Q./A beam having a tee-shaped cross section is subjected to equal 12 kN.m bending moments, as shown in Figure 1. Determine the following: (a) the centroid location, and the moment of inertia about the z axis. (b) the bending stress at point H. State whether the normal stress at H is tension or compression. (c) the maximum bending stress produced in the cross section. State whether the stress is tension or compression. 100 mm 25 mm H. 175 mm 150 mm 12 kN-m 12 kN-m 25 mm rigu T-chaned cross section

Q./A beam having a tee-shaped cross section is subjected to equal 12 kN.m bending moments, as shown in Figure 1. Determine the following: (a) the centroid location, and the moment of inertia about the z axis. (b) the bending stress at point H. State whether the normal stress at H is tension or compression. (c) the maximum bending stress produced in the cross section. State whether the stress is tension or compression. 100 mm 25 mm H. 175 mm 150 mm 12 kN-m 12 kN-m 25 mm rigu T-chaned cross section

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The bending moment M is applied to the box beam in the x-y plane at the orientation show below. (a) Determine the maximum magnitude of the bending moment M so that the tensile bending stress in the member does not exceed 15 ksi. (b) Determine the angle that the neutral axis makes with the y-axis. (c) The position or positions on the beam where the maximum compressive bending stress occurs given your answer in a. Clearly indicate this on the figure below (also calculate the values) 4 in. B 4 in. M 6 in. 6 in.
1. 2. 10 mm 10 mm 3. 5 mm 100 mm A beam section as shown in the sketch is subjected to a bendingmoment of Mx = 4 kN.m and a shear force of V = 2.5KN. 50 mm 100 mm Calculate the position of the centroid and the the second moment of area of the section about the sentroid horizontally. Draw the bending stress distribution through the height of the beam by calculating the bending stress at the critical positions Draw the shear stress distribution trough the height of the beam by calculating the shear stress below the flanges and at the centroid. 4. Draw the stress condition below the flanges, at the centroid and at the top and bottom of the beam.(7) 5. Draw the shearflow through the section. Show calculations
or section T below, subject to eccentric loads, determine: a) The position of the centroid; b) The moments of Inertia Iz and Iy; c) The maximum bending stresses; d) Plot the position of the neutral line. Please, show me step by step. And, please, make the maximum bending stresses for the y and z axes.
Where is the centroid of the cross-section with respect to the bottom in mm? In reference to Item 1, calculate for the moment of inertia with respect to the neutral axis in mm4. In reference to Item 1, determine the maximum tension bending stresses produced in segment BC of the beam in MPa. In reference to Item 1, determine the maximum compression bending stresses produced in segment BC of the beam in MPa.
(a) The Figure la show the cross-section of a beam. All dimension are in cm. 10 2 10 Figure la (i) Calculate the centroid of the cross-section measured from the bottom of the cross section. (ii) Calculate the moment of inertia, I, for this cross-section. (iii)A pure bending moment of magnitude 1.0 kN.m is applied to the cross- section, generating compression above the neutral axis, and tension below. Calculate the maximum values of the tensile and compressive stress. (iv)The bending moment is removed. The same beam cross-section is now subject to a vertical shear force of 2.5 kN acting in the downward. Calculate the maximum horizontal shear stress. Where does it occur?
The beam is supported by a pin at point A and a roller at point C. A distributed load is applied to the beam. Neglect the weight and thickness of the beam. Hints: 1. will need to use similar triangles to find the height after sectioning at B. 2. Review direction of normal force, shear force and bending moment and which is positive or negative. W2 W1 A di d2 Values for the figure are given in the following table. Note the figure may not be to scale. Variable Value W1 190 N-m W2 440 N-m di 5 m d2 5 m a. Determine the magnitude of the normal force at point B, NB. . b. Determine the magnitude of the shear force at point B, VB- c. Is the shear force VB a positive or negative shear force? d. Determine the magnitude of the bending moment at point B, MB. e. Is the bending moment MB a positive or negative bending moment? Round your final answers to 3 significant digits/figures.
QUESTION 3 If the allowable bending stresses for a beam in one application is 6 kip/in2 in tension. The cross-section of the beam is W8 x 40. If the beam is 10 foot long and simply supported and has a concentrated load applied at x = 3 ft as shown below. • Generate the shear force and bending moment diagram in terms of P; • Based on the allowable maximum bending moment you just obtained above, calculate/ input the mazimm allowable value of the load P: please, pay attention to units, and calculate your answer to 1 decimal place.. 3 ft 7 ft kip.
Q/ For the beams and loading shown below. A-Draw the shear force and bending-moment diagrams. B- Determine the equations of the shear force and bending-moment curves for the segments CD in Figure 2 C- Compute the bending stress at point (a) on section C. D- Determine the values and locations of the maximum tensile and compression bending stresses. Figure (2) R Point a Radius of hole: 40kN 0.5m 30 20KN/m 0.7m A B D |B 1m Im 3m Radius = R= 100 mm
For the beam shown at right, determine the following: P= 1800 lb a. Maximum tensile bending stress b. Transverse shear stress at a the junction of the "TEE" (i.e., 2" above the neutral axis). c. Transverse shear stress at the neutral axis - 7.5 ft- - 7.5 ft- (a) d. Draw the stress elements -10 in. representing the state of stress at the junction of the “TEE" and at the neutral axis. | 2 in. 4 in. -N- 1600 10 in. 8 in. 42 in.k- (b)
A W360 × 72 standard steel shape is used to support theloads shown on the beam in Figure a. The shape is oriented sothat bending occurs about the weak axis, as shown in Figure b.Consider the entire 6 m length of the beam, and determine(a) the maximum tensile bending stress at any location along thebeam and(b) the maximum compressive bending stress at any locationalong the beam
Derive the formula for the bending stress of a beam with a rectangular cross section and triangular cross secrion. Thank you
5. A beam with the cross-sectional shape shown below is to carry a bending moment of +12 in *kip around the centroid z axis. [Answer: centroid 0.94353" from bottom, 1 = 0.5876 in4, o, = 22.6 ksi Compression] a. Find the centroid and moment of inertia of the beam around the centroid z-axis. b. Find the bending stress at points A, B, C and D on the cross-section. 0.38 in 1.1 in J0.57 in y 0.38 in 1.82 in C B A Tö 0.38 in