Q1) 1 000KVA 34500/400 Volt Dy connected distribution transformer has an electrical load of 500 kVA with the power factor of 0.8 ind. Determine the low voltage winding and line current under nominal voltage operation? (given voltages are in 3 phase system are always line to line voltages) Please write the answer clearly

Q1) 1 000KVA 34500/400 Volt Dy connected distribution transformer has an electrical load of 500 kVA with the power factor of 0.8 ind. Determine the low voltage winding and line current under nominal voltage operation? (given voltages are in 3 phase system are always line to line voltages) Please write the answer clearly

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.33P: Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage...

See similar textbooks

Similar questions

The symbol shown is a(n) a. iron core transformer. b. auto transformer. c. current transformer. d. air core transformer.
Q3- three phase step down transformer 1250 KVA, 11000/2200 V, 50 Hz . The resistance /phase and leakage reactance/phase of the primary winding are 0.78 ohm and 4.8 ohm and the corresponding values for the secondary winding are 0.01 ohm and 0.06 ohm respectively if the primary winding is connected in delta and secondary in star calculate: 1) The voltage to be applied at normal frequency to the primary to circulate full-load through it when the secondary is short-circuited ii) The full load copper loss
The core of a three phase, 60 Hz, 11000/750 V delta/star, 310 kVA, core-type transformer operates with a flux of 0.056 Wb. Find(i) number of H.V. and L.V. turns per phase.(ii) e.m.f. per turn(iii) full load H.V. and L.V. phase-currents
b) A single phase, 50 Hz transformer rated with power of 25 kVA has voltage ratio of 5000/250 V. If the low voltage side has 150 turns, Determine (i) the primary current, (ii) the secondary current, (iii) the number of turns in High voltage side, (iv) maximum value of flux.
Q#2 a) Explain the Difference between Single Phase & Three Phase transformers with a Comparison Chart. b) What are the Losses of Transformer and how these losses are to be determined
Based on Table Q1 (b), there are experiment for determine the breakdown strength of transformer oil. Based on the observation, evaluate the breakdown voltage if the gap distance of electrodes is 2.5 mm and sketch it in a relevant graph. Table Q1 (b) Gap spacing (mm) 2 3 Breakdown voltage (kV) 50 80 110 130
A single-phase, 240 kVA, 240/4800 V transformer has the parameters shown in Figure Q5. Determine I and V at the primary and secondary when transformer is operating at full load kVA, 0.8 power factor leading and 220 V at the primary side. Find the voltage regulation. Use actual values and per unit system. 0.002625 Q 0.009 0 1.05 Ω 3.6 Ω V2 40 0 30 Q Figure Q5
2. A 1040/208 volt, 60 Hz, 15 KVA transformer has 200 turns on the high side. Calculate: a) Number of turns on the low voltage side. b) The volts per turn induced in the high and low windings. c) Rated current on the high and low sides. d) If a load of 70% of full load, resistive, is connected to the low side, calculate the primary and secondary currents, also determine the transformation ratio.
c) A 100 kVA, 4500/250 V, 50 Hz single-phase transformer has 100 secondary turns.Determine: i.The primary current.ii.The secondary current.iii.The number of primary turns.
Give any sample of electrical components/processes that single and three phase electric transformer application plays important role. Draw the diagram and label each part. please draw me and label each part.
2.50 The nameplate on a 7.97-kV:266-V, 25-kVA single-phase transformer indicates that it has a series reactance of 7.5 percent (0.075 per unit). Calculate the series reactance in ohms as referred to (i) the low-voltage terminal and (ii) the high-voltage terminal. a. b. If three of these transformers are connected in a three-phase Y-Y connection, calculate (i) the three-phase voltage and power rating, (ii) the per unit impedance of the transformer bank, (iii) the series reactance in ohms as referred to the high voltage terminal and (iv) the series reactance in ohms as referred to the low-voltage terminal. c. Repeat part (b) if the three transformers are connected in Y on their HV
A single-phase 100 kVA, 2400/240 V, two-winding transformer will be used as a step-down auto-transformer in a 2640/2400 V system. The connection diagram of the transformer is given below. Calculate the I1, I2 and Ix currents given in the figure. Compare the kVA values of the auto transformer with the kVA values of two-winding transformers.