Q) A two-segment shaft is used to transmit power at constant speed through the pulleys shown above and to the right. Power is input to the shaft at B through a torque of TB = 230 N'm. A torque of T4 = 60 N'm is observed at 4, and a torque of Tc 170 N m is observed at C. The external torques act in the directions indicated in the figure. Both shaft segments are made of phosphor bronze [G = 42 GPa] and both segments are solid shafts. Segment (1) has a diameter of di = 20 mm and segment (2) has a diameter of d2 = 35 mm. a. Determine the torque observed in segments b. Determine the maximum shear stress observed in the shaft c. Determine the angle of twist observed in segments TA TB Tc (1) (2) A B L1 = 300 mm %3D L2 = 915 mm.

Q) A two-segment shaft is used to transmit power at constant speed through the pulleys shown above and to the right. Power is input to the shaft at B through a torque of TB = 230 N'm. A torque of T4 = 60 N'm is observed at 4, and a torque of Tc 170 N m is observed at C. The external torques act in the directions indicated in the figure. Both shaft segments are made of phosphor bronze [G = 42 GPa] and both segments are solid shafts. Segment (1) has a diameter of di = 20 mm and segment (2) has a diameter of d2 = 35 mm. a. Determine the torque observed in segments b. Determine the maximum shear stress observed in the shaft c. Determine the angle of twist observed in segments TA TB Tc (1) (2) A B L1 = 300 mm %3D L2 = 915 mm.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The axis ABCD receives a torque of 500Nm from the motor and transmits movement to other devices, by means of belts and pulleys connected at B and C. If it is known that the torques exerted on pulleys B and C are as shown In the figure, determine the minimum radius the shaft must have. You should consider that at point D of the motor there is a bearing that acts as a support for the shaft as at point A. The material of the shaft and its allowable shear stress are indicated in the drawing.Determine:to. Free-Body diagram.b. Shear force diagrams.c. Bending moment diagrams.d. Identification of the critical point of the axis.e. Calculation of the axis radius. tperm=80MPa
The motor in the figure applies a torsion (torque) of 50 Nm to the shaft AB. This torque is transferred to the CD shaft with the help of gears at points E and F. Bearings at B, C and D points provide free rotation to the shafts. Calculate the torque T' on the CD Shaft? 50 mm 30 mm B 35 mm T 125 mm
The shaft shown in the figure is machined from AISI 1040 CD steel. The shaft rotates at 1600 rpm and is supported in rolling bearings at A and B. The applied forces are F₁ = 1600 lbf and F2 = 640 lbf. A steady torque of 1600 lbf-in is being transmitted through the shaft between the points of application of the forces. 1 / in ] A in [lin -10 in- F₁ in F₂ -10 in- All fillets in R. 12in] 3 in The value of the notch sensitivity is The value of the fatigue stress concentration factor is in NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. What is the value of the theoretical stress concentration factor for torsion, the notch sensitivity, and the fatigue stress concentration factor? (You must provide an answer before moving to the next part.) The value of the theoretical stress concentration factor for torsion is
The circular shaft shown (Figure 2) has dimensions D1 = 24 cm , L1 = 6 m, D2 = 17.5 cm, and L2 = 4 m with applied torques T1 = 100 kN⋅m and T2 = 40 kN⋅m. The shear modulus is G1 = 60 GPa. Point B is halfway between points A and C. a) Draw the torque diagram for the shaft, using the right-hand rule to determine the correct signs. b) For the given shaft, what is the angle of twist at the free end, point D?
The circular shaft shown (Figure 2) has dimensions D1 = 24 cm , L1 = 6 mm, D2 = 17.5 cm, and L2 = 4 mm with applied torques T1 = 100 kN⋅m and T2 = 40 kN⋅m. The shear modulus is G1 = 60 GPa. Point B is halfway between points A and C. a) Draw the torque diagram for the shaft, using the right-hand rule to determine the correct signs. b) For the given shaft, what is the angle of twist at the free end, point D?
