Q.3 A firm produces frozen fruits and vegetables, and a venturimeter is used in this process.In a certain step of the process, the cherries are introduced to the cold air stream at -12oC with a 3 in. pipe connected vertically to the throat of the venturimeter. Venturimeter is connected to a pipe 4 in. in diameter. If the air velocity in the throat is 5 times the terminal velocity of the cherries and the ratio of throat/pipe diameter is 0.6, what should be the flow rate of air? Assume that the density of cherries is 1200 kg/m3 and the average diameters are 12 mm. What should be the lay-out of the pipeline between venturimeter and freeze-dryer to prevent the striking of the cherries to the walls? Is there any settling possibility of the cherries at the exit of the venturimeter? Q.3 A firm produces frozen fruits and vegetables, and a venturimeter is used in this process.In a certain step of the process, the cherries are introduced to the cold air stream at-12°C with a 3 in. pipe connected vertically to the throat of the venturimeter.Venturimeter is connected to a pipe 4 in. in diameter. If the air velocity in the throat is5 times the terminal velocity of the cherries and the ratio of throat/pipe diameter is 0.6,3what should be the flow rate of air? Assume that the density of cherries is 1200 kg/m'What should be the lay-out of the pipelineand the average diameters are 12 mm.between venturimeter and freeze-dryer to prevent the striking of the cherries to thewalls? Is there any settling possibility of the cherries at the exit of the venturimeter?Venturimeter

Answered: Image /qna-images/answer/27096a9a-c049-4437-bff0-9d942126eac0.jpg

Q.3 A firm produces frozen fruits and vegetables, and a venturimeter is used in this process.In a certain step of the process, the cherries are introduced to the cold air stream at -12oC with a 3 in. pipe connected vertically to the throat of the venturimeter. Venturimeter is connected to a pipe 4 in. in diameter. If the air velocity in the throat is 5 times the terminal velocity of the cherries and the ratio of throat/pipe diameter is 0.6, what should be the flow rate of air? Assume that the density of cherries is 1200 kg/m3 and the average diameters are 12 mm. What should be the lay-out of the pipeline between venturimeter and freeze-dryer to prevent the striking of the cherries to the walls? Is there any settling possibility of the cherries at the exit of the venturimete

Q.3 A firm produces frozen fruits and vegetables, and a venturimeter is used in this process.In a certain step of the process, the cherries are introduced to the cold air stream at -12oC with a 3 in. pipe connected vertically to the throat of the venturimeter. Venturimeter is connected to a pipe 4 in. in diameter. If the air velocity in the throat is 5 times the terminal velocity of the cherries and the ratio of throat/pipe diameter is 0.6, what should be the flow rate of air? Assume that the density of cherries is 1200 kg/m3 and the average diameters are 12 mm. What should be the lay-out of the pipeline between venturimeter and freeze-dryer to prevent the striking of the cherries to the walls? Is there any settling possibility of the cherries at the exit of the venturimete

