Problem2:. Consider the circuits shown below. (a) Write the equation for current using the junction rule. (b) Write two equations using loop rule (c) Use these equations to find I₁, I2, and 13? (b) What is the power dissipated across each resistor (I²R)? V₁ = 24 V 12 R₂=652 R₁ = 802 ¹2 13 R3=452 W =₂=10 V

Problem2:. Consider the circuits shown below. (a) Write the equation for current using the junction rule. (b) Write two equations using loop rule (c) Use these equations to find I₁, I2, and 13? (b) What is the power dissipated across each resistor (I²R)? V₁ = 24 V 12 R₂=652 R₁ = 802 ¹2 13 R3=452 W =₂=10 V

Physics for Scientists and Engineers, Technology Update (No access codes included)

9th Edition

ISBN:9781305116399

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter28: Direct-current Circuits

Section: Chapter Questions

Problem 28.21P: Consider the circuit shown in Figure P28.21 on page 860. (a) Find the voltage across the 3.00-0...

See similar textbooks

Similar questions

A 20.00-V battery is used to supply current to a 10-k resistor. Assume the voltage drop across any wires used for connections is negligible, (a) What is the current through the resistor? (b) What is the power dissipated by the resistor? (c) What is the power input from the battery; assuming all the electrical power is dissipated by the resistor? (d) What happens to the energy dissipated by the resistor?
Consider a circuit that consists of a real battery with an emf and an internal resistance of r connected to a variable resistor R. (a) In order for the terminal voltage of the battery to be equal to the emf of the battery, what should the resistance of the variable resistor be adjusted to? (b) In older to get the maximum current from the battery, what should the resistance variable resistor be adjusted to? (c) In order for the maximum power output of the battery to be reached, what should the resistance of the variable resistor be set to?
A 160F capacitor charged to 450 V is dischargedthrough a 31.2k resistor, (a) Find the time constant.(b)Calculate the temperature increase of the resistor, given that its mass is 2.50 g and its specific heat is 1.67kJ/kg °C,noting that most of the thermal energy is retained in the short time of the discharge, (c) Calculate the new resistance, assuming it is pure carbon. (d) Does this change in resistance seem significant?
A 1,00-?O voltmeter is placed in parallel with a 75.0kresistor in a circuit, (a) Draw a circuit diagram of the connection, (b) What is the resistance of the combination? If the voltage across the combination is kept the same as it was across the 75.0-kresistor alone, what is the percent increase in current? (d) If the current through the combination is kept the same as it was through the 75.0-kresistor alone, what is the percentage decrease in voltage? (e) Are the changes found in parts (c) and (d) significant? Discuss.
The variable resistor Ro in the circuit is adjusted until the power dissipated in Ro is 40 W. Find the values of Ro that satisfy this condition. V,=60 V and R,=7,5 0, R2=30 0, R3=3 0, R4=6 0 and V=9iy. R, R3 R4 Vs R R. V. Lütfen birini seçin: O a. 1,50 and 3,90 O b. 0,55 and 4,50 Oc. 1,80 and 7,50 O d. 0,70 and 4,10 e. 0,31 and 2,40 * Of. 0,40 and 3,60 g. 1,80 and 7,20
Consider the circuit in the diagram, with sources of emf listed below: Randomized Variablesℰ1 = 21 Vℰ2 = 46 Vℰ3 = 5.5 Vℰ4 = 43 V a. Find I1 in amps. b. Find I2 in amps. c. Find I3 in amps.
Find the current I through the circuit.I= (mA). Find the voltage across each resistor. Give your answer as a comma-separated list in unit of volt, as an absolute value. potential drops across R1, R2, R3, R4, and R5 (in volt, in order): What is the power supplied by the batteries—that is, the power dissipated or consumed by the circuit?P= (W).
I need a labled schematic on paper of the circuit showing + and - terminals of the battery, the direction of any current flowing through the circuit, and any voltage drop across any resistors. I also need the form of the equations dealing with I, R (or 1/R), and V equations filled in with the appropriate numbers and answer with units for this problem. Problem: Two resistances are connected in series to a voltage source. The voltage source (∆Vtot) is a 48-V source and the resister values are 6.4 Ω (R1) and 3.9 Ω (R2). Determine the equivalent resistance of the circuit. Determine the current in the circuit. Determine the voltage drop across each individual resistor.
In the circuit element shown, the current through the 6-W resistor is approximately 30 ww 6Ω 1 - 2.0 A HINT: 1. Find the Equivalent resistance of the parallel portion of the circuit. 1/Reg = 1/R1 + 1/R2 2. Find the Voltage drop across the parallel portion by using Ohm's Law. 3. Then, find the current by = VR O Amps 2.0 Amps 0.40 Amps 0.67 Amps 1.3 Amps
M 1 Ω 11 V 3 W Ω 16 V a. Write Kirchhoff's junction rule for all junctions in the circuit. b. Write Kirchhoff's loop rule for all the loops in the circuit. c. Solve the circuit by finding the values of all the currents. 2 Ω mi M In this assignment you will be following the problem solving strategy for Kirchhoff Rules. 1. Reproduce, as neatly as possible, on paper, the circuit shown above. Do not make the circuit too small as you will have to add things to it later. 2. Label all relevant points in this circuit. For your benefit these points are marked with dots in the Figure above and they include: circuits junctions (i.e. places where 3/more wires connect), wire "corners" (i.e. places where a single wire is bent), and locations between two components on a single straight wire. These will help identify loops as well as making it easier to keep track of potential differences. Use lower case letters (a, b, c, ...) for this task. 3. For each junction draw and label the currents coming in…
What is the equivalent resistor between the terminals a and b if you replace R1 by 38 Ohm and R2 by 34 Ohm ? This combination of resistors goes to infinity by repeating itself. Write your answer in units of Ohm. No decimal points is necessary. Maximum od 4% of error is accepted in your answer.
V1 1] Consider the circuit in the diagram with an unknown resistor R. The known resistor is R₁ = 1k, the power supply voltage is V, 12 Volts, and the measured output voltage is Vx8 Volts. Multisim insists on values, so I put -10 for the 12V unknown. I'll try to take this approach consistently in the homework diagrams, if possible. A) Determine the value of R. B) Determine the current i through the resistors. C) Determine the total power P supplied by the power supply. Hilt R1 ww 1kQ www Rx -122 XMM1 to is