A solid constant-diameter circular shaft is subjected to the torques of TA = 480 lb-ft, TB = 1060 lb-ft, Tc= 860 lb-ft, and Tp = 280 lb-ft, acting in the directions shown. The bearings shown allow the shaft to turn freely. (a) Plot a torque diagram showing the internal torque in segments (1), (2), and (3) of the shaft. Use the sign convention presented in %D Section 6.6. (b) If the allowable shear stress in the shaft is 5800 psi, what is the minimum acceptable diameter for the shaft? TB TA Tc (1) Tp (3) В C D Answer: (a) T1 = Ib-ft T2 = Ib-ft T3 = Ib-ft (b) d = in.
In a gearbox, a spur gear is mounted on a shaft at equal distances from twosupporting bearings. The shaft and mounted gear turn together at a speed of3600RPM. The gearbox is designed to transmit a maximum power of 3kW. Thegear contact angle is φ = 20°. The pitch diameter of the gear is dp = 30 in. a) Findthe radial force on each of the two bearings supporting the shaft.The ratio of the two bearings’ length and diameter is L/D = 0.5. The bearings aremade of acetal resin material with the following limits:Surface velocity limit, V, is 5m/s.Average surface-pressure limit, P, is 7 MPa.PV limit is 3000 psi-ft/min.b) Find the diameter of the shaft in order not to exceed the stated limits.
A two-segment shaft is used to transmit power at constant speed through the pulleys shown in the figure. Power is input to the shaft at B through a torque of TB 250 N-m. A torque of T₁ = 75 N·m is removed from the shaft at A, and a torque of Tc = 175 N-mis removed from the shaft at C. The external torques act in the directions indicated in the figure. Both shaft segments are made of phosphor bronze [G = 42 GPa] and both segments are solid shafts. Segment (1) has a diameter of d₁ = 24 mm and a length of L₁ = 305 mm. Segment (2) has a diameter of d₂ = 35 mm and a length of L₂ = 855 mm. Determine the rotation angle of pulley C relative to pulley A. (1) T₁ = L₁ i TB T₂ = i B (2) 12 Determine the internal torques, T₁ and T₂, in segments (1) and (2), respectively. Use the internal torque sign convention in Section 6.6. N-m Tc N.m с
The motor shown in the figure supplies 16.5 kW at 1540 rpm at A. Shafts (1) and (2) are each solid 28 mm diameter shafts. Shaft (1) is made of an aluminum alloy [ G=26 GPa], and shaft (2) is made of bronze [ G=45 GPa]. The shaft lengths are L1=3.3m and L2=2.9m, respectively. Gear B has 56 teeth, and gear C has 97 teeth. The bearings shown permit free rotation of the shafts. Determine: the rotation angle of gear D with respect to flange A. [Answer φD/A = 0.314 rad]
A solid circular shaft AB of length 504 mm is fıxed against rotation at both ends as shown in fig. The shaft has diameters d=41 mm and D= 62mm in parts AC and CB respectively. A torque 2T acts at section 'C'. What would be length 'b' in mm for the most economical design of shaft? 27 a
The arms AB and BC of the desk lamp shown in the figure are contained in a plane that makes an angle of 30º with the xy plane. The following forces and torques are applied: •A force F1, parallel to the y axis, applied at the point middle of bar AB. •A force of 8 N at point C, raised 45º above line CD which is parallel to the z axis. •A torque of 10 Nm at point B, which is parallel to line OE. F1 = 9N AB = 360 mm BC = 266 mm So, 1. Calculate and indicate the Force-Pare equivalent system in A 2. Assuming that the system is in equilibrium and that the support in ANO allows movement in either direction (both displacement and rotation), indicate the reaction forces and moments acting at point A.
The arms AB and BC of the desk lamp shown in the figure are contained in a plane that makes an angle of 30º with the xy plane. The following forces and torques are applied: •A force F1, parallel to the y axis, applied at the point middle of bar AB. •A force of 8 N at point C, raised 45º above line CD which is parallel to the z axis. •A torque of 10 Nm at point B, which is parallel to line OE. F1 = 9N AB = 360 mm BC = 266 mm So, 1. Calculate and indicate the Force-Pare equivalent system in A 2. Assuming that the system is in equilibrium and that the support in A no allows movement in either direction (both displacement and rotation), indicate the reaction forces and moments acting at point A.