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.33P

See similar textbooks

Similar questions

Water is being pumped the through one inch diameter piping arrangement to a higher elevation (5 meters up). Assume incompressible fluid conditions and some heat losses to the surroundings. At the inlet water pressure is 1 bar, temperature 15C, and volumetric flow rate is 0.02 m3/s. At the exit pressure is 2.2 bar, temperature is 10C and velocity of the stream is 40 m/s. Determine: a.Density of the inlet stream using NIST tables. b.Mass flow rate [kg/s] c.Determine h2 from known p2 and T2 using NIST tables d.Find heat rate removed from Q=m(h1-h2) Use Energy Balance Equation with enthalpy difference and in the units of kW to find pumping power in kW. NOTE: The heat is removed from the system, so it should be negative in your equation!
Consider a pipe on a horizontal plane: based on Bernoulli's equation A. none of the above B. the inlet velocity will be less than the outlet velocity C. the inlet velocity will be greater than the outlet velocity D. the elevation of the inlet will be greater than that of the outlet
Water is being pumped the through one inch diameter piping arrangement to a higher elevation (5 meters up). Assume incompressible fluid conditions and some heat losses to the surroundings. At the inlet water pressure is 1 bar, temperature 15C, and volumetric flow rate is 0.02 m3/s. At the exit pressure is 2.2 bar, temperature is 10C and velocity of the stream is 40 m/s. Determine: a.Density of the inlet stream using NIST tables. b.Mass flow rate [kg/s] c.Determine h2 from known p2 and T2 using NIST tables d.Find heat rate removed from Q=m(h1-h2) Use Energy Balance Equation with enthalpy difference and in the units of kW to find pumping power in kW. NOTE: The heat is removed from the system, so it should be negative in your equation! show all steps please
Water is being pumped the through one inch diameter piping arrangement to a higher elevation (5 meters up). Assume incompressible fluid conditions and some heat losses to the surroundings. At the inlet water pressure is 1 bar, temperature 15C, and volumetric flow rate is 0.02 m3/s. At the exit pressure is 2.2 bar, temperature is 10C and velocity of the stream is 40 m/s. Determine: a.Density of the inlet stream using NIST tables. b.Mass flow rate [kg/s] c.Determine h2 from known p2 and T2 using NIST tables d.Find heat rate removed from Q=m(h1-h2) Use Energy Balance Equation with enthalpy difference and in the units of kW to find pumping power in kW. NOTE: The heat is removed from the system, so it should be negative in your equation! show all steps please thanks
long. The inlet water temperature is 10 C, and the tube wall temperature is 15 C water temperature. k 0.585, Pr= 9.4, u= 1.31x10*,p= 992kg/m, CP= 4195 j/kg. higher than the water temperature all along the length of the tube. What is the exit %3D Q5//answer one of the following branches e jall al je yal A) cast iron pipe (k=75w/m. °C) air flows inside this pipe at 300°C the inner diameter is 0.06 m, the outer diameter 7cm,it is covered with insulation type glass wool with thick 4cm. with k= 0.055w/m.°C .the ambient temperature 6 °C by free V3. convection with heat transfer coefficient (20w/m2. °C) the heat transfer inside the pipe is 65 w/m?. °C. length of tube (L-2) determine 1-the heat lost from the hot air 2-the temperature drop across the pipe shell 3-the temperature drop across the insulation. 344 14. 1256 and B) Fill the blanks: of the 1. The thermal resistance of a medium depends on medium. 2 All law. pes of convection are governed by 10000, the flow is
Industrial pipes Do the guides allow movement of a pipe only in two directions (in a plane)?
Water at room temperature with a mass flow rate of 2 kg / s flows through a system of 2 pipes connected in series. The first piece of pipe is 10 m long 1 in. Sch. 40, the second piece of pipe is 15 m long 2 in. Sch 40 is made of commercial steel tubing. Piping system is horizontal. Calculate the pressure loss across both pipes and the pump power required to flow water through this piping system, ignoring the energy loss of the fitting. CREATE THE KNOWN AND UNKNOWN BY DRAWING THE SHAPE OF THE ORGANIZATION AND WRITE YOUR ASSUMPTIONS IN DETAIL
Mechanical-Energy Balance and Friction Losses. Hot water is being discharged from a storage tank at the rate of 0.223 ft3/s. The process flow diagram and conditions are the same as given in Example 2.10-6, except for different nominal pipe sizes of schedule 40 steel pipe as follows. The 20-ft-long outlet pipe from the storage tank is 1 1/2 in. pipe instead of 4-in. pipe. The other piping, which was 2-in. pipe, is now 2.5-in. pipe. Note that now a sudden expansion occurs after the elbow in the 1 1/2 in. pipe to a 2 1/2 in. pipe.
Problem 1. A fluid is flowing in a 20 cm diameter pipeline with a velocity of 5.50 m/sec. The pressure at the center of the pipe is 35 kPa, and the elevation of the pipe above an assume datum is 5 m. Compute the total energy flowing fluid if it is (a.) water, (b.) molasses (s = 1.20) and (c.) gas (w = 4.29 N/). ANSWERS MUST BE IN 3 DECIMAL PLACES ALL THE WAY.
A saturated steam at 410K is being transported in a pipeline (brass drawing tubing) at a rate of 1 grams/second. Pipe has inside diameter of 0.025 m . The tube is 100m long. The pressure at the entrance is 80kPa. What is the value of G in kg/s.m2?. (use Perry's Handbook for the properties and constants) R = 8314J/kgmol.K; MW=18.02g/mol
AIR IS FLOWING IN A DUCT WITH VELOCITY OF 7.62 M/S, AND A STATIC PRESSURE OF 2.16 CM WATER GAUGE. THE DUCT DIAMETER IS 1.22 M, THE BAROMETRIC PRESSURE OF 99.4 KPA, AND THE GAGE FLUID TEMPERATURE AND AIR TEMPERATURE ARE 30 DEG. C. 1. SOLVE FOR THE TOTAL HEAD AGAINST WHICH FAN WILL OPERATE IN CM OF AIR. 2. COMPUTE FOR POWER OF AIR IN HP 3. COMPUTE FOR POWER USING THE WATER FORMULA IN HP.
This error occurs if the airflow is not directly parallel with the pitot-static tube 1. Compressibility Error 2. Instrument ErroR 3. Position Error 4. None of the above