORONORCORORORORC
Compute for forces in members CD and DF. Determine whether they are in tension or compression.
Situation 2: For truss shown, use method of joints. P= 5 kN. A)What is the force in member DE?* B)What is the force in member BC?
Refer to the truss shown a. Determine the maximum positive ordinate for member DC. b. Determine the location of a point load that will give the maximum compressive force for member AB. show solution asap ,answers in 4 decimal places
Given the Truss as shown below with θ = 45°. Using Method of Joints, determine the forces at the members AB, AD, AE, BC, BE, BF, CF, DE, EF, and FG.