please solve parts 31 and 32 Assuming a fixed distance between parallel plates with a uniform field, and assumingunchanged Townsend's coefficients, the pressure is changed and the breakdown voltage ismeasured with the following results:apresure 180 rthe breakdown voltage is found to be 360V.Answer Q29 & Q30Q.29. Find the value of the pressure for minimum breakdown voltage according to Paschen's law.C. 593.92 torr D. 553.92 tomA. 527. 92 torr B. 509.92 torrQ. 30. Find the value of the minimum breakdown voltage according to Paschen's law.C. 377.41 VD. 357.41 VA. 337.41 VB. 327.41 VQ. 31. A 4 kV, 110 Hz Schering bridge with a grounded detector as shown in fig. 4 has C-100PF. In a test on an insulator, the balance was obtained with C4-0.2 µF, R4-2102, and R3- 1402. By removing the insulator from the measuring system, the balance will be reached at R3-7002 and C4-0.004 µF. Take into account the system stray capacitance and leakage and find theinsulator parallel resistance Rp.:A. 306.62 MO B. 316.62 MD2C,326.62 MOD. 336.62 MNQ. 32. A generating voltmeter is used to measure a DC voltage. The value of the varyingcapacitance is given by 14+11 sin cot pF. If the current generated is 4cos ut A, and if the speedof the synchronous motor driving the generating voltmeter is 700 rpm, then the applied voltage is:A. 6.201 kV B. 7.751 kV C. 4961 kV D. 3.969 kV

Q. 31. A 4 kV, 110 Hz Schering bridge with a grounded detector as shown in fig. 4 has Cs-100 PF. In a test on an insulator, the balance was obtained with C4-0.2 µF, R4-2102, and R3-140 2. By removing the insulator from the measuring system, the balance will be reached at R3-700 £2 and C4-0.004 µF. Take into account the system stray capacitance and leakage and find the insulator parallel resistance Rp.: A. 306.62 MO B. 316.62 MD2 C, 326.62 M2 D. 336.62 MO

Q. 31. A 4 kV, 110 Hz Schering bridge with a grounded detector as shown in fig. 4 has Cs-100 PF. In a test on an insulator, the balance was obtained with C4-0.2 µF, R4-2102, and R3-140 2. By removing the insulator from the measuring system, the balance will be reached at R3-700 £2 and C4-0.004 µF. Take into account the system stray capacitance and leakage and find the insulator parallel resistance Rp.: A. 306.62 MO B. 316.62 MD2 C, 326.62 M2 D. 336.62 MO

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.16P: A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and...

See similar textbooks

Similar questions

Q1- The given ferromagnetic core relative permeability is 800. Determine the total reluctance of the core. 35 cm 10 cm 20 cm 5 cm 15 cm 45 cm 15 cm 15 cm 10 cm
For figure (1)draw and calculate the voltages waveform across each half of secondary winding and across load when 100sin2π60t applied across the primary, then find PIV.
What will be the value of the twiddle factor: W42
6. What is the effect of load inductance on the ripple current? 7. i effect of chonnine Bock and boost 8. Wh 9 What chopping 10. At what duty evcle does the load current rinnle current he
The ohmic resistance of a large magnetic contractor is measured to be 25 ohms. A 200V is impressed on the contractor and the current is taken as 5A. Determine the inductance in mH and the reactive power of the load. The frequency is 60 HZ
Please show you detailed solution Number 10 A voltage of 250 volts at 50 Hz is impressed on a circuit having a 60-ohm resistor, 35-?F capacitor, and a 0.25-henry inductor in series. Determine power factor. A. 0.979 C. 0.924 B. 0.862 D. 0.707
circut for the core. (₁ For the ferromagnetic core shown in the gure below draw the magnetic The magnitudes of the reluctances are not important but clearly indicate on your circuit every reluctance which should be calculated for the given core. 10 15 = 0.5A d DNI 15 0.03 N2 1₂ = 0.1A 9
8. Liquids with solid impurities a) Have higher dielectric strength b) Of large size have higher dielectric strength c) Have lower dielectric strength as compared to pure liquids d) None of the above 9. Peak to peak ripple is defined as a) the difference between average de voltage and peak value b) the difference between maximum and minimum de voltage c) the difference between maximum ac and average de voltages d) the difference between ac (rms) and average de voltages 10. In a Cockroft-Walton circuit, input voltage 100 kV load current 25 mA, supply frequency 100 Hz, each capacitor 10 nF. The optimum no. of stages for maximum output voltage is a) 1 b) 2 c) 10 d) 35
Draw the waveform of voltage and current under the following conditions: A current which lags the voltage by 60°. A current which leads the voltage by 60°. A current which is in phase with the voltage
Q.4/ choose true or false: 1. The reluctance of any core is proportional directly with the length of it and inversely with both the permeability and the cross-section area of it. 2. The number of parallel paths in wave windings is equal to twice of the number of poles. 3. In dc machines with same values of Z, N, Ø, the emf for wave winding type is more than emf of lab winding type. 4. If we insert a current in such a conductor subjected to a constant magnetic field, a movement will achieved giving the principle of electric generator.
Solve for B to E: Answers: a. 2247.8405 Ab. 292.0629 kVc. 2291.3829 Ad. 667.10875 MW, 53.2164 MVAR (cap), 669.228 MVAe. 32.89125 MW
Each of the conductor in a parallel-plate capacitor is calleda. dielectricb. insulatorc. platesd. terminal